GDPR

projektai-lsd Lithuanian Standards Board
Portal for draft standards

Extended search

till

Results

Showing:
Total records found: 286
arrow-prev 1 … 10 11 12
EN 1998-1-2:2026/prA1 Archived
Comment end date 2026-11-12
Eurocode 8 - Design of structures for earthquake resistance - Part 1-2: Buildings

EN 1998-1-2 is applicable to the design and verification of new buildings and temporary structures in seismic regions.

EN 1995-2:2026/prA1 Archived
Comment end date 2026-11-12
Eurocode 5 - Design of timber structures - Part 2: Bridges

(1) This document gives design rules for the structural parts of bridges made of timber or other wood-based materials, either singly or compositely with concrete, steel or other materials. (2) The provisions of this document supplement, and in some cases modify or supersede, provisions given EN 1995-1-1. (3) Prestressed timber-concrete composite (TCC) members are not covered by this document. The design of stress-laminated timber decks used as part of a TCC system is covered. (4) TCC structures which rely on friction between wood and concrete are not covered by this document.

prEN 17093 Archived
Comment end date 2026-11-12
Domestic appliances used for drinking water treatment not connected to water supply - Jug water filter systems - Safety and performance requirements, labeling and information to be supplied

This European Standard describes the specifications and test methods for gravity fed devices for conditioning of drinking water that are not connected to the mains water distribution system in buildings, known as jug water filter systems. It also gives instructions for the user manuals, so that the jug water filter system can be used and maintained properly. Jug water filter systems are intended to modify the properties of drinking water only, and are not designed to make non-potable water safe for drinking. The scope of this document does not extend to combination systems that require an electrical power supply such as water heaters and water coolers systems. NOTE 1 Although jug water filter systems are covered by the widely harmonized food legislation (EU Regulations 178/2002 and 1935/2004), existing national regulations concerning the use and or the characteristics of these products remain in force NOTE 2 This standard provides no information as to whether the product is used without restriction in any of the Member States of the EU or EFTA.

EN 1995-1-2:2025/prA1 Archived
Comment end date 2026-11-12
Eurocode 5 - Design of timber structures - Part 1-2: Structural fire design

1.1 Scope of EN 1995-1-2 (1) This document deals with the design of timber structures for the accidental situation of fire exposure and it is intended to be used in conjunction with EN 1995-1-1 and EN 1991-1-2. This document only identifies differences from, or supplements to, normal temperature design. (2) This document applies to timber structures required to fulfil a loadbearing function, separating function or both. (3) This document gives principles and application rules for the design of structures for specified requirements in respect of the aforementioned functions and the levels of performance. (4) This document applies to structures, or parts of structures, that are within the scope of EN 1995-1-1 and are designed accordingly. (5) The methods given in this document are applicable to all products covered by European technical product specifications made reference to in this document. 1.2 Assumptions (1) In addition to the general assumptions of EN 1990, the following assumptions apply: - the choice of the relevant design fire scenario is made by appropriate qualified and experienced personnel, or is given by the relevant national regulation; - any fire protection measure taken into account in the design will be adequately maintained.

EN 1995-1-1:2025/prA1 Archived
Comment end date 2026-11-12
Eurocode 5 - Design of timber structures - Part 1-1: General rules and rules for buildings

1.1 Scope of prEN 1995-1-1 (1) prEN 1995-1-1 gives general design rules for timber structures. (2) prEN 1995-1-1 also gives specific design rules for buildings and timber civil engineering works. 1.2 Assumptions (1) The assumptions of EN 1990 apply to this document. (2) prEN 1995-1-1 is intended to be used in conjunction with EN 1990, EN 1991 (all parts), EN 1998 (all parts) when timber structures are built in seismic regions.

EN 1995-3:2025/prA1 Archived
Comment end date 2026-11-12
Eurocode 5 - Design of timber structures - Part 3: Execution

1.1 Scope of EN 1995-3 (1) This document gives minimum requirements for execution of timber structures (buildings and bridges) designed in accordance with EN 1995 (all parts) to ensure that what is built meets the requirements for mechanical resistance, serviceability, durability, and fire performance. (2) This document gives guidance on moisture control during transport to the building site, storage on site, handling on site and erection. (3) This document gives guidance on workmanship and deviation limits during execution. (4) This document assumes that there is an execution specification which states all the specific requirements relevant for the execution of a particular structure. (5) For products covered by a European technical product specification, this document only covers those aspects of fabrication such as cutting, machining and drilling after placement of the product on the market. (6) This document does not cover: a) parts which are not designed according to EN 1995; b) temporary works (such as formwork, scaffolding, propping, shoring, etc.); c) specification, production and conformity of timber members in accordance with European technical product specifications; d) deviation limits for other properties than mechanical resistance, serviceability, durability and fire performance; e) contractual aspects, responsibilities of the various parties, competency requirements or the degree of independence of the personnel undertaking the inspection; f) health and safety requirements during execution. 1.2 Assumptions (1) It is assumed that all relevant provisions of EN 1995 are complied with. (2) It is recognized in this document that areas such as detailed requirements for competence of personnel, and details related to Quality Management are within the competence of the CEN Member States. (3) Before the execution begins on a part of the structure, it is assumed that the following are available on site: — the drawings and specification of that part; — the execution specification. (4) Before the start of the execution, it is assumed that the execution specification has been checked for completeness. (5) It is assumed that previous work (such as foundations) has been inspected and that any work which needs to be done due to deviations from the execution specification has been carried out.

prEN ISO 15110 Archived
Comment end date 2026-11-12
Paints and varnishes - Artificial weathering including acidic deposition (ISO/DIS 15110:2026)

ISO 15110:2017 specifies a so-called acid dew and fog test (ADF test) as an accelerated laboratory test method for simulating, by the use of artificial acidic precipitation, the damaging effects of acidic atmospheric precipitation in association with UV radiation, neutral condensed precipitation, and changing temperature and humidity. This test method is intended to be used in evaluating, on the basis of relative performance rankings, the suitability of painted materials for use in outdoor environments with acidic precipitation. It is not intended to generate the same extent of damage or the same damage pattern as in outdoor weathering, but rather to give a ranking which is similar to that which would be obtained in outdoor weathering. The method produces damage which is more homogeneous, allows fewer specimens to be exposed (and hence more rapid testing) and enables evaluation of the exposed specimens to be carried out using methods which are more objective than visual assessment.

prEN ISO 15184 Archived
Comment end date 2026-11-12
Paints and varnishes - Determination of film hardness by pencil test (ISO/DIS 15184:2026)

This document specifies a method for determining the film hardness by pushing pencils of known hardness over the film. The test can be performed on a single coating of a paint, varnish or related product, or on the upper layer of a multi-coat system. This rapid test has not been found to be useful in comparing the pencil hardness of different coatings. It is more useful in providing relative ratings for a series of coated panels exhibiting significant differences in pencil hardness. The method is applicable only to smooth surfaces.

prEN 16175-2 Archived
Comment end date 2026-11-12
Soil, treated biowaste and sludge - Determination of mercury - Part 2: Cold-vapour atomic fluorescence spectrometry (CV-AFS)

This European Standard specifies a method for the determination of mercury in aqua regia or nitric acid digests of sludge, treated biowaste and soil, obtained according to EN ISO 54321 or EN 13173 using cold- vapour atomic absorption spectrometry (CV-AAS). The lower working range limit is at least 0,003 mg/kg (dry matter basis) depending on digestion parameters.

prEN 16175-1 Archived
Comment end date 2026-11-12
Soil, treated biowaste and sludge - Determination of mercury - Part 1: Cold-vapour atomic absorption spectrometry (CV-AAS)

This European Standard specifies a method for the determination of mercury in digests of soil, treated biowaste and waste, obtained according to EN ISO 54321 (aqua regia digestion) or EN 16173 (nitric acid digestion) or EN 13656 (digestion with a hydrochloric, nitric and tetrafluoroboric or hydrofluoric acid mixture) using cold-vapour atomic absorption spectrometry (CV-AAS). The lower working range limit is at least 0,03 mg/kg (drymatter basis) depending on digestion parameters.

prEN 18292 Public enquiry
Comment end date 2026-11-19
Inorganic fertilizers - Determination of the dry matter content

This document specifies the procedure for the determination/calculation of the dry matter content of inorganic fertilizers by gravimetric method for which the results of the performed analysis are expressed in relation to the dry matter basis. This document is applicable to inorganic fertilizers. This document is also applicable to blends of inorganic fertilizers.

Total records found: 286
arrow-prev 1 … 10 11 12

Quick filters

Technical Committee
TK 1 Electronics (33) TK 4 Information technology (2) TK 5 Electrical engineering (41) TK 9 Furniture (2) TK 15 Cereals, cereal products, bread and animal feeding stuffs (1) TK 18 Telecommunications (9) TK 19 Concrete and reinforced concrete (2) TK 21 Textiles and personal protective equipment (4) TK 22 Fire safety (7) TK 23 Ceramic tiles, masonry and natural stones (1) TK 24 Quality management and quality assurance (1) TK 26 Thermal insulation materials (1) TK 29 Water supply (15) TK 32 Health (8) TK 35 Safety of machinery (5) TK 36 Environmental protection (6) TK 38 Building constructions (16) TK 39 Protection (1) TK 40 Petroleuml, petroleum products, lubricants and alternative fuels (1) TK 41 Welding (5) TK 43 Railway traffic (1) TK 45 Electric power (9) TK 46 Roofs and building waterproof isolation (1) TK 49 Metallic materials (6) TK 50 Heating and Ventilation Systems (1) TK 51 Food analysis- Horizontal methods (1) TK 56 Metal liquid tanks and industrial pipelines (1) TK 57 Fertilizers (3) TK 59 Geotechnics (2) TK 60 Windows and doors (1) TK 68 Plastics (12) TK 76 Explosive atmospheres (2) TK 77 Lifts (1) TK 79 IT security techniques (2) TK 80 Road transport and traffic telematics (2) TK 81 Conservation of cultural property (1) TK 82 Safety of trackless overground vehicles (13) TK 86 Geographic information (1) TK 87 Biotechnology (1) TK 89 Risk management and organizational governance (1) TK 91 Asset management and technical maintenance (1) TK 99 Health Informatics (2)
ICS
Cheminės dirvožemio charakteristikos (1) Abrasives (1) Acid secondary cells and batteries (2) Aerials (1) Aerospace electric equipment and systems (1) Alarm and warning systems (1) Ambient atmospheres (3) Anaesthetic, respiratory and reanimation equipment (3) Animal and vegetable fats and oils (1) Application of information technology in general (1) Audio, video and audiovisual systems in general (1) Binders. Sealing materials (3) Biology. Botany. Zoology (1) Building accessories (1) Buildings and installations for processing and storage of agricultural produce (1) Cement. Gypsum. Lime. Mortar (1) Cereals, pulses and derived products (1) Chemicals for purification of water (9) Cleaning appliances (1) Cleanrooms and associated controlled environments (1) Coaxial cables. Waveguides (1) Commercial refrigerating appliances (1) Concrete and concrete products (2) Conveyors (1) Cranes (1) Dental implants (1) Diagnostic equipment (1) Disinfectants and antiseptics (1) Domestic electrical appliances in general (2) Domestic refrigerating appliances (2) Domestic safety (10) Electric road vehicles (3) Electrical and electronic equipment (11) Electrical and electronic equipment. Control systems (1) Electrical equipment of ships and of marine structure (1) Electroacoustics (1) Emission (1) Environment. Health protection. Safety (Vocabularies) (1) Exploratory, drilling and extraction equipment (2) Fertilizers (1) Fibre optic interconnecting devices (1) Fibres and cables (1) Fire protection (1) Fire-fighting (4) Fire-resistance of building materials and elements (1) Fissile materials and nuclear fuel technology (1) Flat steel products and semi-products (2) Floor coverings (2) Forensic science (1) Furniture (2) Fuses and other overcurrent protection devices (2) Galvanic cells and batteries (1) Gas cylinders (1) Gas heaters (1) Geometrical Product Specification (GPS) (1) Geotextiles (1) Governance and ethics (1) Hand-operated tools (1) Home economics in general (2) Identification cards. Chip cards. Biometrics (1) Immunity (1) Industrial trucks (1) Information technology (IT) in general (1) Insulators (1) Integrated circuits. Microelectronics (3) Interior finishing (3) Iron and steel castings (1) IT applications in health care technology (1) IT applications in science (1) IT applications in transport (2) IT Security (2) Items of art and handicrafts. Cultural property and heritage (1) Laboratory medicine in general (2) Laminated sheets (1) Laundry appliances (2) Lifts. Escalators (1) Lines, connections and circuits (1) Luminaires (2) Maintenance services. Facilities management (1) Materials and components for railway engineering (1) Measurement of electrical and magnetic quantities (2) Mechanical testing of metals (1) Metallic coatings (1) Metrology and measurement in general (1) Mining equipment in general (1) Multilayer applications (1) Navigation and control equipment (1) Networking (1) Other fibre optic equipment (1) Other fluid power system components (1) Other kitchen equipment (3) Other methods of testing of metals (1) Other semiconductor devices (2) Other standards related to lamps (1) Paints and varnishes (2) Petroleum products in general (1) Plastics fittings (1) Plastics in general (5) Plastics pipes (1) Playgrounds (3) Plug-and-socket devices. Connectors (1) Power transmission and distribution networks in general (1) Pressure regulators (1) Primary cells and batteries (2) Printed circuits and boards (3) Product life-cycles (1) Properties of surfaces (1) Protection against falling and slipping (1) Protective clothing (1) Refrigerating technology (1) Reinforced plastics (1) Roofs (1) Safety of machinery (2) Seismic and vibration protection (1) Smart textiles (1) Solar energy engineering (1) Stainless steels (3) Stationary containers and tanks (1) Steel structures (3) Steel wire, wire ropes and link chains (1) Sterilizing equipment (1) Technical aspects (6) TELECOMMUNICATIONS. AUDIO AND VIDEO ENGINEERING (9) Telecontrol. Telemetering (2) Textile fabrics (1) Textiles in general (2) Thermal and sound insulating materials (1) Thermoplastic materials (1) Timber structures (1) Transformers. Reactors (2) Valves in general (2) Ventilation and air-conditioning systems (1) Ventilators. Fans. Air-conditioners (2) Wastes in general (1) Water supply systems (6) Welded joints and welds (2) Welding consumables (1) Welding equipment (1) Welding, brazing and soldering in general (1) Wind turbine energy systems (1) Wires (2)