Standartų projektų sąrašas

prEN IEC 63053-2:2026 Viešoji apklausa

Komentavimo iki data 2026-04-22

Buitinės ir panašios paskirties liekamąja srove valdomi jungtuvai, skirti nuolatinės srovės sistemoms. 2 dalis. Liekamąja srove valdomi jungtuvai be integruotos apsaugos nuo viršsrovių

Skaityti, komentuoti projektą Peržiūrėti metaduomenis

prEN IEC 60061-PR2025-3:2026 Viešoji apklausa

Komentavimo iki data 2026-04-15

Lempų cokoliai ir lizdai su kalibrais pakeičiamumui ir saugai tikrinti. Pasiūlymas įtraukti į IEC 60061-3 GJ6.6d-2-x kalibrų rinkinį

Skaityti, komentuoti projektą Peržiūrėti metaduomenis

prEN IEC 62998-1:2026 Viešoji apklausa

Komentavimo iki data 2026-04-15

Mašinų sauga. Su sauga susiję jutikliai, naudojami žmonėms apsaugoti

Skaityti, komentuoti projektą Peržiūrėti metaduomenis

prEN IEC 61496-1:2026 Viešoji apklausa

Komentavimo iki data 2026-04-15

Mašinų sauga. Jutiklinė elektrinė apsauginė įranga. 1 dalis. Bendrieji reikalavimai ir bandymai

Skaityti, komentuoti projektą Peržiūrėti metaduomenis

prEN IEC 61496-2:2026 Viešoji apklausa

Komentavimo iki data 2026-04-15

Mašinų sauga. Jutiklinė elektrinė apsauginė įranga. 2 dalis. Ypatingieji reikalavimai, keliami įrangai su aktyviaisiais optoelektroniniais apsauginiais įtaisais

Skaityti, komentuoti projektą Peržiūrėti metaduomenis

prEN IEC 63533:2026 Viešoji apklausa

Komentavimo iki data 2026-04-15

Baktericidinė įranga. Ore esančių mikroorganizmų inaktyvinimas naudojant baktericidinius ultravioletinius šviestuvus

Skaityti, komentuoti projektą Peržiūrėti metaduomenis

prEN IEC 61009-2-1:2026/prAA:2026 Viešoji apklausa

Komentavimo iki data 2026-04-08

Buitiniai ir panašios paskirties liekamąja srove valdomi jungtuvai su integruota apsauga nuo viršsrovių. 2-1 dalis. Liekamąja srove valdomi jungtuvai su integruota apsauga nuo viršsrovių pagal 4.1.1 klasifikaciją

IEC 61009-1:2024, Clause 1 is applicable except for the first paragraph and the last paragraph, which are replaced by the following, respectively: This document applies to residual current operated circuit-breakers with integral overcurrent protection for household and similar uses (hereafter referred to as RCBOs), classified according to IEC 61009-1:2024, 4.1.1. RCBOs according to this document are intended for voltages not exceeding 440 V AC with frequencies of 50 Hz, 60 Hz or 50/60 Hz and currents not exceeding 125 A and rated short-circuit capacities not exceeding 25 000 A for operation at 50 Hz or 60 Hz. This document applies in conjunction with IEC 61009-1:2024. It specifies requirements, tests and test sequences to verify compliance and is used for certification purposes.

Skaityti, komentuoti projektą Peržiūrėti metaduomenis

prEN IEC 61008-2-1:2026/prAA:2026 Viešoji apklausa

Komentavimo iki data 2026-04-08

Buitiniai ir panašios paskirties liekamąja srove valdomi jungtuvai be integruotos apsaugos nuo viršsrovių. 2-1 dalis. Liekamąja srove valdomi jungtuvai be integruotos apsaugos nuo viršsrovių pagal 4.1.1 klasifikaciją

IEC 61008-1:2024, Clause 1 is applicable except for the first paragraph, which is replaced by the first paragraph below, and the last paragraph, which is replaced by the second paragraph below: This part of IEC 61008 applies to residual current operated circuit-breakers, without integral overcurrent protection, for household and similar uses (hereafter referred to as RCCBs), classified according to IEC 61008-1:2024, 4.1.1. RCCBs according to this document are intended for voltages not exceeding 440 V AC with frequencies of 50 Hz, 60 Hz or 50/60 Hz and currents not exceeding 125 A, intended principally for protection against shock hazard. This document applies in conjunction with IEC 61008-1:2024. It specifies requirements, tests and test sequences to verify compliance and is used for certification purposes.

Skaityti, komentuoti projektą Peržiūrėti metaduomenis

prEN IEC 61009-2-1:2026 Viešoji apklausa

Komentavimo iki data 2026-04-08

Buitiniai ir panašios paskirties liekamąja srove valdomi jungtuvai su integruota apsauga nuo viršsrovių. 2-1 dalis. Liekamąja srove valdomi jungtuvai su integruota apsauga nuo viršsrovių pagal 4.1.1 klasifikaciją

IEC 61009-1:2024, Clause 1 is applicable except for the first paragraph and the last paragraph, which are replaced by the following, respectively: This document applies to residual current operated circuit-breakers with integral overcurrent protection for household and similar uses (hereafter referred to as RCBOs), classified according to IEC 61009-1:2024, 4.1.1. RCBOs according to this document are intended for voltages not exceeding 440 V AC with frequencies of 50 Hz, 60 Hz or 50/60 Hz and currents not exceeding 125 A and rated short-circuit capacities not exceeding 25 000 A for operation at 50 Hz or 60 Hz. This document applies in conjunction with IEC 61009-1:2024. It specifies requirements, tests and test sequences to verify compliance and is used for certification purposes.

Skaityti, komentuoti projektą Peržiūrėti metaduomenis

prEN IEC 61008-2-1:2026 Viešoji apklausa

Komentavimo iki data 2026-04-08

Buitiniai ir panašios paskirties liekamąja srove valdomi jungtuvai be integruotos apsaugos nuo viršsrovių. 2-1 dalis. Liekamąja srove valdomi jungtuvai be integruotos apsaugos nuo viršsrovių pagal 4.1.1 klasifikaciją

IEC 61008-1:2024, Clause 1 is applicable except for the first paragraph, which is replaced by the first paragraph below, and the last paragraph, which is replaced by the second paragraph below: This part of IEC 61008 applies to residual current operated circuit-breakers, without integral overcurrent protection, for household and similar uses (hereafter referred to as RCCBs), classified according to IEC 61008-1:2024, 4.1.1. RCCBs according to this document are intended for voltages not exceeding 440 V AC with frequencies of 50 Hz, 60 Hz or 50/60 Hz and currents not exceeding 125 A, intended principally for protection against shock hazard. This document applies in conjunction with IEC 61008-1:2024. It specifies requirements, tests and test sequences to verify compliance and is used for certification purposes.

Skaityti, komentuoti projektą Peržiūrėti metaduomenis

prEN IEC 61009-1:2026/prAA:2026 Viešoji apklausa

Komentavimo iki data 2026-04-08

Buitiniai ir panašios paskirties liekamąja srove valdomi jungtuvai su integruota apsauga nuo viršsrovių. 1 dalis. Bendrosios taisyklės

This document gives general requirements and tests for residual current operated circuit-breakers with integral overcurrent protection for household and similar uses (hereafter referred to as RCBOs), for rated operational voltages not exceeding 440 V AC, with rated frequencies of 50 Hz, 60 Hz or 50/60 Hz and rated currents not exceeding 125 A and rated short-circuit capacities not exceeding 25 000 A. RCBOs are intended to provide fault protection (previously referred to as protection against indirect contact), the exposed conductive parts of the installation being connected to an appropriate earth electrode. These devices are also intended to protect against overcurrents in the wiring installations of buildings and similar applications. They are also intended to be used to provide protection against fire hazards due to a persistent earth fault current. RCBOs having a rated residual operating current not exceeding 30 mA are used for fault protection and additional protection in the case of failure of the protective provisions against electric shock. This document applies to RCBOs performing simultaneously the functions of detection of the residual current, of comparison of the value of this current with the residual operating value and of opening of the protected circuit when the residual current exceeds this value. These devices also perform the function of making, carrying and breaking overcurrents under specified conditions. RCBOs are intended to be operated by ordinary or uninstructed persons and designed not to require maintenance. The requirements of this document apply for standard conditions (see 7.1). Additional requirements can be necessary for RCBOs used in locations which have severe environmental conditions. RCBOs within the scope of this document are intended for use in an environment with pollution degree 2 (see 7.3). RCBOs are suitable for isolation. Special precautions (e.g. surge protective devices) can be necessary when excessive overvoltages are likely to occur on the supply side (for example in the case of supply through overhead lines, see IEC 60364-4-44 and IEC 60364-5-53). RCBOs, with the exception of those with an uninterrupted neutral, are suitable for use in IT systems. RCBOs of the general type are resistant to current surges, including the case where surge voltages (as a result of switching transients or induced by lightning) cause loading currents in the installation without occurrence of flashover. RCBOs of type S are considered to be sufficiently resistant against unwanted tripping even if the surge voltage causes a flashover and a follow-on current occurs. This document also applies to RCBOs obtained by the assembly of an adaptable residual current device with a circuit-breaker. The mechanical assembly is intended to be effected in the factory by the manufacturer, or on site, in which case the requirements of Annex G apply. It also applies to RCBOs having more than one rated current, provided that the means for changing from one discrete rating to another is not accessible in normal service and that the rating cannot be changed without the use of a tool. Particular requirements are necessary for RCBOs intended to be used at frequencies other than 50 Hz or 60 Hz. For RCBOs incorporated in, or intended for association with socket-outlets only, the requirements of this document can be used, as far as applicable, in conjunction with the requirements of IEC 60884-1 or the national requirements of the country where the product is placed on the market. This document does not apply to: ....

Skaityti, komentuoti projektą Peržiūrėti metaduomenis

prEN IEC 61008-1:2026/prAA:2026 Viešoji apklausa

Komentavimo iki data 2026-04-08

Buitiniai ir panašios paskirties liekamąja srove valdomi jungtuvai be integruotos apsaugos nuo viršsrovių. 1 dalis. Bendrosios taisyklės

This document gives general requirements and tests for residual current operated circuit-breakers without integral overcurrent protection for household and similar uses (hereafter referred to as RCCBs), for rated operational voltages not exceeding 440 V AC, with rated frequencies of 50 Hz, 60 Hz or 50/60 Hz and rated currents not exceeding 125 A, intended principally for protection against shock hazard. RCCBs are intended to provide fault protection (previously referred to as protection against indirect contact), the exposed conductive parts of the installation being connected to an appropriate earth electrode. They are also intended to be used to provide protection against fire hazards due to a persistent earth fault current. RCCBs having a rated residual operating current not exceeding 30 mA are used for fault protection and additional protection in the case of failure of the protective provisions against electric shock. This document applies to RCCBs performing simultaneously the functions of detection of the residual current, of comparison of the value of this current with the residual operating value and of opening of the protected circuit when the residual current exceeds this value. RCCBs are intended to be operated by ordinary or uninstructed persons and designed not to require maintenance. The requirements of this document apply for standard conditions (see 7.1). Additional requirements can be necessary for RCCBs used in locations which have severe environmental conditions. RCCBs within the scope of this document are intended for use in an environment with pollution degree 2 (see 7.3) and overvoltage category III. RCCBs are suitable for isolation. Special precautions (e.g. surge protective devices) can be necessary when excessive overvoltages are likely to occur on the supply side (for example in the case of supply through overhead lines, see IEC 60364-4-44 and IEC 60364-5-53). RCCBs are suitable for use in IT systems. RCCBs of the general type are resistant to current surges, including the case where surge voltages (as a result of switching transients or induced by lightning) cause loading currents in the installation without occurrence of flashover. RCCBs of type S are considered to be sufficiently resistant against unwanted tripping even if the surge voltage causes a flashover and a follow-on current occurs. Particular requirements are necessary for RCCBs intended to be used at frequencies other than 50 Hz or 60 Hz. For RCCBs incorporated in, or intended for association with socket-outlets only, the requirements of this document can be used, as far as applicable, in conjunction with the requirements of IEC 60884-1 or the national requirements of the country where the product is placed on the market. This document does not apply to: – RCCBs the current setting of which is adjustable without a tool; – RCCBs including batteries. This document is not intended to be used alone; it is intended to be used in conjunction with the relevant product standard, IEC 61008-2-1 or IEC 61008-2-2.

Skaityti, komentuoti projektą Peržiūrėti metaduomenis

prEN IEC 61009-1:2026 Viešoji apklausa

Komentavimo iki data 2026-04-08

Buitiniai ir panašios paskirties liekamąja srove valdomi jungtuvai su integruota apsauga nuo viršsrovių. 1 dalis. Bendrosios taisyklės

This document gives general requirements and tests for residual current operated circuit-breakers with integral overcurrent protection for household and similar uses (hereafter referred to as RCBOs), for rated operational voltages not exceeding 440 V AC, with rated frequencies of 50 Hz, 60 Hz or 50/60 Hz and rated currents not exceeding 125 A and rated short-circuit capacities not exceeding 25 000 A. RCBOs are intended to provide fault protection (previously referred to as protection against indirect contact), the exposed conductive parts of the installation being connected to an appropriate earth electrode. These devices are also intended to protect against overcurrents in the wiring installations of buildings and similar applications. They are also intended to be used to provide protection against fire hazards due to a persistent earth fault current. RCBOs having a rated residual operating current not exceeding 30 mA are used for fault protection and additional protection in the case of failure of the protective provisions against electric shock. This document applies to RCBOs performing simultaneously the functions of detection of the residual current, of comparison of the value of this current with the residual operating value and of opening of the protected circuit when the residual current exceeds this value. These devices also perform the function of making, carrying and breaking overcurrents under specified conditions. RCBOs are intended to be operated by ordinary or uninstructed persons and designed not to require maintenance. The requirements of this document apply for standard conditions (see 7.1). Additional requirements can be necessary for RCBOs used in locations which have severe environmental conditions. RCBOs within the scope of this document are intended for use in an environment with pollution degree 2 (see 7.3). RCBOs are suitable for isolation. Special precautions (e.g. surge protective devices) can be necessary when excessive overvoltages are likely to occur on the supply side (for example in the case of supply through overhead lines, see IEC 60364-4-44 and IEC 60364-5-53). RCBOs, with the exception of those with an uninterrupted neutral, are suitable for use in IT systems. RCBOs of the general type are resistant to current surges, including the case where surge voltages (as a result of switching transients or induced by lightning) cause loading currents in the installation without occurrence of flashover. RCBOs of type S are considered to be sufficiently resistant against unwanted tripping even if the surge voltage causes a flashover and a follow-on current occurs. This document also applies to RCBOs obtained by the assembly of an adaptable residual current device with a circuit-breaker. The mechanical assembly is intended to be effected in the factory by the manufacturer, or on site, in which case the requirements of Annex G apply. It also applies to RCBOs having more than one rated current, provided that the means for changing from one discrete rating to another is not accessible in normal service and that the rating cannot be changed without the use of a tool. Particular requirements are necessary for RCBOs intended to be used at frequencies other than 50 Hz or 60 Hz. For RCBOs incorporated in, or intended for association with socket-outlets only, the requirements of this document can be used, as far as applicable, in conjunction with the requirements of IEC 60884-1 or the national requirements of the country where the product is placed on the market. This document does not apply to: .........

Skaityti, komentuoti projektą Peržiūrėti metaduomenis

prEN IEC 61008-1:2026 Viešoji apklausa

Komentavimo iki data 2026-04-08

Buitiniai ir panašios paskirties liekamąja srove valdomi jungtuvai be integruotos apsaugos nuo viršsrovių. 1 dalis. Bendrosios taisyklės

This document gives general requirements and tests for residual current operated circuit-breakers without integral overcurrent protection for household and similar uses (hereafter referred to as RCCBs), for rated operational voltages not exceeding 440 V AC, with rated frequencies of 50 Hz, 60 Hz or 50/60 Hz and rated currents not exceeding 125 A, intended principally for protection against shock hazard. RCCBs are intended to provide fault protection (previously referred to as protection against indirect contact), the exposed conductive parts of the installation being connected to an appropriate earth electrode. They are also intended to be used to provide protection against fire hazards due to a persistent earth fault current. RCCBs having a rated residual operating current not exceeding 30 mA are used for fault protection and additional protection in the case of failure of the protective provisions against electric shock. This document applies to RCCBs performing simultaneously the functions of detection of the residual current, of comparison of the value of this current with the residual operating value and of opening of the protected circuit when the residual current exceeds this value. RCCBs are intended to be operated by ordinary or uninstructed persons and designed not to require maintenance. The requirements of this document apply for standard conditions (see 7.1). Additional requirements can be necessary for RCCBs used in locations which have severe environmental conditions. RCCBs within the scope of this document are intended for use in an environment with pollution degree 2 (see 7.3). RCCBs are suitable for isolation. Special precautions (e.g. surge protective devices) can be necessary when excessive overvoltages are likely to occur on the supply side (for example in the case of supply through overhead lines, see IEC 60364-4-44 and IEC 60364-5-53). RCCBs, with the exception of those with an uninterrupted neutral, are suitable for use in IT systems. RCCBs of the general type are resistant to current surges, including the case where surge voltages (as a result of switching transients or induced by lightning) cause loading currents in the installation without occurrence of flashover. RCCBs of type S are considered to be sufficiently resistant against unwanted tripping even if the surge voltage causes a flashover and a follow-on current occurs. Particular requirements are necessary for RCCBs intended to be used at frequencies other than 50 Hz or 60 Hz. For RCCBs incorporated in, or intended for association with socket-outlets only, the requirements of this document can be used, as far as applicable, in conjunction with the requirements of IEC 60884-1 or the national requirements of the country where the product is placed on the market. This document does not apply to: – RCCBs the current setting of which is adjustable without a tool; – RCCBs including batteries. This document is not intended to be used alone; it is intended to be used in conjunction with the relevant product standard, IEC 61008-2-1 or IEC 61008-2-2.

Skaityti, komentuoti projektą Peržiūrėti metaduomenis

prEN IEC 60695-11-2:2026 Viešoji apklausa

Komentavimo iki data 2026-04-01

Gaisrinio pavojingumo bandymai. 11-2 dalis. Bandymo liepsnos. 1 kW galios paruošto mišinio liepsna. Aparatūra, patvirtinamojo bandymo tvarka ir nurodymai

Skaityti, komentuoti projektą Peržiūrėti metaduomenis

EN IEC 61442:2024/prA1:2026 Viešoji apklausa

Komentavimo iki data 2026-04-01

Vardinės nuo 6 kV (Um = 7,2 kV) iki 30 kV (Um = 36 kV) įtampos galios kabelių pagalbinių reikmenų bandymo metodai

Skaityti, komentuoti projektą Peržiūrėti metaduomenis

prEN 50191:2026 Viešoji apklausa

Komentavimo iki data 2026-04-01

Elektrinės bandymų įrangos įrengimas ir naudojimas

1.1 This document is applicable to the installation and operation of fixed and temporary electrical test installations. 1.2 Compliance with this document needs to be applied, if contact with live parts presents dangerous. This is the case when: a) the voltage exceeds 25 V AC (frequencies lower than 500 Hz) or 60 V DC and current exceeds 3 mA for AC or 12 mA for DC, or b) the voltage exceeds 25 V AC (for any frequency) or 60 V DC and the discharge energy of the test station and test object exceeds 350 mJ, or c) at frequencies above 500 Hz the national determined current and voltage values are applied. If there are no national requirements, determined reference values for permissible body currents and contact voltages can be taken from Table A.1; This document is applicable even if conditions a) to c) are fulfilled, due to other possible risks, e.g. risk of fire or explosion. NOTE The values for the resultant current of 3 mA AC or 12 mA DC comply with the information about the effects of current on human beings and livestock in IEC/TS 60479 1. 1.3 Some specifications in this document refer to a voltage value of 1 000 V. This value applies to AC voltages and is equated to a value of 1 500 V DC voltage. 1.4 Where no requirements are given in this document, the documents of the HD 60364 series (for nominal voltages up to 1 000 V) or EN IEC 61936 1 and EN 50522 (for nominal voltages exceeding 1 kV) apply to the installation of electrical test installations and EN 50110 1 applies to the operation of electrical test installations. 1.5 This document does not apply to the power supply to the test installations. In this case, the documents of the HD 60364 series (for nominal voltages up to 1 000 V) or EN IEC 61936 1 (for nominal voltages exceeding 1 kV) apply to their installation and EN 50110 1 applies to their operation.

Skaityti, komentuoti projektą Peržiūrėti metaduomenis

EN IEC 62115:2020/prAB:2026 Viešoji apklausa

Komentavimo iki data 2026-03-25

Elektriniai žaislai. Sauga

The standard deals with safety requirements for electric toys that have at least one function dependant on electricity, electric toys being any product designed or intended, whether or not exclusively, for use in play by children under 14 years of age.

Skaityti, komentuoti projektą Peržiūrėti metaduomenis

prEN IEC 60695-5-2:2026 Viešoji apklausa

Komentavimo iki data 2026-03-25

Gaisrinio pavojingumo bandymai. 5-2 dalis. Lakiųjų gaisro produktų sukeliamos korozinės pažaidos. Trumpa bandymo metodų apžvalga ir tinkamumas

Skaityti, komentuoti projektą Peržiūrėti metaduomenis

prEN IEC 60669-2-1:2026 Viešoji apklausa

Komentavimo iki data 2026-03-25

Buitinių ir panašios paskirties stacionariųjų elektros įrenginių jungikliai. 2-1 dalis. Ypatingieji reikalavimai. Elektroniniai vadymo įtaisai

Skaityti, komentuoti projektą Peržiūrėti metaduomenis

EN 62841-1:2015/prAC:2026 Viešoji apklausa

Komentavimo iki data 2026-03-18

Elektriniai varikliniai rankiniai įrankiai, kilnojamieji įrankiai ir vejų bei sodų mašinos. Sauga. 1 dalis. Bendrieji reikalavimai

Skaityti, komentuoti projektą Peržiūrėti metaduomenis

prEN IEC 63116:2025 Archyvuotas

Komentavimo iki data 2026-02-25

Apšvietimo sistemos. Bendrieji reikalavimai

Peržiūrėti metaduomenis

Išplėstinė paieška

Rezultatai

Greitieji filtrai

Organizacija

Technikos komitetas

ICS

Būtini slapukai

Statistikos slapukai

El. pašto prenumerata

Standartų projektų sąrašas

Išplėstinė paieška

Rezultatai

Greitieji filtrai

Organizacija

Technikos komitetas

ICS