GDPR

projektai-lsd Lithuanian Standards Board
Portal for draft standards

Extended search

till

Results

Showing:
Total records found: 283
arrow-prev 1 … 8 9 10 11 12 arrow-next
prEN IEC 63758-4:2026 Public enquiry
Comment end date 2026-11-22
Qi specification - Version 2.3 - Part 4: Nfc tag protection (Fast Track)
prEN IEC 60335-2-83:2026 Public enquiry
Comment end date 2026-11-29
Household and similar electrical appliances - Safety - Part 2-83: Particular requirements for heated gullies for roof drainage

This European standard deals with the safety of electrically heated gullies for de-icing the inlet of the drainage system of flat roofs, balconies, and similar structures, their rated voltage being not more than 250 V including direct current (DC) supplied appliances and battery-operated appliances.

EN 12152:2023/prA1 Public enquiry
Comment end date 2026-11-07
Curtain walling - Air permeability - Performance requirements and classification

This document specifies requirements and classification of air permeability of both fixed and openable parts of curtain walling, under positive and negative static air pressure. This document applies to curtain walling as specified in EN 13830. NOTE This version of EN 12152:2023 will supersede EN 12152:2002. Existing test results according to EN 12152:2002 could be considered still valid compared with this version of EN 12152.

prEN IEC 60598-2-5:2026 Public enquiry
Comment end date 2026-11-08
Luminaires - Part 2-5: Particular requirements - Floodlights
prEN 302 448 V2.1.18 (2026-09) Public enquiry
Comment end date 2026-11-28
Satellite Earth Stations and Systems (SES); Earth Stations on Trains (ESTs) operating in the 11/12/14 GHz frequency bands; Harmonised Standard for access to radio spectrum
prEN 16883 Public enquiry
Comment end date 2026-12-03
Conservation of cultural heritage - Guidelines for improving the energy performance of historic buildings

This document provides guidelines for sustainably improving the energy performance of historic buildings, e.g. historically, architecturally or culturally valuable buildings, while respecting their significance. The use of this document is not limited to buildings with statutory heritage designation, it applies to historic buildings of all types and ages. This document presents a normative working procedure for selecting measures to improve energy performance, based on an investigation, analysis and documentation of the building including its significance. The procedure assesses the impact of those measures in relation to preserving the character-defining elements of the building.

prEN ISO 9360-2 Archived
Comment end date 2026-10-24
Heat and moisture exchangers, and breathing system filters for respired gases - Part 2: Measurement of moisture loss (ISO/DIS 9360-2:2026)
prEN IEC 63567-3:2026 Public enquiry
Comment end date 2026-11-15
Semiconductor devices - Performance evaluation of semiconductor processing components and inspection equipment - Part 3: Nano-scale wafer surface inspection method using UV light
prEN IEC 63758-1-2:2026 Public enquiry
Comment end date 2026-11-22
Qi specification - Version 2.3 - Part 1-2: General - Glossary (Fast Track)
prEN IEC 62228-5:2026 Public enquiry
Comment end date 2026-12-04
Integrated circuits - EMC evaluation of transceivers - Part 5: Ethernet transceivers
prEN IEC 60335-2-68:2026 Public enquiry
Comment end date 2026-11-08
Household and similar electrical appliances - Safety - Part 2-68: Particular requirements for spray extraction machines, for commercial use

This standard deals with the safety of electrical portable, non-self-propelled motor-operated spray extraction machines with or without attachments and with or without electrical heating elements, intended for commercial indoor use. This standard applies to machines for commercial use. The following list, although not comprehensive, gives an indication of locations that are included in the scope: - public use areas such as hotels, schools, hospitals; - industrial locations, for example factories and manufacturing shops; - retail outlets, for example shops and supermarkets; - business premises, for example offices and banks; - rental services for those machines; - all uses other than normal housekeeping purposes. The following power systems are covered: - mains powered motors up to a rated voltage of 250 V for single-phase appliances and 480 V for other appliances, - battery-operated machines. This standard applies to machines in which the pressure of the employed cleaning agent does not exceed 2,5 MPa, and in which the product of the pressure (in MPa) and the flow of cleaning agent (in litres per minute) does not exceed 100, and in which the temperature of the cleaning agent at the spray nozzle outlet does not exceed 85 °C. This standard does not apply to - vacuum cleaners and water-suction cleaning appliances for household use (IEC 60335-2-2); - floor treatment machines for commercial use (IEC 60335-2-67, IEC 60335-2-72); - wet and dry vacuum cleaners, including power brush, for commercial use (IEC 60335-2-69); - hand-held and transportable motor-operated electric tools (IEC 60745 series, IEC 61029 series, IEC 62841 series). - machines designed for use in corrosive or explosive environments (dust, vapour or gas); - machines designed for picking up hazardous dusts (as defined in IEC 60335-2-69), inflammable substances, or glowing particles; - machines designed to handle hazardous solvents, such as flammable or explosive liquids;

prEN ISO 5667-3 Public enquiry
Comment end date 2026-11-24
Water quality - Sampling - Part 3: Preservation and handling of water samples (ISO/DIS 5667-3:2026)

This document specifies the general requirements for sampling, preservation, handling, transport and storage of all water samples for physicochemical, chemical, hydrobiological and microbiological analyses and determination of radiochemical analytes and activities. Guidance on the validation of storage times of water samples is provided in ISO/TS 5667-25 [2]. This document is not applicable to water samples intended for ecotoxicological assays, biological assays (which is specified in ISO 5667-16 [4]), passive sampling (which is specified in ISO 5667-23 [5]) and microplastics (which is specified in ISO 5667-27 [6]). This document is particularly appropriate when samples cannot be analysed on site and have to be transported to a laboratory for analysis.

prEN IEC/IEEE 80005-3:2026 Public enquiry
Comment end date 2026-11-15
Utility connections in port - Part 3: Low-voltage shore connection (LVSC) systems - General requirements

This document specifies provisions for the design, installation and testing of low-voltage shore connection (LVSC) systems, onboard ships and on shore, to supply the ship with electrical power from shore. This document is applicable to: – ships requiring up to 1 MVA while at berth; – three-phase shore connection systems rated 250 A and above, and with a nominal voltage rating of 400 V AC to 1 000 V AC; – shore-side connection systems; – shore-to -ship connection and interface equipment; – transformers and reactors; – semiconductor and rotating frequency convertors; – ship-side connection systems; – protection, control, monitoring, interlocking and power management systems. This document does not apply to: – inland navigation vessels; – high-voltage shore connection systems, including ships built in accordance with the annexes of IEC/IEEE 80005-1; – the electrical power supply during docking periods, for example dry docking and other out-of-service maintenance and repair; – systems to be operated by ordinary persons as defined in 3.19. NOTE 1 Other standards are available specifically for inland navigation vessels in Europe. NOTE 2 IEC 6 0092-507 is applicable to small vessels. NOTE 3 Additional or alternative requirements can be imposed by national administrations or the authorities within whose jurisdiction the ship is intended to operate and by the owners or authorities responsible for a shore power supply or distribution system. NOTE 4 High-voltage shore connection systems are covered by IEC/IEEE 80005-1. NOTE 5 Some existing 380 V AC ship systems can be supplied by 400 V AC.

prEN ISO 18082 Public enquiry
Comment end date 2026-11-26
Anaesthetic and respiratory equipment - Dimensions of non-interchangeable screw-threaded (NIST) low-pressure connectors for medical gases (ISO/DIS 18082:2026)

ISO 18082:2014 specifies the dimensions, the allocation and marking of non-interchangeable screw-threaded (NIST) connectors intended to be used at operating pressures up to 1 400 kPa, and for vacuum systems at pressures not greater than 60 kPa absolute. ISO 18082:2014 specifies NIST connectors intended for use with the following medical gases: oxygen; nitrous oxide; medical air; helium; carbon dioxide; xenon; specified mixtures of the gases listed above; oxygen-enriched air; air for driving surgical tools; nitrogen for driving surgical tools; use with vacuum.

prEN ISO 25086-2 Public enquiry
Comment end date 2026-12-05
Textiles - Determination of the snagging resistance of fabrics - Part 2: Rotating chamber test method using pins (ISO/DIS 25086-2:2026)

This document describes a test method for the determination of snagging resistance of a fabric using pins fitted in a rotating chamber.

EN IEC 60317-27-4:2020/prA2:2026 Public enquiry
Comment end date 2026-11-06
Amendment 2 - Specifications for particular types of winding wires - Part 27-4: Paper tape covered rectangular aluminium wire
prEN IEC 60335-2-69:2026/prAA:2026 Public enquiry
Comment end date 2026-11-08
Household and similar electrical appliances - Safety - Part 2-69: Particular requirements for wet and dry vacuum cleaners, including power brush for commercial use

This standard deals with the safety of electrical motor-operated vacuum cleaners, including back-pack vacuum cleaners, and dust extractors, for wet suction, dry suction, or wet and dry suction, intended for commercial indoor or outdoor use with or without attachments. These machines may be provided with a blowing or inflating function. The inner diameter of the dust container connector to the suction hose shall not exceed 200 mm. It also deals with the safety of centrally-sited vacuum cleaners, excluding the installation of the system. Attention is drawn to the fact that additional requirements on the safe installation of centrally-sited vacuum cleaners are not addressed by this standard but need to be taken into account. This standard applies to machines for commercial use. The following list, although not comprehensive, gives an indication of locations that are included in the scope: – public use areas such as hotels, schools, hospitals; – industrial locations, for example factories and manufacturing shops; – retail outlets, for example shops and supermarkets; – business premises, for example offices and banks; – all uses other than normal housekeeping purposes. These machines are not equipped with a traction drive. The following power systems are covered: – mains powered motors up to a rated voltage of 250 V for single-phase appliances and 480 V for other appliances, – battery-operated motors. This standard also applies to machines handling hazardous dust, such as asbestos, and combustible dust in other than an explosive dust atmosphere. Additional requirements for machines handling hazardous dust are given in normative Annex AA. Attention is drawn to the fact that in many countries additional requirements on hazardous substances might apply. Radioactive substances are not covered by definition of hazardous dust for the purposes of this standard. This standard does not apply to – vacuum cleaners and water-suction cleaning appliances for household use (IEC 60335-2-2); – floor treatment machines for commercial use (IEC 60335-2-67, IEC 60335-2-72); – spray extraction machines for commercial use (IEC 60335-2-68); IEC 60335-2-67 and IEC 60335-2-68 cover only machines without traction drive. – hand-held mains-operated electrical garden blowers, vacuums and blower vacuums (IEC 60335-2-100); – hand-held and transportable motor-operated electric tools (IEC 60745 series, IEC 61029 series, IEC 62841 series); – appliances for medical purposes (IEC 60601-1); – machines designed for use in corrosive environments; – machines designed for picking up liquids with a flash point below 55 °C; – machines designed for use in explosive environments (dust, vapour or gas), except those designed for use in zone 22; – machines intended to vacuum ash from fireplaces, chimneys, ovens, ashtrays and similar places of ash accumulation.

prEN IEC 63758-13:2026 Public enquiry
Comment end date 2026-11-22
Qi specification - Version 2.3 - Part 13: Thermal management protocol (Fast Track)
prEN 1538 Public enquiry
Comment end date 2026-11-05
Execution of special geotechnical work - Diaphragm walls

This European Standard establishes general principles for the execution of diaphragm walls as either retaining walls or cut-off walls. NOTE 1 This standard covers only structures constructed in a trench excavated with a support fluid or in dry conditions, where soil is removed and replaced by concrete or slurry and with wall thickness B ≥ 40 cm. NOTE 2 Diaphragm walls can be permanent or temporary structures. NOTE 3 The following types of structure are considered: a) retaining walls: usually constructed to support the sides of an excavation in the ground. They include: 1) cast in situ concrete diaphragm walls; 2) precast concrete diaphragm walls; 3) reinforced slurry walls; b) cut-off walls: usually constructed to prevent migration of groundwater, clear or polluted, or of other contaminants present in the ground. They include: 1) slurry walls (possibly with membranes or sheet piles); 2) plastic concrete walls. NOTE 4 Walls formed shallow vertical trenches (typically excavations with a ratio of depth over thickness D/B < 5 or D < 5 m) are not covered by this standard.

prEN 1491 Public enquiry
Comment end date 2026-11-22
Building valves - Expansion valves - Tests and requirements

This document specifies dimensions, materials and performance requirements (including methods of test) for expansion valves, of nominal sizes from DN 15 to DN 50, having working pressures ) from 0,1 MPa (1 bar) to 1,0 MPa (10 bar). Expansion valves are intended for fitting to the cold potable water supply of storage water heaters, having a maximum distribution temperature of 95 °C, for all energy sources. Expansion valves do not control the temperature and alone do not constitute the protection required for storage water heaters. Expansion valves limit pressure, in the water heaters to what they are fitted, that is produced by thermal expansion of the water. NOTE The use of the device specified in this document does not override the need to use controls (e.g. thermostats and cut-outs) which act directly on the power sources of water heaters (for more information see Annex A).

EN 18052:2025/prA1 Public enquiry
Comment end date 2026-12-06
Intelligent transport systems - ESafety - ECall end to end conformance testing for eCall HLAP in hybrid circuit switched/packet switched network environments

This document describes the key actors in the eCall chain of service provision in hybrid circuit switched/packet switched network environments as: 1) In-Vehicle System (IVS)/vehicle, 2) Mobile Network Operator (MNO), 3) Public Safety Answering Point (PSAP), and to provide conformance tests for actor groups 1) – 3). NOTE 1 Conformance tests are not appropriate nor required for vehicle occupants, although they are the recipient of the service. NOTE 2 Third party eCall systems (TPS-eCall) are not within the scope of this deliverable. This is because the core TPS-eCall standard (EN 16102) does not specify the communications link between the vehicle and the TPS service provider. NOTE 3 These conformance tests are partly based on the appropriate conformance tests from EN 16454 and CEN/prEN 17240. This deliverable therefore adapts and revises Conformance Test Protocols (CTP) from EN 16454 and CEN/prEN 17240 for hybrid circuit switched/packet switched network environments. This document complements EN 16454 and CEN/prEN 17240 and provides a suite of conformance tests for IVS equipment, MNOs and PSAPs, required to ensure and demonstrate compliance with CEN/prEN 17905. The scope covers conformance testing of new engineering developments, products and systems, and does not imply testing associated with individual installations in vehicles or locations.

ISO/DIS 11565 Public enquiry
Comment end date 2026-12-10
Road vehicles — Spark-plugs — Test methods and requirements
prEN IEC 61010-2-034:2026 Public enquiry
Comment end date 2026-11-22
Safety requirements for electrical equipment for measurement, control, and laboratory use - Part 2-034: Particular requirements for measurement equipment for insulation resistance and test equipment for electric strength
prEN 12452 Public enquiry
Comment end date 2026-11-08
Copper and copper alloys - Rolled, finned, seamless tubes for heat exchangers

This document specifies the composition, property requirements and tolerances on dimensions and form for rolled, finned, seamless copper and copper alloy tubes for heat exchangers. It is applicable to copper and copper alloy tubes supplied in the size range from 6 mm up to and including 35 mm outside diameter; from 1 mm up to and including 3,5 mm wall thickness of the unfinned section; and with fin height up to and including 4,5 mm. The sampling procedures and the methods of testing for verification of conformity to the requirements of this document are also specified.

EN 1995-1-2:2025/prA1 Public enquiry
Comment end date 2026-11-12
Eurocode 5 - Design of timber structures - Part 1-2: Structural fire design

1.1 Scope of EN 1995-1-2 (1) This document deals with the design of timber structures for the accidental situation of fire exposure and it is intended to be used in conjunction with EN 1995-1-1 and EN 1991-1-2. This document only identifies differences from, or supplements to, normal temperature design. (2) This document applies to timber structures required to fulfil a loadbearing function, separating function or both. (3) This document gives principles and application rules for the design of structures for specified requirements in respect of the aforementioned functions and the levels of performance. (4) This document applies to structures, or parts of structures, that are within the scope of EN 1995-1-1 and are designed accordingly. (5) The methods given in this document are applicable to all products covered by European technical product specifications made reference to in this document. 1.2 Assumptions (1) In addition to the general assumptions of EN 1990, the following assumptions apply: - the choice of the relevant design fire scenario is made by appropriate qualified and experienced personnel, or is given by the relevant national regulation; - any fire protection measure taken into account in the design will be adequately maintained.

Total records found: 283
arrow-prev 1 … 8 9 10 11 12 arrow-next

Quick filters

Technical Committee
TK 1 Electronics (33) TK 4 Information technology (4) TK 5 Electrical engineering (40) TK 9 Furniture (2) TK 13 Agricultural engineering (4) TK 18 Telecommunications (15) TK 20 Toys, child use articles, sports and other recreational equipment (1) TK 21 Textiles and personal protective equipment (2) TK 22 Fire safety (7) TK 23 Ceramic tiles, masonry and natural stones (1) TK 24 Quality management and quality assurance (1) TK 25 Matrix, gypsum and gypsum based products (1) TK 26 Thermal insulation materials (1) TK 29 Water supply (16) TK 32 Health (9) TK 36 Environmental protection (2) TK 38 Building constructions (14) TK 39 Protection (2) TK 40 Petroleuml, petroleum products, lubricants and alternative fuels (1) TK 41 Welding (8) TK 45 Electric power (6) TK 46 Roofs and building waterproof isolation (6) TK 49 Metallic materials (6) TK 50 Heating and Ventilation Systems (1) TK 51 Food analysis- Horizontal methods (1) TK 56 Metal liquid tanks and industrial pipelines (1) TK 57 Fertilizers (2) TK 59 Geotechnics (3) TK 60 Windows and doors (4) TK 68 Plastics (6) TK 76 Explosive atmospheres (2) TK 77 Lifts (1) TK 79 IT security techniques (3) TK 80 Road transport and traffic telematics (1) TK 81 Conservation of cultural property (1) TK 82 Safety of trackless overground vehicles (1) TK 86 Geographic information (1) TK 87 Biotechnology (8) TK 89 Risk management and organizational governance (1) TK 91 Asset management and technical maintenance (1) TK 94 Circural economy (1) TK 99 Health Informatics (2)
ICS
Hidrologinės dirvožemio savybės (1) Acid secondary cells and batteries (2) Aerospace electric equipment and systems (1) Alarm and warning systems (1) Aluminium products (1) Amplifiers (2) Anaesthetic, respiratory and reanimation equipment (6) Application of information technology in general (2) Binders. Sealing materials (1) Biology. Botany. Zoology (8) Boilers and heat exchangers (1) Brazing and soldering (1) Building accessories (1) Cement. Gypsum. Lime. Mortar (2) Chemical laboratories. Laboratory equipment (4) Chemicals for purification of water (9) Cleaning appliances (7) Cleanrooms and associated controlled environments (1) Coaxial cables. Waveguides (1) Dental implants (1) Diagnostic equipment (1) Domestic safety (8) Earthworks. Excavations. Foundation construction. Underground works (3) Electric road vehicles (3) Electrical and electronic equipment. Control systems (1) Electrical and electronic testing (1) Electrical apparatus for explosive atmospheres (1) Electrical equipment of ships and of marine structure (1) Emission (1) Environment. Health protection. Safety (Vocabularies) (1) Environmental economics. Sustainability (1) Equipment for children (1) Exploratory, drilling and extraction equipment (2) Fertilizers (1) Fibre optic interconnecting devices (1) Fibres and cables (1) Fire protection (1) Fire-fighting (4) Fire-resistance of building materials and elements (1) Floor coverings (2) Food microbiology (1) Forensic science (1) Furniture (2) Fuses and other overcurrent protection devices (2) Gas cylinders (1) Gas heaters (1) Geometrical Product Specification (GPS) (1) Governance and ethics (1) Hand-operated tools (1) Home economics in general (2) Identification cards. Chip cards. Biometrics (1) Immunity (1) Insulators (1) Integrated circuits. Microelectronics (2) Iron and steel pipes (1) IT applications in health care technology (1) IT applications in information, documentation and publishing (1) IT applications in science (1) IT applications in transport (1) IT Security (4) Items of art and handicrafts. Cultural property and heritage (1) Laminated sheets (1) Laundry appliances (2) Leather and furs (1) Lifts. Escalators (1) Lines, connections and circuits (1) Liquid fuels (1) Luminaires (3) Maintenance services. Facilities management (1) Mechanical testing of metals (1) Mining equipment in general (1) Multilayer applications (1) Navigation and control equipment (1) Networking (1) Non-ferrous metal pipes (2) Other fluid power system components (1) Other kitchen equipment (1) Other semiconductor devices (2) Other standards related to lamps (1) Paints and varnishes (2) Plastics in general (2) Playgrounds (3) Power transmission and distribution networks in general (1) Primary cells and batteries (1) Printed circuits and boards (2) Product life-cycles (1) Properties of surfaces (1) Protection against crime (1) Protective clothing (1) Pumps (2) Radiographic equipment (1) Refrigerating technology (1) Reinforced plastics (1) Relays (1) RF connectors (2) Road equipment and installations (1) Roofs (1) Safety of machinery (1) Seismic and vibration protection (1) Smart textiles (1) Stainless steels (2) Stationary containers and tanks (1) Steel structures (3) Sterilizing equipment (1) Surface preparation (2) Technical aspects (6) TELECOMMUNICATIONS. AUDIO AND VIDEO ENGINEERING (15) Telecontrol. Telemetering (1) Textile fabrics (1) Thermal and sound insulating materials (6) Thermoplastic materials (1) Timber structures (1) Transformers. Reactors (2) Ventilation and air-conditioning systems (1) Ventilators. Fans. Air-conditioners (3) Walls. Partitions. Façades (3) Water heating equipment (1) Water supply systems (7) Welded joints and welds (5) Welding equipment (2) Wires (11)