GDPR

projektai-lsd Lithuanian Standards Board
Portal for draft standards

Extended search

till

Results

Showing:
prEN ISO 19014-5 Public enquiry
Comment end date 2025-09-17
Earth-moving machinery - Functional safety - Part 5: Tables of performance levels (ISO/DIS 19014-5:2025)

This document will provide normative tables of machine performance levels required (MPLr) by common function and type for earth-moving machinery (EMM) as defined in ISO 6165:2022, except vacuum excavators. These MPLr can then be mapped or applied to safety control systems (SCS) used to control or that affect the functions defined in the table. The MPLr in this document are determined through the machine control system safety analysis (MCSSA) process outlined in EN ISO 19014-1:2018. A brief explanation of how the levels were derived and the associated assumptions are contained in the document.

prEN ISO 19014-3 Public enquiry
Comment end date 2025-09-17
Earth-moving machinery - Functional safety - Part 3: Environmental performance and test requirements of electronic and electrical components used in safety-related parts of the control system (ISO/DIS 19014-3:2025)

This document specifies the minimum requirements for environmental testing of electronic and electrical components identified as safety-related parts of the control system (SRP/CS) used on earth-moving machinery (EMM) as defined in ISO 6165 and their attachments.

prEN ISO 19014-2 Public enquiry
Comment end date 2025-09-17
Earth-moving machinery - Functional safety - Part 2: Design and evaluation of hardware and architecture requirements for safety-related parts of the control system (ISO/DIS 19014-2:2025)

This document specifies general principles for the development and evaluation of the machine performance level achieved (MPLa) of safety-control systems (SCS) using components powered by all energy sources (e.g. electronic, electrical, hydraulic, mechanical) used in earth-moving machinery and its equipment, as defined in ISO 6165. The principles of this document apply to machine control systems (MCS) that control machine motion or mitigate a hazard; such systems are assessed for machine performance level required (MPLr) per ISO 19014-1 or ISO/TS 19014-5. Excluded from the scope of this document are the following systems: —    awareness systems that do not impact machine motion (e.g. cameras and radar detectors); —    fire suppression systems, unless the activation of the system interferes with, or activates, another SCS. Other systems or components whereby the operator would be aware of failure (e.g. windscreen wipers, head lights, etc.), or are primarily used to protect property, are excluded from this document. Audible warnings are excluded from the requirements of diagnostic coverage. In addition, this document addresses the significant hazards as defined in ISO 12100 mitigated by the hardware components within the SCS. This document is not applicable to EMM manufactured before the date of its publication.

prEN ISO 19014-1 Public enquiry
Comment end date 2025-09-17
Earth-moving machinery - Functional safety - Part 1: Methodology to determine safety-related parts of the control system and performance requirements (ISO/DIS 19014-1:2025)

This document provides a methodology for the determination of performance levels required for earth moving machinery (EMM) as defined in ISO 6165. A Machine Control System Safety Analysis (MCSSA) determines the amount of risk reduction of hazards associated with control systems, required for Safety Control Systems (SCS). This reduction is quantified by the Machine Performance Level (MPL), the hazards are identified using the risk assessment principles as defined in ISO 12100 or by other means. NOTE 1 Step 2 as shown in Annex A demonstrates the relationship between ISO 12100 and ISO 19014 as a complementary protective measure. NOTE 2 ISO 19014 can also be used to assess the functional safety requirements of other off-road mobile machinery. For those controls determined to be safety-related, the characteristics for architecture, hardware, software environmental requirements and performance are covered by other parts in ISO 19014. ISO 19014 covers the hazards caused by the failure of a safety control system and excludes hazards arising from the equipment itself (for example, electric shock, fire, etc.). Other controls that are not safety control systems (SCS), that do not mitigate a hazard or perform a control function and where the operator would be aware of a failure, are excluded from this standard (e.g. windscreen wipers, head lights, cab light, etc.). NOTE 3 A list of safety control systems is included in Annex D. NOTE 4 Audible warnings are excluded from the requirements of diagnostic coverage.

prEN ISO 19014-4 Public enquiry
Comment end date 2025-09-17
Earth-moving machinery - Functional safety - Part 4: Design and evaluation of software and data transmission for safety-related parts of the control system (ISO/DIS 19014-4:2025)

This document specifies general principles for software development and signal transmission requirements of safety-related parts of machine-control systems (MCS) in earth-moving machinery (EMM) and its equipment, as defined in ISO 6165. In addition, this document addresses the significant hazards as defined in ISO 12100 related to the software embedded within the machine control system. The significant hazards being addressed are the incorrect machine control system output responses from machine control system inputs. Cyber security is out of the scope of this document. NOTE For guidance on cybersecurity, see an appropriate security standard. This document is not applicable to EMM manufactured before the date of its publication.

prEN 1868 Public enquiry
Comment end date 2025-09-11
Personal fall protection equipment - List of equivalent terms

This document specifies a list of terms connected to personal fall protection equipment standards. The terms are listed in the alphabetical order in the three official languages of CEN, English, German and French.

prEN 15011 Public enquiry
Comment end date 2025-09-11
Cranes - Bridge and gantry cranes

This document applies to bridge and gantry cranes able to travel by wheels on rails, runways or roadway surfaces, and to gantry cranes without wheels mounted in a stationary position. NOTE Light crane systems (assembly of lifting devices, crane bridges, trolleys and tracks; wall-mounted, pillar and workshop jib cranes) are covered by EN 16851. This document specifies requirements for all significant hazards, hazardous situations and events relevant to bridge and gantry cranes when used as intended and under conditions foreseen by the manufacturer (see Clause 4). This document does not include requirements for the lifting of persons. The specific hazards due to potentially explosive atmospheres, ionising radiation and operation in electromagnetic environment beyond the scope of EN 61000-6-2 are not covered by this document. This document is applicable to bridge and gantry cranes manufactured after the date of its publication as a European standard.

Quick filters

Technical Committee
TK 1 Electronics (9) TK 4 Information technology (2) TK 5 Electrical engineering (9) TK 6 Fruit and vegetables products (4) TK 8 Electromagnetic compatibility (2) TK 15 Cereals, cereal products, bread and animal feeding stuffs (1) TK 18 Telecommunications (5) TK 19 Concrete and reinforced concrete (1) TK 20 Toys, child use articles, sports and other recreational equipment (8) TK 21 Textiles and personal protective equipment (16) TK 22 Fire safety (3) TK 24 Quality management and quality assurance (2) TK 29 Water supply (9) TK 31 Acoustics (1) TK 32 Health (15) TK 33 Fishery (1) TK 35 Safety of machinery (7) TK 36 Environmental protection (2) TK 38 Building constructions (1) TK 39 Protection (2) TK 43 Railway traffic (16) TK 45 Electric power (6) TK 46 Roofs and building waterproof isolation (1) TK 50 Heating and Ventilation Systems (2) TK 51 Food analysis- Horizontal methods (3) TK 54 Assistive products for persons with disability (1) TK 56 Equipment for petroleum industry (4) TK 57 Fertilizers (3) TK 58 Refractory products and materials (dormant) (3) TK 68 Plastics (6) TK 71 Sustainably produced biomass for energy application, solid biofuel and solid recovered fuel (1) TK 76 Explosive atmospheres (5) TK 77 Lifts (4) TK 79 IT security techniques (2) TK 80 Road transport and traffic telematics (2) TK 82 Safety of trackless overground vehicles (2) TK 86 Geographic information (2) TK 87 Biotechnology (3) TK 98 Digital Product Passport (DPP) (8) TK 99 Health Informatics (1)
ICS
Biologinės dirvožemio savybės (2) Kiti su dirvožemio kokybe susiję standartai (1) Accident and disaster control (1) Acoustic measurements and noise abatement in general (1) Advanced ceramics (1) Aerospace electric equipment and systems (2) Alarm and warning systems (1) Alkaline secondary cells and batteries (1) Anaesthetic, respiratory and reanimation equipment (2) Biofuels (1) Biology. Botany. Zoology (3) Boilers and heat exchangers (1) Bolts, screws, studs (3) Buildings in general (1) Cabled distribution systems (1) Cables (1) Cableway equipment (2) Cereals, pulses and derived products (1) Chemicals for purification of water (8) Chimneys, shafts, ducts (1) Coatings and related processes used in aerospace industry (1) Concrete and concrete products (3) Cranes (1) Diagnostic, maintenance and test equipment (1) Disinfectants and antiseptics (1) Domestic safety (1) Domestic, commercial and industrial heating appliances (2) Earth-moving machinery (4) Electric furnaces (1) Electric road vehicles (1) Electrical and electronic equipment (2) Electrical and electronic testing (2) Electrical apparatus for explosive atmospheres (2) Electrical engineering in general (1) Electronic component assemblies (1) Emission (2) Environmental economics. Sustainability (5) Equipment for children (1) Equipment for the metallurgical industry (1) Explosion protection (1) Fibre optic interconnecting devices (2) Fibres and cables (3) Fire-fighting (1) Fire-resistance of building materials and elements (1) First aid (1) Fishing and fish breeding (1) Floor coverings (1) Food microbiology (1) Fuses and other overcurrent protection devices (1) Gas heaters (2) Ground service and maintenance equipment (1) Hand-operated tools (1) Head protective equipment (2) Heat pumps (3) Indoor sports equipment (1) Irons (1) IT applications in education (1) IT applications in health care technology (1) IT applications in industry (1) IT applications in science (1) IT applications in trade (4) IT applications in transport (2) IT Security (1) Items of art and handicrafts. Cultural property and heritage (1) Lifts. Escalators (1) Luminaires (1) Materials and components for railway engineering (1) Mechanical structures for electronic equipment (2) Metro, tram and light rail equipment (1) Multimedia systems and teleconferencing equipment (1) Non-destructive testing of metals (2) Other cells and batteries (4) Other fibre optic equipment (1) Other rubber and plastics products (1) Outdoor and water sports equipment (3) Petroleum products and natural gas handling equipment (1) Piezoelectric devices (1) Pipelines and its parts for external sewage systems (1) Plastics in general (1) Pressure regulators (1) Printed circuits and boards (1) Product and company certification. Conformity assessment (1) Protection against falling and slipping (1) Protective clothing (9) Radiation measurements (2) Radiographic equipment (1) Railway engineering in general (5) Railway rolling stock in general (1) Rectifiers. Converters. Stabilized power supply (2) Refractories (3) Refrigerating technology (1) RF connectors (1) Roofs (1) Sensory analysis (2) Small craft (1) Small kitchen appliances (1) Solar energy engineering (3) Special wastes (1) Spices and condiments (4) Sports facilities (4) Steel pipes and tubes for specific use (1) Superconductivity and conducting materials (1) Syringes, needles and catheters (2) Technical product documentation (1) TELECOMMUNICATIONS. AUDIO AND VIDEO ENGINEERING (5) Textiles in general (1) Theatre, stage and studio equipment (1) Thermoplastic materials (1) Trailing stock (1) Ventilation and air-conditioning systems (1) Welding processes (1)