Standartų projektų sąrašas

prEN 1489 Viešoji apklausa

Komentavimo iki data 2026-11-22

Pastatų armatūra. Slėgio saugos vožtuvai. Bandymai ir reikalavimai

This document specifies dimensions, materials and performance requirements, including methods of test, for pressure safety valves, of nominal sizes from DN 15 to DN 40, having working pressures from 0,1 MPa (1 bar) to 1,0 MPa (10 bar). Pressure safety valves are intended for fitting to the potable water supply of storage water heaters, having a maximum storage temperature of 95 °C. Pressure safety valves limit the pressure in hot water heaters. Pressure safety valves do not control the temperature and alone do not constitute the protection required for storage water heaters. They are not intended to act as expansion valves under normal conditions. NOTE The use of the device specified in this document does not override the need to use controls (e.g. thermostats and cut-outs) which act directly on the power sources of water heaters (for more information see Annex A).

Skaityti, komentuoti projektą Peržiūrėti metaduomenis

prEN ISO 20601 Viešoji apklausa

Komentavimo iki data 2026-11-14

Neardomoji suvirinimo siūlių kontrolė. Ultragarsinė kontrolė. Fazuotosios gardelės technologijos taikymas plonasieniams plieniniams komponentams (ISO/DIS 20601:2026)

This document specifies the application of phased array technology for the semi- or fully automated ultrasonic testing of fusion-welded joints in steel parts with thickness values between 3,2 mm and 8,0 mm. This meets the typical range of tube wall thickness values in boilers, which is an important application of this testing technology. The minimum and maximum value of the wall thickness range can be exceeded, when testing level "D" of this document is applied. This document applies to full penetration welded joints of simple geometry in plates, tubes, pipes, and vessels, where both the weld and parent material are low-alloy and/or fine grained steel. NOTE "Semi-automated testing" encompasses a controlled movement of one or more probes on the surface of a component along a fixture (guidance strip, ruler, etc.), whereby the probe position is unambiguously measured with a position sensor. The probe is moved manually. "Fully automated testing" includes mechanized propulsion in addition. Where material-dependent ultrasonic parameters are specified in this document, they are based on steels having a sound velocity of (5 920 ± 50) m/s for longitudinal waves, and (3 255 ± 30) m/s for transverse waves. It is necessary to take this fact into account when testing materials with a different velocity. This document provides guidance on the specific capabilities and limitations of phased array technology for the detection, location, sizing and characterization of discontinuities in fusion-welded joints. Ultrasonic phased array technology can be used as a stand-alone technique or in combination with other non-destructive testing (NDT) methods or techniques, during manufacturing and testing of new welds/repair welds (pre-service testing). This document specifies two testing levels: — level "C" for standard situations; — level "D" for different situations/special applications. This document describes assessment of discontinuities for acceptance purposes based on: — height and length; — amplitude (equivalent reflector size) and length; — go/no-go decision. This document does not include acceptance levels for discontinuities.

Skaityti, komentuoti projektą Peržiūrėti metaduomenis

prEN ISO 13350 Viešoji apklausa

Komentavimo iki data 2026-11-14

Ventiliatoriai. Srovinių ventiliatorių eksploatacinių charakteristikų bandymai laboratorijoje (ISO/DIS 13350:2025)

ISO 13350:2015 deals with the determination of those technical characteristics needed to describe all aspects of the performance of jet fans as defined in ISO 13349. It does not cover those fans designed for ducted applications, nor those designed solely for air circulation, e.g. ceiling fans and table fans. The test procedures described in this International Standard relate to laboratory conditions. The measurement of performance under on-site conditions is not included.

Skaityti, komentuoti projektą Peržiūrėti metaduomenis

prEN 14620-2 Viešoji apklausa

Komentavimo iki data 2026-11-22

Aikštelėse montuojamų, vertikalių, cilindrinių, plokščiadugnių talpyklų sistemų, skirtų laikyti atšaldytoms suskystintoms dujoms, kurių naudojimo temperatūra nuo 0 °C iki –196 °C, projektavimas ir gamyba. 2 dalis. Metaliniai komponentai

This document specifies general requirements for the materials, design, construction and installation of the metallic components of refrigerated liquefied gas tank systems. This document deals with the design and manufacture of site built, vertical, cylindrical, flat-bottomed tank systems for the storage of refrigerated, liquefied gases with operating temperatures between 0 °C and -196 °C.

Skaityti, komentuoti projektą Peržiūrėti metaduomenis

EN 1990-1:2023+A1:2026/prA2 Viešoji apklausa

Komentavimo iki data 2026-11-12

Eurokodas. Konstrukcijų ir geotechninio projektavimo pagrindai. 1 dalis. Naujos konstrukcijos

1.1 Scope of !EN 1990-1 (1) This document establishes principles and requirements for the safety, serviceability, robustness and durability of structures, including geotechnical structures, appropriate to the consequences of failure. (2) This document is also applicable for existing structures as specified in EN 1990-2. (3) This document is intended to be used in conjunction with the other Eurocodes for the design of buildings and civil engineering works, including temporary structures. (4) This document describes the basis for structural and geotechnical verification according to the limit state principle. (5) The verification methods in this document are based primarily on the partial factor method. NOTE 1 Alternative methods are given in the other Eurocodes for specific applications. NOTE 2 The Annexes to this document also provide general guidance concerning the use of alternative methods. deleted text (6) This document is also applicable for the design of structures where materials or actions outside the scope of EN 1991 (all parts) to EN 1999 (all parts) are involved. NOTE In this case, additional or amended provisions can be necessary. 1.2 Assumptions (1) It is assumed that reasonable skill and care appropriate to the circumstances is exercised in the design, based on the knowledge and good practice generally available at the time the structure is designed. (2) It is assumed that the design of the structure is made by appropriately qualified and experienced personnel. (3) The design rules provided in the Eurocodes assume that: - execution will be carried out by personnel having appropriate skill and experience; - adequate control and supervision will be provided during design and execution of the works, whether in factories, plants, or on site; - construction materials and products for new structures or new structural members will be used in accordance with the Eurocodes, the relevant product and execution standards, and project specifications; - the structure will be adequately inspected and maintained; - the structure will be used in accordance with the assumptions. NOTE Guidance on management measures to satisfy the assumptions for design, verification and execution is given in Annex B.

Skaityti, komentuoti projektą Peržiūrėti metaduomenis

EN 1990-2:2026/prA1 Viešoji apklausa

Komentavimo iki data 2026-11-12

Eurokodas. Konstrukcijų ir geotechninio projektavimo pagrindai. 2 dalis. Esamų konstrukcijų vertinimas

(1) This document provides provisions for the assessment of existing structures, including geotechnical structures, and the general principles for interventions, to be used in conjunction with prEN 1990-1. NOTE This document is based on the general requirements and principles of structural reliability provided in prEN 1990-1. (2) Unless otherwise specified, prEN 1990-1 applies. (3) This document covers general principles regarding actions for assessment, complementing EN 1991 (all parts). NOTE Provisions for seismic actions due to earthquake are provided in EN 1998-3. (4) This document does not cover the design of new structural parts that will be integrated into an existing structure. NOTE For the design of new structural parts, see prEN 1990-1. (5) This document does not provide: — specific rules for initiation of assessment; — specific rules on how to undertake interventions that may be carried out as a result of an assessment; — material-specific technical provisions for existing structures; — provisions for seismic assessment and retrofitting of existing structures. NOTE For provisions for seismic assessment and retrofitting of existing structures, see EN 1998-3.

Skaityti, komentuoti projektą Peržiūrėti metaduomenis

EN 1998-1-2:2026/prA1 Viešoji apklausa

Komentavimo iki data 2026-11-12

Eurokodas 8. Atsparių žemės drebėjimui konstrukcijų projektavimas. 1-2 dalis. Pastatai

EN 1998-1-2 is applicable to the design and verification of new buildings and temporary structures in seismic regions.

Skaityti, komentuoti projektą Peržiūrėti metaduomenis

EN 1995-2:2026/prA1 Viešoji apklausa

Komentavimo iki data 2026-11-12

Eurokodas 5. Medinių konstrukcijų projektavimas. 2 dalis. Tiltai

(1) This document gives design rules for the structural parts of bridges made of timber or other wood-based materials, either singly or compositely with concrete, steel or other materials. (2) The provisions of this document supplement, and in some cases modify or supersede, provisions given EN 1995-1-1. (3) Prestressed timber-concrete composite (TCC) members are not covered by this document. The design of stress-laminated timber decks used as part of a TCC system is covered. (4) TCC structures which rely on friction between wood and concrete are not covered by this document.

Skaityti, komentuoti projektą Peržiūrėti metaduomenis

prEN 17093 Viešoji apklausa

Komentavimo iki data 2026-11-12

Prie vandentiekio neprijungti buitiniai prietaisai geriamajam vandeniui apdoroti. Vandens filtravimo ąsočiai. Sauga ir eksploatacinės charakteristikos, ženklinimas ir teiktina informacija

This European Standard describes the specifications and test methods for gravity fed devices for conditioning of drinking water that are not connected to the mains water distribution system in buildings, known as jug water filter systems. It also gives instructions for the user manuals, so that the jug water filter system can be used and maintained properly. Jug water filter systems are intended to modify the properties of drinking water only, and are not designed to make non-potable water safe for drinking. The scope of this document does not extend to combination systems that require an electrical power supply such as water heaters and water coolers systems. NOTE 1 Although jug water filter systems are covered by the widely harmonized food legislation (EU Regulations 178/2002 and 1935/2004), existing national regulations concerning the use and or the characteristics of these products remain in force NOTE 2 This standard provides no information as to whether the product is used without restriction in any of the Member States of the EU or EFTA.

Skaityti, komentuoti projektą Peržiūrėti metaduomenis

EN 1995-1-2:2025/prA1 Viešoji apklausa

Komentavimo iki data 2026-11-12

Eurokodas 5. Medinių konstrukcijų projektavimas. 1-2 dalis. Konstrukcijų elgsenos ugnyje skaičiavimas

1.1 Scope of EN 1995-1-2 (1) This document deals with the design of timber structures for the accidental situation of fire exposure and it is intended to be used in conjunction with EN 1995-1-1 and EN 1991-1-2. This document only identifies differences from, or supplements to, normal temperature design. (2) This document applies to timber structures required to fulfil a loadbearing function, separating function or both. (3) This document gives principles and application rules for the design of structures for specified requirements in respect of the aforementioned functions and the levels of performance. (4) This document applies to structures, or parts of structures, that are within the scope of EN 1995-1-1 and are designed accordingly. (5) The methods given in this document are applicable to all products covered by European technical product specifications made reference to in this document. 1.2 Assumptions (1) In addition to the general assumptions of EN 1990, the following assumptions apply: - the choice of the relevant design fire scenario is made by appropriate qualified and experienced personnel, or is given by the relevant national regulation; - any fire protection measure taken into account in the design will be adequately maintained.

Skaityti, komentuoti projektą Peržiūrėti metaduomenis

EN 1995-1-1:2025/prA1 Viešoji apklausa

Komentavimo iki data 2026-11-12

Eurokodas 5. Medinių konstrukcijų projektavimas. 1-1 dalis. Bendrosios ir pastatų taisyklės

1.1 Scope of prEN 1995-1-1 (1) prEN 1995-1-1 gives general design rules for timber structures. (2) prEN 1995-1-1 also gives specific design rules for buildings and timber civil engineering works. 1.2 Assumptions (1) The assumptions of EN 1990 apply to this document. (2) prEN 1995-1-1 is intended to be used in conjunction with EN 1990, EN 1991 (all parts), EN 1998 (all parts) when timber structures are built in seismic regions.

Skaityti, komentuoti projektą Peržiūrėti metaduomenis

EN 1995-3:2025/prA1 Viešoji apklausa

Komentavimo iki data 2026-11-12

Eurokodas 5. Medinių konstrukcijų projektavimas. 3 dalis. Darbų atlikimas

1.1 Scope of EN 1995-3 (1) This document gives minimum requirements for execution of timber structures (buildings and bridges) designed in accordance with EN 1995 (all parts) to ensure that what is built meets the requirements for mechanical resistance, serviceability, durability, and fire performance. (2) This document gives guidance on moisture control during transport to the building site, storage on site, handling on site and erection. (3) This document gives guidance on workmanship and deviation limits during execution. (4) This document assumes that there is an execution specification which states all the specific requirements relevant for the execution of a particular structure. (5) For products covered by a European technical product specification, this document only covers those aspects of fabrication such as cutting, machining and drilling after placement of the product on the market. (6) This document does not cover: a) parts which are not designed according to EN 1995; b) temporary works (such as formwork, scaffolding, propping, shoring, etc.); c) specification, production and conformity of timber members in accordance with European technical product specifications; d) deviation limits for other properties than mechanical resistance, serviceability, durability and fire performance; e) contractual aspects, responsibilities of the various parties, competency requirements or the degree of independence of the personnel undertaking the inspection; f) health and safety requirements during execution. 1.2 Assumptions (1) It is assumed that all relevant provisions of EN 1995 are complied with. (2) It is recognized in this document that areas such as detailed requirements for competence of personnel, and details related to Quality Management are within the competence of the CEN Member States. (3) Before the execution begins on a part of the structure, it is assumed that the following are available on site: — the drawings and specification of that part; — the execution specification. (4) Before the start of the execution, it is assumed that the execution specification has been checked for completeness. (5) It is assumed that previous work (such as foundations) has been inspected and that any work which needs to be done due to deviations from the execution specification has been carried out.

Skaityti, komentuoti projektą Peržiūrėti metaduomenis

prEN ISO 12217-2 Viešoji apklausa

Komentavimo iki data 2026-10-25

Mažieji laivai. Stabilumo ir plūdrumo vertinimas ir skirstymas į kategorijas. 2 dalis. Burlaiviai (ISO/DIS 12217-2:2026)

This document specifies methods for evaluating the stability and buoyancy of intact (i.e. undamaged) boats. The flotation characteristics of boats susceptible to swamping are also encompassed. The evaluation of stability and buoyancy properties using this document will enable the boat to be assigned to a design category (A, B, C or D) appropriate to its design and maximum load. This document is principally applicable to boats propelled primarily by sail (even if fitted with an auxiliary engine) of 6 m up to and including 24 m hull length. However, it can also be applied to boats less than 6 m if they are habitable multihulls or can be applied if they do not attain the desired design category specified in ISO 12217‑3 and they are decked and have quick-draining recesses which comply with ISO 11812. In relation to habitable multihulls, this document includes assessment of susceptibility to inversion, definition of viable means of escape and requirements for inverted flotation. This document excludes: — inflatable and rigid-inflatable boats covered by the ISO 6185 series, except for references made in the ISO 6185 series to specific clauses of the ISO 12217 series; — gondolas and pedalos; — surfboards including sailing surfboards; and — hydrofoils and foil stabilized boats when not operating in the displacement mode. NOTE Displacement mode means that the boat is only supported by hydrostatic forces. It does not include or evaluate the effects on stability of towing, fishing, dredging or lifting operations, which need to be separately considered if appropriate.

Skaityti, komentuoti projektą Peržiūrėti metaduomenis

prEN ISO 12217-1 Viešoji apklausa

Komentavimo iki data 2026-10-25

Mažieji laivai. Stabilumo ir plūdrumo vertinimas ir skirstymas į kategorijas. 1 dalis. Ne burlaiviai (ISO/DIS 12217-1:2026)

This document specifies methods for evaluating the stability and buoyancy of intact (i.e. undamaged) boats. The flotation characteristics of boats susceptible to swamping are also encompassed. The evaluation of stability and buoyancy properties using this document will enable the boat to be assigned to a design category (A, B, C or D) appropriate to its design and maximum total load. This document is principally applicable to boats propelled by human or mechanical power of 6 m up to 24 m hull length. However, it can also be applied to boats of under 6 m if they do not attain the desired design category specified in ISO 12217‑3 and they are decked and have quick-draining recesses which comply with ISO 11812. In relation to habitable multihulls, this document includes assessment of susceptibility to inversion, definition of viable means of escape and requirements for inverted flotation. This document excludes: — inflatable and rigid-inflatable boats covered by the ISO 6185 series, except for references made in the ISO 6185 series to specific clauses of the ISO 12217 series; — personal watercraft covered by ISO 13590 and other similar powered craft; — gondolas and pedalos; — sailing surfboards; — surfboards, including powered surfboards; — hydrofoils and hovercraft when not operating in the displacement mode; and — submersibles. NOTE Displacement mode means that the boat is only supported by hydrostatic forces. It does not include or evaluate the effects on stability of towing, fishing, dredging or lifting operations, which need to be separately considered if appropriate.

Skaityti, komentuoti projektą Peržiūrėti metaduomenis

prEN 16423 Viešoji apklausa

Komentavimo iki data 2026-11-12

Suskystintosios naftos dujos. Ištirpusių likučių nustatymas. Dujų chromatografijos metodas, naudojant skysčio injekavimą į kolonėlę

This European Standard specifies a method for the determination of the dissolved residual matter, also known as evaporation residue, in liquefied petroleum gases (LPG), by gas chromatography in the range of (10 to 600) mg/kg (ppm mass). This test method quantifies soluble organic compounds (hydrocarbon materials), sometimes called ‘evaporation residue’, which can be present in liquefied petroleum gases and which are substantially less volatile than the LPG product, i.e. with a boiling point between 174 °C and 522 °C (C10 to C40). Higher boiling materials, or materials that adhere permanently to the chromatographic column, will not be detected. WARNING - This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Skaityti, komentuoti projektą Peržiūrėti metaduomenis

prEN ISO 9455-8 Viešoji apklausa

Komentavimo iki data 2026-11-12

Žematemperatūrio litavimo fliusai. Bandymo metodai. 8 dalis. Cinko kiekio nustatymas (ISO/FDIS 9455-8:2026)

Describes the principle, the reagents and materials, the apparatus, the test procedure, the calculation of results, the precision and the contents of the test report.

Skaityti, komentuoti projektą Peržiūrėti metaduomenis

prEN ISO 15110 Viešoji apklausa

Komentavimo iki data 2026-11-12

Dažai ir lakai. Dirbtinio klimato poveikis, įskaitant dengimą rūgštimi (ISO/DIS 15110:2026)

ISO 15110:2017 specifies a so-called acid dew and fog test (ADF test) as an accelerated laboratory test method for simulating, by the use of artificial acidic precipitation, the damaging effects of acidic atmospheric precipitation in association with UV radiation, neutral condensed precipitation, and changing temperature and humidity. This test method is intended to be used in evaluating, on the basis of relative performance rankings, the suitability of painted materials for use in outdoor environments with acidic precipitation. It is not intended to generate the same extent of damage or the same damage pattern as in outdoor weathering, but rather to give a ranking which is similar to that which would be obtained in outdoor weathering. The method produces damage which is more homogeneous, allows fewer specimens to be exposed (and hence more rapid testing) and enables evaluation of the exposed specimens to be carried out using methods which are more objective than visual assessment.

Skaityti, komentuoti projektą Peržiūrėti metaduomenis

prEN ISO 15184 Viešoji apklausa

Komentavimo iki data 2026-11-12

Dažai ir lakai. Plėvelės kietumo nustatymas bandant pieštuku (ISO/DIS 15184:2026)

This document specifies a method for determining the film hardness by pushing pencils of known hardness over the film. The test can be performed on a single coating of a paint, varnish or related product, or on the upper layer of a multi-coat system. This rapid test has not been found to be useful in comparing the pencil hardness of different coatings. It is more useful in providing relative ratings for a series of coated panels exhibiting significant differences in pencil hardness. The method is applicable only to smooth surfaces.

Skaityti, komentuoti projektą Peržiūrėti metaduomenis

prEN ISO 23279 Viešoji apklausa

Komentavimo iki data 2026-11-12

Neardomieji suvirinimo siūlių bandymai. Ultragarsiniai bandymai. Suvirinimo siūlių netolygumo apibūdinimas (ISO/DIS 23279:2026)

ISO 23279:2017 specifies how to characterize indications from discontinuities by classifying them as originating from planar or non-planar embedded discontinuities. This procedure is also suitable for indications from discontinuities that break the surface after removal of the weld reinforcement.

Skaityti, komentuoti projektą Peržiūrėti metaduomenis

prEN ISO 17640 Viešoji apklausa

Komentavimo iki data 2026-11-12

Neardomieji suvirinimo siūlių bandymai. Ultragarsiniai bandymai. Būdai, bandymo lygiai ir vertinimas (ISO/DIS 17640:2026)

This document specifies techniques for the manual ultrasonic testing of fusion-welded joints in metallic materials of thickness ≥8 mm which exhibit low ultrasonic attenuation (especially that due to scatter) at object temperatures from 0 °C to 60 °C. It is primarily intended for use on full penetration welded joints where both the welded and parent material are ferritic. Where material-dependent ultrasonic values are specified in this document, they are based on steels having an ultrasonic sound velocity of (5 920 ± 50) m/s for longitudinal waves and (3 255 ± 30) m/s for transverse waves. This document specifies four testing levels, each corresponding to a different probability of detection of imperfections. Guidance on the selection of testing levels A, B, and C is given in Annex A. This document specifies that the requirements of testing level D, which is intended for special applications, be in accordance with general requirements. Testing level D can only be used when defined by specification. This includes tests of metals other than ferritic steel, tests on partial penetration welds, tests with automated equipment, and tests at object temperatures outside the range 0 °C to 60 °C. This document can be used for the assessment of discontinuities, for acceptance purposes, by either of the following techniques: a) evaluation based primarily on length and echo amplitude of the discontinuity; b) evaluation based on characterization and sizing of the discontinuity by probe movement techniques.

Skaityti, komentuoti projektą Peržiūrėti metaduomenis

prEN ISO 11666 Viešoji apklausa

Komentavimo iki data 2026-11-12

Neardomoji suvirinimo siūlių kontrolė. Ultragarsinė kontrolė. Priėmimo lygiai (ISO/DIS 11666:2026)

ISO 11666:2018 specifies two ultrasonic acceptance levels known as acceptance level 2 (AL 2) and acceptance level 3 (AL 3) for full penetration welded joints in ferritic steels, which correspond to ISO 5817:2014, quality levels B and C. An acceptance level corresponding to ISO 5817:2014, quality level D is not included in this document, as ultrasonic testing is generally not requested for this weld quality. These acceptance levels are applicable to testing carried out in accordance with ISO 17640. ISO 11666:2018 applies to the testing of full penetration ferritic steel welds, with thicknesses from 8 mm to 100 mm. It can also be used for other types of welds, materials and thicknesses, provided the tests have been performed with necessary consideration of the geometry and acoustic properties of the component, and an adequate sensitivity can be employed to enable the acceptance levels of this document to be applied. The nominal frequency of probes used in this document is between 2 MHz and 5 MHz, unless attenuation or requirements for higher resolution call for other frequencies. It is important to consider the use of these acceptance levels in conjunction with frequencies outside this range carefully.

Skaityti, komentuoti projektą Peržiūrėti metaduomenis

prEN 301 908-26 V1.0.0 (2026-08) Viešoji apklausa

Komentavimo iki data 2026-11-09

IMT koriniai tinklai. Prieigos prie radijo ryšio spektro darnusis standartas. 26 dalis. Orlaivyje esanti vartotojo įranga (VĮ)

Skaityti, komentuoti projektą Peržiūrėti metaduomenis

prEN IEC 63439-2-1:2026 Viešoji apklausa

Komentavimo iki data 2026-11-08

Elektros gamybos, perdavimo ir skirstymo sistemų robotinė technika. 2-1 dalis. Bendrieji techniniai reikalavimai, keliami elektros perdavimo oro linijas tikrinančioms bepiločių orlaivių sistemoms

Skaityti, komentuoti projektą Peržiūrėti metaduomenis

prEN IEC 60335-2-68:2026/prAA:2026 Viešoji apklausa

Komentavimo iki data 2026-11-08

Buitiniai ir panašios paskirties elektriniai prietaisai. Sauga. 2-68 dalis. Ypatingieji reikalavimai, keliami komercinės paskirties purškiamosioms-siurbiamosioms valymo mašinoms

This standard deals with the safety of electrical portable, non-self-propelled motor-operated spray extraction machines with or without attachments and with or without electrical heating elements, intended for commercial indoor use. This standard applies to machines for commercial use. The following list, although not comprehensive, gives an indication of locations that are included in the scope: - public use areas such as hotels, schools, hospitals; - industrial locations, for example factories and manufacturing shops; - retail outlets, for example shops and supermarkets; - business premises, for example offices and banks; - rental services for those machines; - all uses other than normal housekeeping purposes. The following power systems are covered: - mains powered motors up to a rated voltage of 250 V for single-phase appliances and 480 V for other appliances, - battery-operated machines. This standard applies to machines in which the pressure of the employed cleaning agent does not exceed 2,5 MPa, and in which the product of the pressure (in MPa) and the flow of cleaning agent (in litres per minute) does not exceed 100, and in which the temperature of the cleaning agent at the spray nozzle outlet does not exceed 85 °C. This standard does not apply to - vacuum cleaners and water-suction cleaning appliances for household use (IEC 60335-2-2); - floor treatment machines for commercial use (IEC 60335-2-67, IEC 60335-2-72); - wet and dry vacuum cleaners, including power brush, for commercial use (IEC 60335-2-69); - hand-held and transportable motor-operated electric tools (IEC 60745 series, IEC 61029 series, IEC 62841 series). - machines designed for use in corrosive or explosive environments (dust, vapour or gas); - machines designed for picking up hazardous dusts (as defined in IEC 60335-2-69), inflammable substances, or glowing particles; - machines designed to handle hazardous solvents, such as flammable or explosive liquids;

Skaityti, komentuoti projektą Peržiūrėti metaduomenis

prEN IEC 60335-2-67:2026/prAA:2026 Viešoji apklausa

Komentavimo iki data 2026-11-08

Buitiniai ir panašios paskirties elektriniai prietaisai. Sauga. 2-67 dalis. Ypatingieji reikalavimai, keliami komercinės paskirties grindų priežiūros mašinoms

This standard deals with the safety of powered floor treatment machines intended for commercial indoor or outdoor use for the following applications: - scrubbing, - wet or dry pick-up, - polishing and dry buffing, - application of wax, sealing products and powder based detergents, - shampooing, - stripping, grinding and scarifying of floors with an artificial surface. These machines have a cleaning motion which is more lateral or periodic than linear. This standard applies to machines for commercial use. The following list, although not comprehensive, gives an indication of locations that are included in the scope: - public use areas such as hotels, schools, hospitals; - industrial locations, for example factories and manufacturing shops; - retail outlets, for example shops and supermarkets; - business premises, for example offices and banks; - all uses other than normal housekeeping purposes. These machines are not equipped with a traction drive. The following power systems are covered: - internal combustion engines, - mains powered motors up to a rated voltage of 250 V for single-phase appliances and 480 V for other appliances, - battery-operated machines. Battery-operated machines may be equipped with a built-in battery charger.

Skaityti, komentuoti projektą Peržiūrėti metaduomenis

Išplėstinė paieška

Rezultatai

Greitieji filtrai

Organizacija

Technikos komitetas

ICS

Būtini slapukai

Statistikos slapukai

El. pašto prenumerata

Standartų projektų sąrašas

Išplėstinė paieška

Rezultatai

Greitieji filtrai

Organizacija

Technikos komitetas

ICS