List of drafts

Search keyword

Extended search

Reference

Directives

Organisation

ICS

Technical Committee

Foreign TC'S

Working group

Stage

Status

Comment date

till

Results

prEN ISO 3845 Public enquiry

Comment end date 2025-12-21

Oil and gas industries including lower carbon energy - Full ring ovalization test method for the evaluation of the cracking resistance of steel line pipe in sour service (ISO 3845:2024)

This document gives a method for determining the resistance to cracking of steel pipes in sour service. This test method employs a full-scale test specimen consisting of a short length of pipe (a ‘full ring’), sealed at each end to contain the sour test environment within. The test method applies to any pipe; seamless, longitudinally welded (with or without filler), helical welded, and to girth welds between pipes. NOTE 1 The specimen is usually a pipe but can also consist of flange neck or section of a bend, or other tubular component or a combination of the above. NOTE 2 This test method can also be used for corrosion resistant alloys (CRAs). The method utilizes ovalization by mechanical loading to produce a circumferential stress, equal to the target hoop stress, at two diametrically opposite locations on the inside surface of the test specimen. The test specimen is then subjected to single sided exposure to the sour test environment. NOTE 3 The test also allows measurement of hydrogen permeation rates.

View

prEN ISO 24202 Public enquiry

Comment end date 2025-12-21

Oil and gas industries including lower carbon energy - Bulk material for offshore projects - Monorail beam and padeye (ISO 24202:2023)

This document provides the design, construction and test requirement for the structures of monorail beams and pad eyes intended for material handling of the both onshore and offshore oil and gas projects. This document is based on major international standards to comply with requirements of shelf regulations of UK, US, Norway and Australia. Overall the requirements outlined in this document should meet most of the specified regulatory requirements. Exemptions where requirements in common standards are not met in this document are clearly stated.The standard shapes, dimensions and material grades are defined in this document.

View

prEN ISO 19900 Public enquiry

Comment end date 2025-12-21

Oil and gas industries including lower carbon energy - General requirements for offshore structures (ISO/DIS 19900:2025)

This document specifies general provisions for the design and assessment of fixed (bottom-founded) and floating (buoyant) offshore structures. This document contains general provisions for the design of new structures and site assessment of existing structures. This document is applicable for all phases of the life of the structure, including: ¾ pre-service (e.g., fabrication, transportation, installation), ¾ service in-place, both during originally specified design service life and during any life extensions, ¾ functional upgrade, repurpose and reuse, and ¾ decommissioning, and removal. This document focusses on primary and secondary load bearing structure but also provides some provisions for tertiary and ancillary structure. NOTE ISO 24201[22] covers the design of stairs, gratings and handrails. This document was initially created for offshore oil & gas structures but is now also applicable to renewable energy offshore structures. This document does not apply to pipelines, risers or subsea systems.

Read draft and comment View

prEN 13160-7 Public enquiry

Comment end date 2025-12-07

Leak detection systems - Part 7: Requirements and test/assessment methods for interstitial spaces, leak detection linings and leak detection jackets

This document specifies requirements and the corresponding test/assessment methods applicable to leak detection linings and leak detection jackets. Leak detection linings and leak detection jackets are intended to be used, in conjunction with leak detection kits, to create an interstitial space or leakage containment in single skin underground or above ground, non-pressurized tanks designed for water polluting liquids. For leak detection kits, see EN 13160 2, EN 13160 3 and EN 13160 4.

Read draft and comment View

prEN 13160-3 Public enquiry

Comment end date 2025-12-07

Leak detection systems - Part 3: Requirements and test/assessment methods for liquid systems for tanks

This document gives requirements and the corresponding test/assessment methods applicable to leak detectors based on the drop of the liquid level in the leak detection liquid reservoir. Leak detectors are intended to be used with double skin, underground or above ground, non-pressurized tanks designed for water polluting liquids. The liquid leak detectors are usually composed of: - sensing device (liquid sensor); - evaluation device; - alarm device.

Read draft and comment View

prEN 13160-2 Public enquiry

Comment end date 2025-12-07

Leak detection systems - Part 2: Requirements and test/assessment methods for pressure and vacuum systems

This document gives requirements and the corresponding test/assessment methods applicable to leak detector based on the measurement of pressure change. Leak detectors are intended to be used with double skin, underground or above ground, pressurized or non-pressurized, tanks or pipe designed for water polluting liquids/fluids. The leak detectors are usually composed of: - measuring device; - evaluation device; - alarm device; - pressure generator; - pressure relief device; - liquid stop device; - condensate trap.

Read draft and comment View

prEN 13160-4 Public enquiry

Comment end date 2025-12-07

Leak detection systems - Part 4: Requirements and test/assessment methods for sensor-based leak detection systems

This document gives requirements and the corresponding test/assessment methods applicable to sensor-based leak detection systems (leak detectors) for liquids and/or for gases. The leak detectors are intended to be used in interstitial spaces, leakage containments or monitoring wells. The leak detectors are usually composed of: - sensing device(s); - evaluation device; - alarm device.

Read draft and comment View

prEN ISO 15136-1 Public enquiry

Comment end date 2025-11-30

Petroleum and natural gas industries - Progressing cavity pump systems for artificial lift - Part 1: Pumps (ISO/DIS 15136-1:2025)

ISO 15136-1:2009 provides requirements for the design, design verification and validation, manufacturing and data control, performance ratings, functional evaluation, repair, handling and storage of progressing cavity pumps for use in the petroleum and natural gas industry. ISO 15136-1:2009 is applicable to those products meeting the definition of progressing cavity pumps (PCP) included herein. Connections to the drive string and tubulars are not covered in ISO 15136-1:2009. ISO 15136-1:2009 establishes requirements for characterization and testing of stator elastomer material, design validation and functional evaluation and provides information for PCP elastomer selection and testing, installation, start-up and operation guidelines, equipment selection and application guidelines, functional specification form, used pump evaluation, drive string selection and use, repair and reconditioning procedures and auxiliary equipment. Equipment not covered by the requirements of ISO 15136-1:2009 includes bottom-drive systems except for the PCP components, drive-string components and auxiliary equipment such as tag bars, gas separators and torque anchors.

Read draft and comment View

Mandatory cookies

Statistics cookies

Newsletter subscription

Extended search

Results

Quick filters

Organisation

Technical Committee

ICS