List of drafts

Search keyword

Extended search

Reference

Directives

Organisation

ICS

Technical Committee

Foreign TC'S

Working group

Stage

Status

Comment date

till

Results

prEN ISO 11300-4 Public enquiry

Comment end date 2026-02-03

Piping systems for rehabilitation of underground drains, sewers and water supply networks - Part 4: Thermoplastic composite materials (ISO/DIS 11300‑4:2025)

This document specifies requirements and test methods for pipes and fittings which are part of piping systems for the renovation of underground non-pressure drainage and sewerage networks. It is applicable to pipes, fittings and assemblies, made from thermoplastic composite materials, as manufactured and as installed. It is not applicable to the existing pipeline. It is applicable to technique families for renovation: — lining with spirally-wound (SWO) pipes; — lining with a rigidly anchored plastic inner layer (RAPL). and intended to be used at an operating temperature of 20 °C as the reference temperature. In the case of lining with SWO pipes, where the pipes, are formed on site, to a fixed or variable diameter, by spirally winding and jointing a pre-manufactured profiled plastics strip, this document applies to, strips made of unplasticized poly(vinyl chloride) (PVC U), or of polyethylene (PE), with or without steel stiffening elements, and installed with or without integral locking mechanism. In the case of lining with RAPL, where a single rigid annulus of structural cementitious grout is formed behind a plastics inner layer serving as permanent formwork anchored to the grout. This document applies to integrally joined profiled plastics strips of PVC-U or PE or studded sheets of PE, and grout systems with or without steel reinforcement. It does not apply to the structural design of the lining system. NOTE Systems with multiple annuli are available, but these are controlled by patent rights and not covered by this document.

Read draft and comment View

prEN 13598-1 Archived

Comment end date 2026-01-27

Plastics piping systems for non-pressure underground drains and sewers - Unplasticized poly(vinyl chloride) (PVC-U), polypropylene (PP) and polyethylene (PE) - Part 1: Specifications for ancillary fittings and shallow chambers

This document is part of a System Standard for plastics piping systems of a particular material for a specified application. There are a number of such System Standards. System Standards are based on the results of the work being undertaken in ISO/TC 138 “Plastics pipes, fittings and valves for the transport of fluids”, which is a Technical Committee of the International Organization for Standardization (ISO). They are supported by separate standards on test methods, to which references are made throughout the System Standard. The System Standards are consistent with general standards on functional requirements and on recommended practice for installation. This document specifies the definitions and requirements for unplasticized polyvinyl chloride (PVC-U), polypropylene (PP) and polyethylene (PE) ancillary fittings and shallow chambers intended for use in non-pressure underground drains and sewers for wastewater. This document is applicable to: a) ancillary fittings and shallow chambers, intended for use buried underground outside the building structure; reflected in the marking of products by "U"; b) ancillary fittings and shallow chambers, intended for use buried underground both outside (application area code “U”) and within the building structure, reflected in the marking of products by "UD". This document also covers the jointing of the ancillary fittings and shallow chambers to the piping system. The document is applicable to the following ancillary fittings: - sealed access fittings; - rodding point covers; - rodding tees; - mechanical saddles. Ancillary fittings according to this document are intended for use in pedestrian areas, except rodding tees and mechanical saddles which can also be used in vehicular trafficked areas. Ancillary fittings can be installed to a maximum depth of 6,0 m from ground level, with the exception of rodding point covers with a maximum depth of 2,0 m. Shallow chambers according to this document are intended for use in private drains located in pedestrian areas above the ground water table, to a maximum depth of 2,0 m from ground level to the invert of the main flow channel. This document covers shallow chambers having a base with a flow channel and their joints to the piping system. Ancillary fittings and shallow chambers can be manufactured by various methods e.g. injection moulding, rotational moulding, spiral winding or fabricated. NOTE 1 Products complying with this document can be used with pipes, fittings and other components conforming to any of the plastics products standards listed in Annex E, providing their dimensions are compatible. NOTE 2 Products complying with this document can be installed in underground applications without additional static calculation. prEN 13598-1:2025 (E) 6 NOTE 3 Ancillary fittings and shallow chambers can be subject to national regulations and / or local provisions.

View

Mandatory cookies

Statistics cookies

Newsletter subscription

Extended search

Results

Quick filters

Organisation

Technical Committee

ICS