List of drafts

prEN 481 Public enquiry

Comment end date 2026-09-17

Workplace exposure - Size fraction definitions for measurement of airborne particles

This document specifies sampling conventions for airborne particle size fractions to assess health-related exposure resulting from the inhalation of particles in workplace atmospheres. Conventions are defined for the inhalable, thoracic and respirable fractions. The sampling conventions only describe the inhalation of particles and their penetration in the respiratory tract as governed by inertia (impaction). Exhaled particles and deposition in the respiratory tract by other mechanisms, e.g. diffusion, are not considered in this document. The sampling conventions defined in this document apply to both indoor and outdoor workplaces. The conventions assume particles penetration and only oral breathing as a worst-case scenario. Nevertheless, the conventions are applicable to both oral and nasal breathing. The conventions are defined based on assumptions given in Clause 6. The choice of convention for a specific application depends on the region of the respiratory tract affected by the health impact of the particle component of interest (see Clause 5). The conventions can be applied to various metrics, including particle number, length, surface area, volume, or mass, depending on the type of particle analysis performed on the sampled aerosol fraction. The health-related fraction concentrations defined in this document are often expressed as the mass of sampled particles per volume of sampled air to allow comparison with mass-based occupational exposure limit values. The conventions primarily apply to the aforementioned metrics, however, they are not applicable to situations involving limit values expressed in a different metric, such as fibre limit values defined by length, diameter, and aspect ratio, unless a measurement procedure explicitly specifies sampling a particular health-related size fraction [11]. The primary objective of this document is to establish standardized conventions for health-related particle size fractions. Sampling is generally carried out using dedicated samplers, for which there is no need to measure the aerodynamic size distribution of the airborne particles to be sampled. Samplers separating airborne particles into one or more relevant fractions are currently available. In general, no assumptions or pre-knowledge are needed on the number of modes, modal diameter(s) or width of the particle aerodynamic size distribution of the airborne particles to be sampled. The conventions in this document are intended to be used for the determination of the exposure of an average worker based on average penetration curves. This document is not intended to determine the deposited dose of an individual worker. The conventions are primarily intended for assessing workers’ exposure to airborne particles by sampling the airborne particles. This document does not apply to large particles emitted at high speed that travel due to their initial momentum, instead of being carried by the air (airborne) and aspirated into humans’ respiratory tract and aerosol samplers by suction (see Annex B). All wind speeds referenced throughout this document are based on the relative speed between the worker and the surrounding air.

Read draft and comment View

prEN IEC 60335-2-48:2026 Public enquiry

Comment end date 2026-09-02

Household and similar electrical appliances - Safety - Part 2-48: Particular requirements for commercial electric grillers and toasters

This European Standard deals with the safety of electrically operated commercial grillers and toasters not intended for household use. The rated voltage being not more than 250 V for single-phase appliances connected between one phase and neutral, and 480 V for other appliances. Rotary or continuous grillers and toasters and similar appliances intended for grilling by radiant heat such as rotisseries, salamanders, etc. are within the scope of this standard. Appliances within the scope of this standard are typically used in restaurants, canteens, hospitals and commercial enterprises such as bakeries, butcheries, etc.

Read draft and comment View

prEN ISO 19161-2 Public enquiry

Comment end date 2026-09-19

Geographic information - Geodetic references - Part 2: Unique identification of geodetic ground stations (ISO/DIS 19161-2:2026)

This standard will provide a description of the numbering system replacing the DOMES numbering. The description of the DOMES numbering can be found in MERIT/COTES joint working groups, MERIT campaign: connection of reference frames, implementation plan, 1983. The standard will provide to the geodetic data producers and users a proper identification of the permanently instrumented stations, (e.g. those used in the production of the International Terrestrial Reference Frame and other similar stations), with special emphasis on the backward compatibility with existing DOMES numbers, which will have a positive impact on interoperability issues when merging several data from different communities. This standard will: • support interoperability among GNSS providers (GPS, GLONASS, GALILEO, BEIDOU, …) • clarify the potential confusion between communities which have already adopted their own numbering systems • support the UNGGIM GGRF resolution on global geodetic infrastructure.

Read draft and comment View

prEN ISO 21813 Public enquiry

Comment end date 2026-09-24

Fine ceramics (advanced ceramics, advanced technical ceramics) - Methods for chemical analysis of high purity barium titanate powders (ISO/DIS 21813:2026)

ISO 21813 specifies methods for the chemical analysis of fine high purity barium titanate powders used as the raw material for fine ceramics. ISO 21813 stipulates the determination methods of the barium, titanium, aluminium, cadmium, calcium, cobalt, dysprosium, iron, lead, magnesium, manganese, nickel, niobium, potassium, silicon, sodium, strontium, vanadium, zirconium, carbon, oxygen and nitrogen contents in high purity barium titanate powders. The barium and titanium contents, the major elements, are determined by using an acid decomposition-gravimetric method or an acid decomposition-inductively coupled plasma-optical emission spectrometry (ICP-OES) method. The aluminium, cadmium, calcium, chromium, cobalt, dysprosium, iron, lead, magnesium, manganese, nickel, niobium, potassium, silicon, strontium, vanadium and zirconium contents are simultaneously determined via an acid digestion-ICP-OES method. The nitrogen content is determined by using an inert gas fusion-thermal conductivity method, while that of oxygen is determined via an inert gas fusion-IR absorption spectrometry method. Finally, the carbon content is determined using a combustion-IR absorption spectrometry method or a combustion-conductometry method.

Read draft and comment View

prEN 196-15 Public enquiry

Comment end date 2026-10-13

Methods of testing cement - Part 15 - Sulfate resistance - Flat prism method

This document describes test methods (reference and alternative) applicable to cast test specimens for evaluating the Sulftate Resistance (SR characteristic) of cements. Sulfate resistance means that these binders can be used in concrete bodies submitted to sulfate attacks. In these methods, the test is carried out under controlled exposure conditions using an increased concentration of sulfate solution. These test conditions are intended to accelerate external sulfate attack. The reference test method is adapted from the modified SVA test method (German Institute for Building Technology (DIBt), Expert Committee (SVA)): “Testing the Sulfate Resistance of Cements with pozzolanic main constituents”. The modified SVA test method is listed in European Assessment Document – EAD 150007-01-0301, Annex C. This test method is appropriate for various binders, in particular those with pozzolanic main constituents. The alternative test method is listed in European Assessment Document – EAD 150009-01-0301, Annex A. This test method is appropriate for CEM III/A cements.

Read draft and comment View

prEN ISO 2076 Public enquiry

Comment end date 2026-09-30

Textiles - Man-made fibres - Generic names and specific names (ISO/DIS 2076:2026)

This document defines the generic names used to designate the different categories of man-made fibres, based on a main polymer, currently manufactured on an industrial scale for textile and other purposes, together with the distinguishing attributes that characterize them. The term “man-made fibres” has been adopted for those fibres obtained by a manufacturing process, as distinct from materials which occur naturally in fibrous form. This document gives recommendations of rules for the creation of the generic name (see Annex A). NOTE These rules have been introduced in the sixth edition of ISO 2076, and thus, they are not applicable to the existing generic names of the previous editions.

Read draft and comment View

ISO/IEC DIS 27004 Public enquiry

Comment end date 2026-09-01

Information technology — Security techniques — Information security management — Monitoring, measurement, analysis and evaluation

Read draft and comment View

ISO/DIS 6575 Public enquiry

Comment end date 2026-09-19

Fenugreek, whole or ground (powdered) — Specification

Read draft and comment View

prEN 4072 Public enquiry

Comment end date 2026-10-02

Aerospace series - Screw, 100° countersunk normal head, offset cruciform recess, close tolerance shank, short thread in titanium alloy, aluminium IVD coated - Classification: 1 100 MPa (at ambient temperature)/425 °C

This document specifies the characteristics of screws, 100° countersunk normal head, offset cruciform recess, close tolerance shank, short thread, in titanium alloy, aluminium IVD coated. Classification: 1 100 MPa /425 °C .

Read draft and comment View

prEN 204 Public enquiry

Comment end date 2026-10-15

Classification of thermoplastic wood adhesives for non-structural applications

This European Standard classifies thermoplastic resin based wood adhesives for non-structural applications into durability classes D1 to D4 based on the dry and wet strengths of bond-lines measured under specified conditions after various conditioning treatments. For special applications, further tests that do not fall within the scope of this European standard can be applicable. The adhesives specified in this European standard are suitable for the bonding of furniture and interior structures, panelling, doors, windows, stairs etc. made of wood or derived timber products. This European Standard does not specify the temperature resistance of bond-lines

Read draft and comment View

prEN ISO 17879 Public enquiry

Comment end date 2026-09-01

Gas cylinders - Self-closing cylinders valves - Specification and type testing (ISO/DIS 17879:2026)

ISO 17879:2017 specifies the design, type testing, marking and manufacturing tests and examinations requirements for self-closing cylinder valves intended to be fitted to refillable transportable gas cylinders which convey compressed, liquefied or dissolved gases. NOTE 1 The main applications for such self-closing cylinder valves are in the calibration gas and beverage industries. ISO 17879:2017 covers the function of a self-closing cylinder valve as a closure. NOTE 2 Requirements for standard cylinder valves are given in ISO 10297. Requirements for quick-release cylinder valves are given in ISO 17871. ISO 17879:2017 is not applicable to self-closing cylinder valves for cryogenic equipment, for portable fire extinguishers, or for liquefied petroleum gas (LPG). NOTE 3 Requirements for valves for cryogenic vessels are specified in ISO 21011 and at a regional level, for example, in EN 1626. Requirements for valves for portable fire extinguishers at a regional level are specified, for example, in EN 3 series. Requirements for self-closing LPG cylinder valves are specified in ISO 14245. NOTE 4 Additional requirements for pressure-relief devices might be specified in international/regional regulations/standards.

Read draft and comment View

prEN 50174-1:2026 Public enquiry

Comment end date 2026-09-04

Information technology - Cabling installation - Part 1: Installation specification and quality assurance

This document specifies requirements for the following aspects of information technology cabling: a) installation specification, quality assurance documentation and procedures; b) documentation and administration; c) operation and maintenance. This document is applicable to all types of information technology cabling including but not limited to generic cabling systems designed in accordance with the EN 50173 series. Examples of other types of information technology cabling covered by this document are: — Cable TV; — CCTV; — alarm and access control; — building control. NOTE Local regulations can also apply to the above mentioned cabling types. Safety (electrical safety and protection, optical power, fire, etc.) and electromagnetic compatibility (EMC) requirements are outside the scope of this document and are covered by other standards and regulations. However, information given in this document might be of assistance in meeting these standards and regulations.

Read draft and comment View

prEN IEC 80000-17:2026 Public enquiry

Comment end date 2026-09-20

Quantities and units - Part 17: Time dependency

Read draft and comment View

EN 1991-1-8:2026/prA1 Public enquiry

Comment end date 2026-09-24

Eurocode 1 - Actions on structures - Part 1-8: Actions from waves and currents on coastal structures

1.1 Scope of EN 1991 1 8 (1) EN 1991 1 8 gives principles and rules to determine the values of wave and current actions on structures and civil engineering works in the coastal zone, i.e. works connected to, or in close vicinity to the shore. NOTE 1 Provisions in EN 1991 1 8 are limited to hydrodynamic actions that can be directly quantified in terms of wave and/or current induced pressures and associated forces and moments on structures or structural parts. NOTE 2 As opposed to offshore conditions, waves or currents in the coastal zone are generally affected by the presence of the seabed or shore. NOTE 3 The coastal zone is typically defined as the area between the shoreline and the deep-water limit. (2) EN 1991 1 8 describes the principles for defining the hydrodynamic conditions to be used for design, including sea water levels. (3) EN 1991 1 8 addresses specifically actions from currents and waves on the following structure types: — cylindrical structures; — subsea pipelines; — suspended decks; — vertical face structures; — permanently moored floating structures. NOTE 1 Additional guidance can be needed for: — moored structures in the coastal zone for renewable energy production or related to oil and gas production or processing; — moored structures spanning areas with variable wave and current states (e.g. floating aquaculture farms or floating bridges). NOTE 2 For hydraulic pressures caused by quasi-static water levels, and ground water, see EN 1997 (all parts). (4) Actions addressed in EN 1991 1 8 do not cover: — hydraulic resonance in sheltered areas or basins (phenomena also known as harbour resonance); — translation waves, e.g. tsunamis; — waves and currents induced by maritime operations, i.e. vessel wake, berthing and mooring; — hydrodynamic actions induced by earthquakes; — ice-induced pressures and forces; — coastal structures where flood risk and/or erosion or sediment management is the dominant function. 1.2 Assumptions (1) The assumptions given in EN 1990 apply to this document. (2) In addition, it is assumed that actions from waves and currents on coastal structures are determined by personnel appropriately qualified and experienced in the following fields: a) physical coastal environment including physics of waves and currents, statistical properties and propagation of such; b) marine hydrodynamics, wave and current interaction with structures in general and wave and current actions on structures in the coastal zone including i) fixed structures, and ii) floating structures; c) advanced methods including probabilistic methodology and physical model testing.

Read draft and comment View

prEN 15119-1 Public enquiry

Comment end date 2026-10-15

Biological durability of wood and wood-based products - Determination of emissions from preservative treated wood to the environment - Part 1: Wood held in the storage yard after treatment and wooden commodities exposed in Use Class 3 (not covered, not in contact with the ground) - Laboratory method

This document specifies a laboratory method for obtaining water samples from preservative treated wood exposed out of ground contact (wood held in the storage yard after treatment and which has been in conditions designed to simulate outdoor, out of ground contact situations), at increasing time intervals after exposure.

Read draft and comment View

prEN ISO 1628-5 Archived

Comment end date 2026-08-25

Plastics - Determination of the viscosity of polymers in dilute solution using capillary viscometers - Part 5: Thermoplastic polyester (TP) homopolymers and copolymers (ISO/DIS 1628-5:2026)

This part of ISO 1628 specifies a method for the determination of the viscosity number (also referred to as "reduced viscosity") of dilute solutions of thermoplastic polyesters (TPs) in certain specified solvents. The method is applicable to poly(ethylene terephthalate) (PET), poly(butylene terephthalate) (PBT), poly-(cyclohexylenedimethylene terephthalate) (PCT), and poly(ethylene naphthalate) (PEN), as well as to copolyesters and other polyesters, referred to in ISO 20028-1:2019, that are soluble in one of the specified solvents under the specified conditions. The viscosity number is determined by the general procedure specified in ISO 1628-1:2024, observing the particular conditions specified in this part of ISO 1628. The determination of the viscosity number of a thermoplastic polyester provides a measure of the relative molecular mass of the polymer.

View

prEN 1914 Public enquiry

Comment end date 2026-09-03

Inland navigation vessels - Work boats, ship’s boats and lifeboats

This document applies to: - ship's boats that can be carried on inland navigation vessels according to ES-TRIN; - lifeboats if no special life-saving equipment (e.g. ADN1) is specified for the area of use; - work boats for the transport of a limited number of persons or smaller working loads in the construction site area and over comparatively short distances. This document does not apply to: - recreational craft according to Directive 2013/53/EU; - firefighting and water rescue boats.

Read draft and comment View

prEN IEC 63551-5:2026 Public enquiry

Comment end date 2026-09-20

Semiconductor devices - Chip-scale testing for autonomous vehicles - Part 5: Ultrasonic devices

Read draft and comment View

prEN 14434 Public enquiry

Comment end date 2026-10-01

Writing boards for educational institutions - Ergonomic, technical and safety requirements and their test methods

This document specifies ergonomic, technical and safety requirements for wall-mounted and free-standing writing boards, white projecting boards, interactive systems and interactive screens for use in rooms for educational and training purposes, e.g. classrooms, lecture theatres for schools, universities, etc. This document applies is applicable to units after installation. Safety depending on the structure of the building is not included, e.g. the strength of wall-mounted boards includes only the board and its parts. The wall and the wall attachment are not included. This document does not apply to technical aspects of connected hardware, such as computers, speakers, video cameras. Requirements concerning electrical safety are not included. Annex A (normative) Assessment scale for the ability to write – Five levels chalk scale Annex B (normative) Test methods and requirements for white projecting boards Annex C (informative) Additional test methods and requirements for white projecting boards Annex D (normative) Test methods and requirements for interactive systems Annex E (informative) Additional test methods and requirements for interactive systems Annex F (normative) Test methods and requirements for interactive screens Annex G (informative) Additional test methods and requirements for interactive screens Annex H (normative) Surface flatness test Annex I (informative) Vibration test

Read draft and comment View

EN 353-2:2024/prA1 Public enquiry

Comment end date 2026-10-22

Personal fall protection equipment - Part 2: Guided type fall arresters including a flexible anchor line

This document specifies requirements, test methods, marking, manufacturer’s instructions and information and packaging for guided type fall arresters including a flexible anchor line forming a single product. This anchor line is attached to an upper anchor point for vertical and inclined applications; for horizontal applications, the anchor point can be located at the user’s foot level. Guided type fall arresters including a flexible anchor line conforming to this document are components of one of the fall arrest systems covered by EN 363:2018. Other types of fall arresters are specified in EN 353-1:2014+A1:2017 or EN 360:2023.

Read draft and comment View

prEN 14972-18 Archived

Comment end date 2026-08-25

Fixed firefighting systems - Water mist systems - Part 18: Test protocol for local application involving flammable liquid fires for open nozzle systems

This document specifies the evaluation of the fire performance of water mist systems used for local application involving flammable liquid fires. The tests specified in this document are applicable to the following: a) flammable liquid pool fires where the liquid release can be confined to a bunded area, where the entire surface of the bunded area is protected by the water mist system; b) flammable liquid channel fires in channels not exceeding the maximum specified width of the water mist system and with no limited channel length; c) partially obstructed flammable liquid pool fires where the percentage of obstructed surface is limited to that tested; d) spray fires up to 6 MW fuelled by flammable liquids; e) spray and pool fire combinations where confined to a bunded area; f) flammable liquid residues (ink and paper dust) on printing presses.

View

ISO/IEC DIS 27007 Public enquiry

Comment end date 2026-09-01

Information security, cybersecurity and privacy protection — Guidelines for information security management systems auditing

Read draft and comment View

prEN ISO/IEEE 11073-10417 Public enquiry

Comment end date 2026-09-21

Health informatics - Device interoperability - Part 10417: Personal health device communication, device specialization, glucose meterr (ISO/IEEE FDIS 11073-10417:2026)

Within the context of the ISO/IEEE 11073 family of standards for device communication, ISO/IEEE 11073-10417:2017 establishes a normative definition of communication between personal telehealth glucose meter devices and compute engines (e.g., cell phones, personal computers, personal health appliances, and set top boxes) in a manner that enables plug-and-play interoperability. It leverages appropriate portions of existing standards, including ISO/IEEE 11073 terminology, information models, application profile standards, and transport standards. It specifies the use of specific term codes, formats, and behaviors in telehealth environments restricting optionality in base frameworks in favor of interoperability. This standard defines a common core of communication functionality for personal telehealth glucose meters.

Read draft and comment View

EN IEC 62020-1:2021/prA1:2026 Public enquiry

Comment end date 2026-10-04

Amendment 1 - Electrical accessories - Residual current monitors (RCMs) - Part 1: RCMs for household and similar uses

Read draft and comment View

ISO/DIS 9002 Archived

Comment end date 2026-08-24

Quality management systems — Guidelines for the application of ISO 9001

This document provides guidance on the intent of the requirements in ISO/DIS 9001 ISO 9001:2026, with examples of possible steps an organization can take to meet the requirements. It does not add to, subtract from, or in any way modify those requirements. This document does not prescribe mandatory approaches to implementation or provide any preferred method of interpretation.

View

Extended search

Results

Quick filters

Organisation

Technical Committee

ICS

Mandatory cookies

Statistics cookies

Newsletter subscription

List of drafts

Extended search

Results

Quick filters

Organisation

Technical Committee

ICS