GDPR

projektai-lsd Lithuanian Standards Board
Portal for draft standards

Extended search

till

Results

Showing:
Total records found: 159
1 2 3 … 7 arrow-next
EN 18052:2025/prA1 Public enquiry
Comment end date 2026-12-06
Intelligent transport systems - ESafety - ECall end to end conformance testing for eCall HLAP in hybrid circuit switched/packet switched network environments

This document describes the key actors in the eCall chain of service provision in hybrid circuit switched/packet switched network environments as: 1) In-Vehicle System (IVS)/vehicle, 2) Mobile Network Operator (MNO), 3) Public Safety Answering Point (PSAP), and to provide conformance tests for actor groups 1) – 3). NOTE 1 Conformance tests are not appropriate nor required for vehicle occupants, although they are the recipient of the service. NOTE 2 Third party eCall systems (TPS-eCall) are not within the scope of this deliverable. This is because the core TPS-eCall standard (EN 16102) does not specify the communications link between the vehicle and the TPS service provider. NOTE 3 These conformance tests are partly based on the appropriate conformance tests from EN 16454 and CEN/prEN 17240. This deliverable therefore adapts and revises Conformance Test Protocols (CTP) from EN 16454 and CEN/prEN 17240 for hybrid circuit switched/packet switched network environments. This document complements EN 16454 and CEN/prEN 17240 and provides a suite of conformance tests for IVS equipment, MNOs and PSAPs, required to ensure and demonstrate compliance with CEN/prEN 17905. The scope covers conformance testing of new engineering developments, products and systems, and does not imply testing associated with individual installations in vehicles or locations.

prEN 3682-001 Public enquiry
Comment end date 2026-12-05
Aerospace series - Connectors, plug and receptacle, electrical, rectangular, interchangeable insert type, rack to panel, operating temperature 150 °C continuous - Part 001: Technical specification

This document specifies the general characteristics, the conditions for qualification, acceptance and quality assurance, as well as the test programs and groups for connectors intended for use in a temperature range from - 65 °C to 150 °C continuous.

prEN 3682-002 Public enquiry
Comment end date 2026-12-05
Aerospace series - Connectors, plug and receptacle, electrical, rectangular, interchangeable insert type, rack to panel, operating temperature 150 °C continuous - Part 002: Specification of performance and contact arrangements
prEN 12814-3 Public enquiry
Comment end date 2026-12-06
Testing of welded joints in thermoplastics semi-finished products - Part 3: Tensile creep test

This document specifies the dimensions, the method of sampling, the preparation of the test specimens and the conditions for performing the tensile creep test perpendicular to the weld in order to determine the long-term tensile welding factor. A tensile creep test may be used in conjunction with other tests (e.g. bend test, tensile test, macrographic examination, …) to assess the performance of welded assemblies made from thermoplastics materials. The test is applicable to welded assemblies made from thermoplastics materials, filled or unfilled such as tubes and fittings, sheets, plates and profiles, but not reinforced, irrespective of the welding process used.

prEN 15182-3 Public enquiry
Comment end date 2026-12-05
Portable equipment for projecting extinguishing agents and firefighting support operations — Hand-held branchpipes for fire service use — Part 3: Smooth bore and/or one fixed spray jet angle branchpipes PN 16

In addition to the common requirements given in EN 15182-1, this document specifies the specific safety and performance requirements and the corresponding test methods, applicale to hand-held branchpipes with smooth bore and/or one fixed spray jet angle with a nominal pressure of 16 bar (1,6 MPa) PN 16, with a maximum flow rate up to 1 000 l/min at a reference pressure of 6 bar (0,6 MPa). NOTE 1 These branchpipes offer no or inadequate protection for firefighters when the spray jet angle is less than 30 ° and therefore are not adapted in high risk firefighting situations such as internal attack. NOTE 2 These branchpipes are not adapted when fighting fires in or near electrical installations when the spray jet angle is less than 30° without written authorization in the manual (safety distances included).

prEN 15182-2 Public enquiry
Comment end date 2026-12-05
Portable equipment for projecting extinguishing agents and firefighting support operations - Hand-held branchpipes for fire service use - Part 2: Combination branchpipes PN 16

In addition to the common requirements given in EN 15182 1, this document specifies the specific safety and performance requirements and the corresponding test methods, applicable to hand-held combination branchpipes (nozzles), with a nominal pressure of 16 bar (1,6 MPa) PN 16, with a maximum flow rate up to 1 000 l/min at a reference pressure of 6 bar (0,6 MPa).

prEN 15182-4 Public enquiry
Comment end date 2026-12-05
Portable equipment for projecting extinguishing agents and firefighting support operations — Hand-held branchpipes for fire service use — Part 4: High pressure branchpipes PN 40

In addition to common the requirements given in EN 15182 1, this document specifies the specific safety and performance requirements and the corresponding test methods, applicable to hand-held high pressure branchpipes (nozzles) with a nominal pressure of 40 bar (4,0 MPa) PN 40, with a maximum flow rate up to 250 l/min at a reference pressure of 6 bar (0,6 MPa). These branchpipes are used for example for quick attack lines, building fires, forest fires, etc.

prEN 15182-1 Public enquiry
Comment end date 2026-12-05
Portable equipment for projecting extinguishing agents and firefighting support operations — Hand-held branchpipes for fire service use — Part 1: Common requirements

This document specifies the minimum common safety and performance requirements of hand-held branchpipes used by fire and rescue service equipment. This document defines: - test methods; - classification and designation; - instructions for use and maintenance; marking. NOTE The additional specific requirements applicable to hand-held branchpipes are defined in EN 15182-2:— (combination branchpipes PN 16), EN 15182-3:— (Smooth bore and/or one fixed spray jet angle branchpipes PN 16) and EN 15182-4:— (High pressure branchpipes PN 40). This document is not applicable to: - branchpipes covered by the EN 671 series; - foam branchpipes covered by EN 16712-3; - CAFS branchpipes; - powder branchpipes; - branchpipes with a maximum working pressure above 40 bar.

prEN 13497 Public enquiry
Comment end date 2026-12-05
Thermal insulation products for building applications - Determination of the resistance to impact of external thermal insulation composite systems (ETICS)

This document specifies the equipment and procedure for determining the resistance to impact of ETICS kits with renders.

prEN ISO 14644-7 Public enquiry
Comment end date 2026-12-03
Cleanrooms and associated controlled environments - Part 7: Separative devices (ISO/DIS 14644-7:2026)

ISO 14644-7:2004 specifies the minimum requirements for the design, construction, installation, test and approval of separative devices, in those respects where they differ from cleanrooms as described in ISO 14644-4 and 14644-5. The application of ISO 14644-7:2004 takes into account the following limitations: user requirements are as agreed by customer and supplier; application-specific requirements are not addressed; specific processes to be accommodated in the separative-device installation are not specified; fire, safety and other regulatory matters are not considered specifically; where appropriate, national and local regulations apply. ISO 14644-7:2004 is not applicable to full-suits.

prEN ISO 8339 Public enquiry
Comment end date 2026-12-03
Building and civil engineering sealants - Determination of tensile properties (Extension to break) (ISO/DIS 8339:2026)

ISO 8339:2005 specifies a method for the determination of the tensile properties of sealants used in joints in building construction.

prEN 16883 Public enquiry
Comment end date 2026-12-03
Conservation of cultural heritage - Guidelines for improving the energy performance of historic buildings

This document provides guidelines for sustainably improving the energy performance of historic buildings, e.g. historically, architecturally or culturally valuable buildings, while respecting their significance. The use of this document is not limited to buildings with statutory heritage designation, it applies to historic buildings of all types and ages. This document presents a normative working procedure for selecting measures to improve energy performance, based on an investigation, analysis and documentation of the building including its significance. The procedure assesses the impact of those measures in relation to preserving the character-defining elements of the building.

prEN 438-2 Public enquiry
Comment end date 2026-11-30
High-pressure decorative laminates (HPL) - Sheets based on thermosetting resins (usually called laminates) - Part 2: Determination of properties

This document specifies the methods of test for determination of the properties of high-pressure decorative laminates as defined in Clause 3. These methods are primarily intended for testing the sheets specified in EN 438-3, EN 438-4, EN 438-5, EN 438-6, EN 438-8, and EN 438-9. The precision of the test methods, specified in this document, is not known because inter-laboratory data are not yet available. When inter-laboratory data will be obtained, precision statements will be added to the test method at the following revision. For those test methods having an end point determination based on subjective judgement, it is not meaningful to make a statement of precision.

prEN 12909 Public enquiry
Comment end date 2026-11-30
Products used for treatment of water intended for human consumption - Anthracite

This document is applicable to anthracite used for treatment of water intended for human consumption. This document describes the characteristics of anthracite and specifies the requirements and the corresponding test methods for anthracite. This document gives information on the use of anthracite in water treatment.

EN 16611:2023/prA1 Public enquiry
Comment end date 2026-11-28
Furniture - Assessment of the surface resistance to microscratching

This document specifies a method for the assessment of the surface resistance to microscratching and relates to rigid surfaces of all finished products, considering the following exceptions: - Method A is suitable for all types of surface coatings and coverings except for lacquers with pearly or metallic effects. - Method B is suitable for all types of surface. - No method applies to finishes on leather and fabrics. This document is applicable to the test intended to be carried out on a part of finished furniture, but it can be carried out on test panels of the same material, finished in an identical manner to the finished product, and of a size sufficient to meet the requirements of the test. It is essential that the test be carried out on unused surfaces.

EN 10205:2024/prA1 Public enquiry
Comment end date 2026-12-06
Cold reduced tinmill products - Blackplate

This document specifies requirements for blackplate product in the form of coils intended for direct use and mostly for the production of electrolytically zinc coated plate, or coils electrolytically coated with either tin (tinplate) or chromium/chromium oxide (ECCS or ECCS-RC). Blackplate can be a single or double reduced product and is specified in nominal thicknesses that are multiples of 0,005 mm from typical 0,10 mm up to 0,60 mm. This document applies to coils in nominal minimum widths of 600 mm. In addition to this document, the general technical delivery conditions of EN 10021 apply. NOTE Standard width coils for specific uses, e.g. tab stock, can be slit into narrow strip for supply in coil form.

prEN 12915-2 Public enquiry
Comment end date 2026-12-06
Products used for the treatment of water intended for human consumption - Granular activated carbon - Part 2: Reactivated granular activated carbon

This document is applicable to reactivated granular activated carbon used for treatment of water intended for human consumption. This document describes the characteristics of reactivated granular activated carbon and specifies the requirements and the corresponding test methods for reactivated granular activated carbon. This document gives information on the use of reactivated granular activated carbon in water treatment.

prEN ISO 3821 Public enquiry
Comment end date 2026-11-26
Gas welding equipment - Rubber hoses for welding, cutting and allied processes (ISO/DIS 3821:2026)

This document specifies requirements for rubber hoses (including twin hoses) for welding, cutting and allied processes. This document specifies requirements for rubber hoses for normal duty of 2 MPa (20 bar) and light duty [limited to hoses for maximum working pressure of 1 MPa (10 bar) and with bore up to and including 6,3 mm]. This document applies to hoses operated at temperatures −20 °C to +60 °C and used in: — gas welding and cutting; — arc welding under the protection of an inert or active gas; — processes allied to welding and cutting, in particular, heating, brazing, and metallization. This document does not specify requirements for hose assemblies; these are detailed in ISO 8207. This document applies neither to thermoplastics hoses nor to hoses used for high pressure [>0,15 MPa (>1,5 bar)] acetylene.

prEN ISO 5359 Public enquiry
Comment end date 2026-11-26
Anaesthetic and respiratory equipment - Low-pressure hose assemblies for use with medical gases (ISO/DIS 5359:2026)

ISO 5359:2014 specifies requirements for low-pressure hose assemblies intended for use with the following medical gases: oxygen, nitrous oxide, medical air, helium, carbon dioxide, xenon, specified mixtures of the gases listed above, oxygen-enriched air, air for driving surgical tools, nitrogen for driving surgical tools, and for use with vacuum. It applies to hose assemblies operating at pressures up to 1 400 kPa and for vacuum systems at pressures not greater than 60 kPa absolute. It does not specify the dimensions and allocation of the gas-specific inlet and outlet connectors for the hose assemblies.It does not specify requirements for coaxial hoses used for the supply and removal of air for driving surgical tools.Nor does it specify the intended uses of hose assemblies.

prEN ISO 18082 Public enquiry
Comment end date 2026-11-26
Anaesthetic and respiratory equipment - Dimensions of non-interchangeable screw-threaded (NIST) low-pressure connectors for medical gases (ISO/DIS 18082:2026)

ISO 18082:2014 specifies the dimensions, the allocation and marking of non-interchangeable screw-threaded (NIST) connectors intended to be used at operating pressures up to 1 400 kPa, and for vacuum systems at pressures not greater than 60 kPa absolute. ISO 18082:2014 specifies NIST connectors intended for use with the following medical gases: oxygen; nitrous oxide; medical air; helium; carbon dioxide; xenon; specified mixtures of the gases listed above; oxygen-enriched air; air for driving surgical tools; nitrogen for driving surgical tools; use with vacuum.

prEN ISO 9094 Public enquiry
Comment end date 2026-11-26
Small craft - Fire protection (ISO/DIS 9094:2026)

This document defines a practical degree of fire prevention and protection intended to provide enough time for occupants to escape a fire on board small craft. It applies to small craft having a length of the hull (LH) of up to 24 m except for personal watercraft. This document does not cover: —    the design and installation of permanently installed galley stoves and heating appliances (including components used to distribute the heat) using fuels that are liquid at atmospheric pressure on small craft, which are covered by ISO 14895:2016; —    carbon monoxide detecting systems, which are covered by ISO 12133.

prEN ISO 25178-3 Public enquiry
Comment end date 2026-11-26
Geometrical product specifications (GPS) - Surface texture: Areal - Part 3: Specification operators (ISO/DIS 25178-3:2026)

This part of ISO 25178 specifies the complete specification operator for surface texture (scale limited surfaces) by areal methods.

prEN 1127-2 Public enquiry
Comment end date 2026-11-26
Explosive atmospheres - Explosion prevention and protection - Part 2: Basic concepts and methodology for mining

This document specifies methods for explosion prevention and protection in mining by outlining the basic concepts and methodology for the design and construction of equipment, protective systems and components. This document applies to Group I equipment, protective systems and components intended for use in underground parts of mines and those parts of their surface installations at risk from firedamp and/or combustible dust. NOTE Detailed information on specific equipment, protective systems and components is contained in the relevant individual standards. Safety-relevant data regarding flammable materials and explosive atmospheres are required for the design and construction of the explosion protection measures. This document specifies methods for the identification and assessment of hazardous situations that may lead to explosions and describes the design and construction measures appropriate for the required safety. This is achieved by: — risk assessment; — risk reduction. The safety of equipment, protective systems, and components can be achieved by eliminating hazards and/or limiting the risk, i.e.: a) by appropriate design (without using safeguarding); b) by safeguarding; c) by information for use; d) by any other preventive measures. Measures in accordance with a) (prevention) and b) (protection) against explosions are dealt with in Clause 6 of this document; measures according to c) against explosions are dealt with in Clause 7 of this document. Measures in accordance with d) are not described in this document. They are dealt with in EN ISO 12100:2010, Clause 6. The preventive and protective measures described in this document will not provide the required level of protection unless the equipment, protective systems and components are operated in line with their intended use and are installed and maintained according to the relevant codes of practice or requirements. This document is applicable to any equipment, protective systems and components intended to be used in potentially explosive atmospheres. These atmospheres can arise from flammable materials processed, used or released by the equipment, protective systems and components or from materials in the vicinity of the equipment, protective systems and components and/or from the materials of construction of the equipment, protective systems and components. As shot firing can release potentially explosive atmospheres, this document is also applicable to the equipment used for shot firing, apart from the explosives and detonators. This document is applicable to equipment, protective systems and components at all stages of use. This document is not applicable to: — medical devices intended for use in a medical environment; — equipment, protective systems and components where the explosion hazard results exclusively from the presence of explosives or unstable chemical substances; — equipment, protective systems and components where the explosion can result from reaction of substances with oxidising agents other than atmospheric oxygen or by other hazardous reactions or conditions other than atmospheric conditions; — equipment intended for use in domestic and non-commercial environments where explosive atmospheres may only rarely be created and solely as a result of the accidental leakage of fuel gas; — personal protective equipment covered by Regulation (EU) 2016/425; the design and construction of systems containing desired, controlled combustion processes, unless they can act as ignition sources in potentially explosive atmospheres; — mines where firedamp and/or combustible dust are not naturally present and surface installations such as coal preparation plants, power plants, coke oven plants etc. in which an explosive atmosphere can be present, but which are not part of a coal mine. These are covered by EN 1127-1:2019.

prEN ISO 15883-4 Public enquiry
Comment end date 2026-11-26
Washer-disinfectors - Part 4: Requirements and tests for washer-disinfectors employing chemical disinfection for thermolabile endoscopes (ISO/DIS 15883-4:2026)

This document specifies the particular requirements, including performance criteria for washer-disinfectors (WD) that are intended to be used for cleaning and chemical disinfection of thermolabile endoscopes. This document also specifies the performance requirements for the cleaning and disinfection of the washer-disinfector and its components and accessories which can be required to achieve the necessary performance criteria. The methods, instrumentation and instructions required for type testing, works testing, validation (installation, operational and performance qualification on first installation), routine control and monitoring, and requalification of WD periodically and after essential repairs, are also specified. NOTE 1 In addition, Annex A gives guidance on an appropriate division of responsibility for the range of activities covered by this document. NOTE 2 WD complying with this document can also be used for cleaning and chemical disinfection of other thermolabile re-usable medical devices for which the device manufacturer has recommended and validated this method of disinfection. WD complying with the requirements of this document are not intended for cleaning and disinfection of medical devices, including endoscopic accessories, which are heat stable and can be disinfected or sterilized by thermal methods (see ISO 15883-1:2006+Amd 1:2014, 4.1.5). The specified performance requirements of this document do not ensure the inactivation or removal of the causative agent(s) (prion protein) of transmissible spongiform encephalopathies. NOTE 3 If it is considered that prion protein might be present, particular care is needed in the choice of cleaning agents and disinfectants to ensure that the chemicals used do not react with the prion protein and/or other protein in a manner that can inhibit its removal or inactivation from the load or washer-disinfector. NOTE 4 This document can be used by prospective purchasers and manufacturers as the basis of agreement on the specification of the WD, manufacturers of endoscopes, cleaning products, and disinfecting products.

prEN ISO 5667-3 Public enquiry
Comment end date 2026-11-24
Water quality - Sampling - Part 3: Preservation and handling of water samples (ISO/DIS 5667-3:2026)

This document specifies the general requirements for sampling, preservation, handling, transport and storage of all water samples for physicochemical, chemical, hydrobiological and microbiological analyses and determination of radiochemical analytes and activities. Guidance on the validation of storage times of water samples is provided in ISO/TS 5667-25 [2]. This document is not applicable to water samples intended for ecotoxicological assays, biological assays (which is specified in ISO 5667-16 [4]), passive sampling (which is specified in ISO 5667-23 [5]) and microplastics (which is specified in ISO 5667-27 [6]). This document is particularly appropriate when samples cannot be analysed on site and have to be transported to a laboratory for analysis.

Total records found: 159
1 2 3 … 7 arrow-next

Quick filters

Technical Committee
TK 1 Electronics (34) TK 4 Information technology (3) TK 5 Electrical engineering (40) TK 9 Furniture (1) TK 12 Motor - roads (1) TK 18 Telecommunications (18) TK 20 Toys, child use articles, sports and other recreational equipment (1) TK 21 Textiles and personal protective equipment (1) TK 22 Fire safety (5) TK 24 Quality management and quality assurance (1) TK 25 Matrix, gypsum and gypsum based products (10) TK 26 Thermal insulation materials (1) TK 28 Gas systems (1) TK 29 Water supply (10) TK 31 Acoustics (1) TK 32 Health (12) TK 35 Safety of machinery (2) TK 36 Environmental protection (5) TK 38 Building constructions (15) TK 39 Protection (2) TK 40 Petroleuml, petroleum products, lubricants and alternative fuels (2) TK 41 Welding (8) TK 45 Electric power (4) TK 46 Roofs and building waterproof isolation (6) TK 49 Metallic materials (9) TK 50 Heating and Ventilation Systems (3) TK 51 Food analysis- Horizontal methods (2) TK 52 Ophthalmic optics and lasers (1) TK 56 Metal liquid tanks and industrial pipelines (1) TK 57 Fertilizers (2) TK 59 Geotechnics (3) TK 60 Windows and doors (4) TK 68 Plastics (4) TK 70 Pulp, paper, board, adhesives (3) TK 76 Explosive atmospheres (6) TK 79 IT security techniques (3) TK 80 Road transport and traffic telematics (1) TK 81 Conservation of cultural property (1) TK 82 Safety of trackless overground vehicles (1) TK 83 Assessment of workplace exposure to chemical and biological agents (1) TK 87 Biotechnology (8) TK 88 Building Information Modelling (BIM) (1) TK 89 Risk management and organizational governance (1) TK 91 Asset management and technical maintenance (1) TK 94 Circural economy (1) TK 99 Health Informatics (1)
ICS
Hidrologinės dirvožemio savybės (1) Acid secondary cells and batteries (3) Adhesives (3) Aerospace electric equipment and systems (5) Alarm and warning systems (1) Alcohols. Ethers (1) Aluminium and aluminium alloys (1) Aluminium products (1) Ambient atmospheres (1) Amplifiers (3) Anaesthetic, respiratory and reanimation equipment (6) Application of information technology in general (1) Binders. Sealing materials (1) Biology. Botany. Zoology (8) Boilers and heat exchangers (1) Brazing and soldering (1) Building accessories (1) Cellular materials (1) Cement. Gypsum. Lime. Mortar (10) Chemical analysis (1) Chemical laboratories. Laboratory equipment (4) Chemicals for purification of water (3) Cleaning appliances (6) Cleanrooms and associated controlled environments (1) Coaxial cables. Waveguides (1) Colour coding (1) Cooking ranges, working tables, ovens and similar appliances (1) Cranes (1) Diagnostic equipment (1) Disinfectants and antiseptics (1) Domestic safety (6) Earthworks. Excavations. Foundation construction. Underground works (3) Ecolabelling (1) Electric road vehicles (3) Electrical and electronic equipment (2) Electrical and electronic testing (1) Electrical apparatus for explosive atmospheres (4) Electrical engineering in general (1) Electrical equipment of ships and of marine structure (1) Emission (1) Environmental economics. Sustainability (1) Equipment for children (1) Exploratory, drilling and extraction equipment (1) Fertilizers (1) Fibre optic interconnecting devices (1) Fibres and cables (1) Fire protection (1) Fire-fighting (4) Fire-resistance of building materials and elements (1) Flat steel products and semi-products (2) Floor coverings (1) Food microbiology (1) Furniture (1) Fuses and other overcurrent protection devices (2) Generators (1) Geometrical Product Specification (GPS) (1) Governance and ethics (1) Hand and arm protection (1) Hand-operated tools (1) Health care technology (Vocabularies) (1) Home economics in general (2) Immunity (1) Implants for surgery, prosthetics and orthotics (1) Information technology (IT) in general (1) Integrated circuits. Microelectronics (2) Iron and steel pipes (1) IT applications in information, documentation and publishing (1) IT applications in science (1) IT applications in transport (1) IT Security (3) Items of art and handicrafts. Cultural property and heritage (1) Laminated sheets (1) Laundry appliances (2) Leather and furs (2) Liquid fuels (1) Luminaires (3) Maintenance services. Facilities management (1) Materials and components for railway engineering (1) Mechanical testing of metals (1) Mining equipment in general (1) Miscellaneous domestic and commercial equipment (1) Multilayer applications (1) Networking (2) Non-ferrous metal pipes (2) Oilseeds (1) Ophthalmic equipment (1) Other fluid power system components (1) Other kitchen equipment (1) Other lifting equipment (1) Other semiconductor devices (2) Paints and varnishes (2) Petroleum products and natural gas handling equipment (1) Pipelines and its parts for district heat (1) Plastics in general (1) Plug-and-socket devices. Connectors (1) Primary cells and batteries (2) Printed circuits and boards (3) Product and company certification. Conformity assessment (1) Protection against crime (1) Protection against falling and slipping (1) Pumps (2) Radiation measurements (1) Radiographic equipment (1) Railway rolling stock in general (2) Refrigerating technology (1) Relays (1) RF connectors (2) Rivets (1) Road construction materials (1) Road equipment and installations (1) Roofs (1) Safety of machinery (1) Seismic and vibration protection (1) Small craft (3) Small kitchen appliances (1) Stainless steels (2) Stationary containers and tanks (1) Stationary source emissions (1) Steel structures (3) Sterilization and disinfection in general (1) Sterilizing equipment (1) Surface preparation (4) Switches (1) Technical aspects (7) TELECOMMUNICATIONS. AUDIO AND VIDEO ENGINEERING (18) Thermal and sound insulating materials (6) Timber structures (1) Transformers. Reactors (2) Ventilators. Fans. Air-conditioners (3) Vibration and shock with respect to human beings (1) Walls. Partitions. Façades (3) Washers and other locking elements (1) Water heating equipment (2) Water supply systems (7) Welded joints and welds (5) Welding equipment (2) Wires (11) Wood-protecting chemicals (2) Wood, sawlogs and sawn timber (1) Workplace atmospheres (1)