GDPR

projektai-lsd Lithuanian Standards Board
Portal for draft standards

Extended search

till

Results

Showing:
EN 1999-1-1:2023/prA1 Public enquiry
Comment end date 2026-05-28
Eurocode 9 - Design of aluminium structures - Part 1-1: General rules

EN 1999-1-1 gives basic design rules for structures made of wrought aluminium alloys and limited guidance for cast alloys (see Clause 5 and Annex C). This document does not cover the following, unless otherwise explicitly stated in this document: - members with material thickness less than 0,6 mm; - welded members with material thickness less than 1,5 mm; - connections with: - steel bolts and pins with diameter less than 5 mm; - aluminium bolts and pins with diameter less than 8 mm; - rivets and thread forming screws with diameter less than 3,9 mm.

EN 1999-1-2:2023/prA1 Public enquiry
Comment end date 2026-05-28
Eurocode 9 - Design of aluminium structures - Part 1-2: Structural fire design

1.1 Scope of EN 1999-1-2 (1) EN 1999-1-2 deals with the design of aluminium structures for the accidental situation of fire exposure and is intended to be used in conjunction with EN 1999-1-1, EN 1999-1-2, EN 1999-1-3, EN 1999-1-4 and EN 1999-1-5. This document only identifies differences from, or supplements to, normal temperature design. (2) EN 1999-1-2 applies to aluminium structures required to fulfil a load bearing function. (3) EN 1999-1-2 gives principles and application rules for the design of structures for specified requirements in respect of the aforementioned function and the levels of performance. (4) EN 1999-1-2 applies to structures, or parts of structures, that are within the scope of EN 1999 1 1 and are designed accordingly. (5) The methods given in EN 1999-1-2 are applicable to the following aluminium alloys: EN AW-3004 - H34 EN AW-5083 - O and H12 EN AW-6063 - T5 and T6 EN AW-5005 - O and H34 EN AW-5454 - O and H34 EN AW-6082 - T4 and T6 EN AW-5052 - H34 EN AW-6061 - T6 (6) The methods given in EN 1999-1-2 are applicable also to other aluminium alloy/tempers of EN 1999 1-1, if reliable material properties at elevated temperatures are available or the simplified assumptions in 5.2.1 are applied. 1.2 Assumptions (1) In addition to the general assumptions of EN 1990, the following assumptions apply: - the choice of the relevant design fire scenario is made by appropriate qualified and experienced personnel, or is given by the relevant national regulation. - any active and passive fire protection systems taken into account in the design will be adequately maintained. (2) EN 1999 is intended to be used in conjunction with: - European Standards for construction products relevant for aluminium structures - EN 1090-1, Execution of steel structures and aluminium structures - Part 1: Requirements for conformity assessment of structural components - EN 1090-3, Execution of steel structures and aluminium structures - Part 3: Technical requirements for aluminium structures

EN 1999-1-4:2023/prA1 Public enquiry
Comment end date 2026-05-28
Eurocode 9 - Design of aluminium structures - Part 1-4: Cold-formed structural sheeting

1.1 Scope of EN 1999-1-4 (1) EN 1999-1-4 gives design requirements for cold-formed trapezoidal aluminium sheeting. It applies to cold-formed aluminium products made from hot rolled or cold rolled sheet or strip that have been cold-formed by such processes as cold-rolled forming or press-breaking. NOTE 1 The rules in this part complement the rules in other parts of EN 1999-1. NOTE 2 The execution of aluminium structures made of cold-formed structures for roof, ceiling, floor and wall applications is covered in EN 1090-5. (2) EN 1999-1-4 gives methods for stressed-skin design using aluminium sheeting as a structural diaphragm. (3) EN 1999-1-4 does not apply to cold-formed aluminium profiles like C- and Z- profiles nor cold-formed and welded circular or rectangular hollow sections. (4) EN 1999-1-4 gives methods for design by calculation and for design assisted by testing. The methods for the design by calculation apply only within stated ranges of material properties and geometrical properties for which sufficient experience and test evidence is available. These limitations do not apply to design by testing. (5) EN 1999-1-4 does not cover load arrangement for loads during execution and maintenance. 1.2 Assumptions (1) For the design of new structures, EN 1999 is intended to be used, for direct application, together with EN 1990, EN 1991, EN 1992, EN 1993, EN 1994, EN 1995, EN 1997 and EN 1998. EN 1999 is intended to be used in conjunction with: - European Standards for construction products relevant for aluminium structures; - EN 1090-1, Execution of steel structures and aluminium structures - Part 1: Requirements for conformity assessment of structural components; - EN 1090-5, Execution of steel structures and aluminium structures - Part 5: Technical requirements for cold-formed structural aluminium elements and cold-formed structures for roof, ceiling, floor and wall applications.

Quick filters

Technical Committee
TK 1 Electronics (8) TK 4 Information technology (2) TK 5 Electrical engineering (25) TK 8 Electromagnetic compatibility (2) TK 12 Motor - roads (4) TK 13 Agricultural engineering (9) TK 18 Telecommunications (15) TK 19 Concrete and reinforced concrete (1) TK 20 Toys, child use articles, sports and other recreational equipment (1) TK 21 Textiles and personal protective equipment (2) TK 22 Fire safety (3) TK 23 Ceramic tiles, masonry and natural stones (2) TK 28 Gas systems (4) TK 29 Water supply (3) TK 32 Health (11) TK 34 Metrology (2) TK 35 Safety of machinery (1) TK 36 Environmental protection (7) TK 38 Building constructions (26) TK 40 Petroleuml, petroleum products, lubricants and alternative fuels (1) TK 41 Welding (2) TK 42 Packaging (1) TK 43 Railway traffic (3) TK 45 Electric power (17) TK 47 Information and documentation (3) TK 49 Metallic materials (6) TK 50 Heating and Ventilation Systems (1) TK 51 Food analysis- Horizontal methods (1) TK 54 Assistive products for persons with disability (1) TK 57 Fertilizers (5) TK 59 Geotechnics (3) TK 63 Gas cylinders and cryogenic vessels (3) TK 65 Tourism services (1) TK 66 Non-destructive testing (1) TK 68 Plastics (3) TK 70 Pulp, paper, board, adhesives (1) TK 71 Sustainably produced biomass for energy application, solid biofuel and solid recovered fuel (1) TK 76 Explosive atmospheres (2) TK 77 Lifts (1) TK 79 IT security techniques (1) TK 82 Safety of trackless overground vehicles (2) TK 84 Chimneys and solid fuel burning appliances (2) TK 86 Geographic information (1) TK 88 Building Information Modelling (BIM) (2) TK 89 Risk management and organizational governance (2) TK 91 Asset management and technical maintenance (1) TK 99 Health Informatics (3)
ICS
Fizikinės dirvožemio savybės (1) Agricultural machines and equipment in general (1) Agricultural tractors and trailed vehicles (1) Aircraft and space vehicles in general (1) Alkaline secondary cells and batteries (1) Aluminium products (3) Aluminium structures (3) Application of information technology in general (1) Automatic controls for household use (2) Binders. Sealing materials (4) Bolts, screws, studs (5) Bridge construction (1) Cement. Gypsum. Lime. Mortar (1) Check valves (1) Chemical laboratories. Laboratory equipment (3) Chimneys, shafts, ducts (1) Civil engineering in general (1) Cleaning appliances (2) Coatings and related processes used in aerospace industry (2) Company organization and management in general (1) Concrete and concrete products (2) Connecting devices (1) Construction industry in general (1) Cooking ranges, working tables, ovens and similar appliances (2) Cookware, cutlery and flatware (1) Corrosion of metals (1) Dental equipment (1) Dental instruments (1) Dental materials (1) Dentistry in general (1) Dishwashers (1) Domestic refrigerating appliances (2) Domestic safety (11) Earthworks. Excavations. Foundation construction. Underground works (2) Electric heaters (2) Electrical and electronic equipment (2) Electrical and electronic testing (1) Electrical apparatus for explosive atmospheres (2) Electrical insulation in general (1) Environmental impact assessment (1) Environmental testing (2) Equipment for storage, preparation and distribution of fertilizers (1) Ergonomics (1) Examination of physical properties of water (1) Exploratory, drilling and extraction equipment (1) Explosives. Pyrotechnics and fireworks (1) Extraction and processing of petroleum and natural gas (2) Fasteners in general (1) Fertilizers (5) Fibre optic interconnecting devices (2) Fibres and cables (2) Fire protection (2) Fissile materials and nuclear fuel technology (4) Floor coverings (2) Flow in open channels (1) Gas cylinders (2) Gas supply systems (1) General methods of tests and analysis for food products (2) General purpose pallets (1) Governance and ethics (1) Harvesting equipment (1) Heat pumps (1) Immunity (2) Indoor sports equipment (1) Industrial process measurement and control (1) Information technology (IT) in general (1) Installations and equipment for waste disposal and treatment (1) Insulating materials in general (1) Iron and steel forgings (1) Iron and steel products in general (1) IT applications in health care technology (3) IT applications in science (1) IT applications in transport (2) IT Security (3) Laboratory medicine in general (1) Lamps in general (2) Laundry appliances (1) Leather and furs (2) Lifts. Escalators (1) Liquid fuels (1) Luminaires (1) Management of human resources (1) Masonry (1) Materials and components for railway engineering (1) Measurement of electrical and magnetic quantities (2) Measurement of volume, mass, density, viscosity (1) Mechanical structures for electronic equipment (2) Mechanical testing of metals (2) Medical microbiology (1) Metallurgy (Vocabularies) (1) Microbiology of water (1) Mineral materials and products (2) Natural gas (1) Navigation and control equipment (1) Noise emitted by machines and equipment (1) Non-destructive testing (1) Nuclear power plants. Safety (1) Nuts (6) Other equipment related to power transmission and distribution networks (2) Other products of the chemical industry (1) Other semiconductor devices (1) Other standards related to aids for disabled and handicapped people (1) Paints and varnishes (1) Paper and board (1) Passenger and cabin equipmen (2) Petroleum products and natural gas handling equipment (2) Pipeline components and pipelines in general (1) Pipelines and its parts for external sewage systems (1) Plastics in general (1) Plastics pipes and fittings for non fluid use (1) Pneumatic tools (1) Pollution, pollution control and conservation (2) Postal services (1) Power transmission and distribution lines (3) Products of the chemical industry (1) Protection against dangerous goods (1) Radiation measurements (2) Railway rolling stock in general (2) Raw skins, hides and pelts (1) Recycling (1) Rotating machinery in general (1) Seismic and vibration protection (1) Services in general (1) Solar energy engineering (1) Solid fuel heaters (1) Solid fuels (1) Steel pipes and tubes for specific use (2) Steel structures (1) Surface treatment and coating in general (1) Syringes, needles and catheters (1) Technical aspects (16) TELECOMMUNICATIONS. AUDIO AND VIDEO ENGINEERING (15) Telecontrol. Telemetering (5) Thermistors (1) Timber structures (1) Trailing stock (1) Transport by rail (1) Walls. Partitions. Façades (1) Water heating equipment (2) Waxes, bituminous materials and other petroleum products (1) Welding equipment (2) Woodworking machines (2) Workplace atmospheres (1) Writing and transliteration (3)