Standartų projektų sąrašas

prEN ISO/IEEE 11073-10442 Viešoji apklausa

Komentavimo iki data 2026-09-21

Sveikatos informatika. Įtaisų funkcinis suderinamumas. 10442 dalis. Ryšys tarp asmeninių medicinos įtaisų. Įtaiso specializavimas. Jėgos treniravimo įranga (ISO/IEEE FDIS 11073-10442:2026)

Abstract: Within the context of the ISO/IEEE 11073 family of standards for device communication, this standard establishes a normative definition of the communication between personal strength fitness devices and managers (e.g., cell phones, personal computers, personal health appliances, and set top boxes) in a manner that enables plug-and-play interoperability. It leverages appropriate portions of existing standards including ISO/IEEE 11073 terminology and information models. It specifies the use of specific term codes, formats, and behaviors in telehealth environments restricting optionality in base frameworks in favor of interoperability. This standard defines a common core of communication functionality for personal telehealth strength fitness devices. In this context, strength fitness devices are being used broadly to cover strength fitness devices that measure musculo-skeletal strength-conditioning activities. Keywords: medical device communication, personal health devices, strength fitness equipment

Skaityti, komentuoti projektą Peržiūrėti metaduomenis

prEN ISO/IEEE 11073-10419 Viešoji apklausa

Komentavimo iki data 2026-09-21

Sveikatos informatika. Ryšys tarp asmeninių medicinos įtaisų. 10419 dalis. Įtaiso specializavimas. Insulino pompa (ISO/IEEE FDIS 11073-10419:2026)

This standard establishes a normative definition of communication between personal telehealth insulin pump devices (agents) and managers (e.g., cell phones, personal computers, personal health appliances, set top boxes) in a manner that enables plug-and-play interoperability. It leverages work done in other ISO/IEEE 11073 standards including existing terminology, information profiles, application profile standards, and transport standards. It specifies the use of specific term codes, formats, and behaviors in telehealth environments, restricting optionality in base frameworks in favor of interoperability. This standard defines a common core functionality of personal telehealth insulin pump devices. In the context of personal health devices (PHDs), an insulin pump is a medical device used for the administration of insulin in the treatment of diabetes mellitus, also known as continuous subcutaneous insulin infusion (CSII) therapy. This standard provides the data modeling according to ISO/IEEE 11073-20601 and does not specify the measurement method.

Skaityti, komentuoti projektą Peržiūrėti metaduomenis

prEN ISO 17516 Viešoji apklausa

Komentavimo iki data 2026-09-19

Kosmetikos gaminiai. Mikrobiologija. Mikrobiologinės ribinės vertės (ISO/DIS 17516:2026)

ISO 17516:2014 is applicable for all cosmetics and assists interested parties in the assessment of the microbiological quality of the products. Microbiological testing does not need to be performed on those products considered to be microbiologically low risk.

Skaityti, komentuoti projektą Peržiūrėti metaduomenis

prEN ISO 19161-2 Viešoji apklausa

Komentavimo iki data 2026-09-19

Geografinė informacija. Geodezinės koordinatės. 2 dalis. Geodezinių antžeminių stočių unikalusis identifikavimas (ISO/DIS 19161-2:2026)

This standard will provide a description of the numbering system replacing the DOMES numbering. The description of the DOMES numbering can be found in MERIT/COTES joint working groups, MERIT campaign: connection of reference frames, implementation plan, 1983. The standard will provide to the geodetic data producers and users a proper identification of the permanently instrumented stations, (e.g. those used in the production of the International Terrestrial Reference Frame and other similar stations), with special emphasis on the backward compatibility with existing DOMES numbers, which will have a positive impact on interoperability issues when merging several data from different communities. This standard will: • support interoperability among GNSS providers (GPS, GLONASS, GALILEO, BEIDOU, …) • clarify the potential confusion between communities which have already adopted their own numbering systems • support the UNGGIM GGRF resolution on global geodetic infrastructure.

Skaityti, komentuoti projektą Peržiūrėti metaduomenis

prEN IEC 80000-6:2026 Viešoji apklausa

Komentavimo iki data 2026-09-18

Dydžiai ir vienetai. 6 dalis. Elektromagnetizmas

Skaityti, komentuoti projektą Peržiūrėti metaduomenis

prEN 1459-1 Viešoji apklausa

Komentavimo iki data 2026-09-17

Visureigiai krautuvai. Saugos reikalavimai ir patikrinimas. 1 dalis. Kintamojo siekio krautuvai

This document specifies the safety requirements of self-propelled rough-terrain variable-reach trucks (hereafter referred to as trucks), intended to handle loads, equipped with a telescopic lifting means (pivoted boom), on which a load handling device (e.g. carriage and fork arms) is fitted. For the purpose of this document, rough-terrain variable-reach trucks are designed to transport, lift and place loads and can be driven on unimproved terrain. Fork arms are considered to be part of the truck. Trucks can also be equipped with a variety of attachments (e.g. bale spikes, mowers, sweepers). This document deals with all the significant hazards, hazardous situations and events relevant to the trucks when they are used as intended and under conditions of misuse which are reasonably foreseeable by the manufacturer (see Annex A). This document does not apply to: — slewing rough-terrain variable-reach trucks covered by EN 1459 2:2015+A1:2018; — rough-terrain variable-reach tractors covered by prEN 17968:2025; — industrial variable reach trucks covered by EN ISO 3691 2:2023; — lorry-mounted variable-reach trucks covered by ISO 20297 1:2017; — variable-reach trucks fitted with tilting or elevating operator position; — mobile cranes covered by EN 13000:2010+A1:2014; — machines designed primarily for earth moving, even if their buckets and blades are replaced with forks (see EN 474 series); — trucks designed primarily with variable length load suspension elements (e.g. chain, ropes) from which the load may swing freely in all directions; — trucks designed primarily for container handling; — trucks on tracks; — trucks with articulated chassis; — attachments. This document does not cover sales literature. This document does not address hazards linked to: — operation of the truck from a position other than the normal operating position; — operation of the truck by a remote control; — gas power systems; — gasoline engine systems; — autonomous functions; — self-evolving behaviour; — hybrid or battery power systems having a voltage greater than 32 V DC or 21 V AC r.m.s. NOTE EN 1459-7:2026 deals with hybrid and battery power systems having a voltage greater than 32 V DC or 21 V AC r.m.s. This document does not address hazards which may occur: a) when handling suspended loads which may swing freely (additional requirements are given in EN 1459 4:2020+A1:2025); b) when using trucks on public roads; c) when operating in potentially explosive atmospheres (additional requirements are given in EN 1755:2024); d) when operating underground; e) when fitted with a personnel work platform (additional requirements are given in EN 1459 3:2015 and EN 1459 9:2021); f) when using system capable of controlling the speed of the truck as set by the operator (cruise-control). This document is not applicable to trucks manufactured before the date of its publication.

Skaityti, komentuoti projektą Peržiūrėti metaduomenis

prEN 12999 Viešoji apklausa

Komentavimo iki data 2026-09-17

Kranai. Krovimo kranai

This document specifies requirements for design, calculation, examinations and tests of hydraulic powered loader cranes and their mountings on vehicles or static foundations. This document applies to loader cranes designed to be installed on: - road vehicles, including trailers, with load carrying capability; - tractors (road or agricultural), where only a towed trailer has capability to carry goods; - demountable bodies to be carried by any of the above; - other types of carriers (e.g. separate loaders, crawlers, rail vehicles, non-seagoing vessels); - static foundations. NOTE 1 A demountable body is a detachable frame designed to be carried by a vehicle or trailer. NOTE 2 A separate loader is a vehicle, with no load carrying capacity, equipped with a loader crane and designed to load or unload other vehicles and trailers. This document also applies to loader cranes equipped with special tools or interchangeable equipment (e.g. grapple, clamshell bucket, pallet clamp, etc.), as specified in the operator’s manual. This document does not apply to loader cranes used on board sea going vessels or to articulated boom system cranes which are designed as total integral parts of special equipment such as forwarders. The hazards covered by this document are identified in Clause 4. This document does not cover hazards related to the lifting of persons. NOTE 3 The use of cranes for lifting of persons can be subject to specific national regulations. This document is not applicable to loader cranes manufactured before the publication of this document. For loader cranes designed before the publication of this document, the provisions concerning stress calculations in the version of EN 12999 that was valid at the time of their design, are still applicable.

Skaityti, komentuoti projektą Peržiūrėti metaduomenis

prEN ISO 19321 Viešoji apklausa

Komentavimo iki data 2026-09-17

Intelektinės transporto sistemos. Sąveikiosios ITS. Transporto priemonės informacijos duomenų struktūrų žodynas (ISO/DIS 19321:2026)

This document specifies the in-vehicle information (IVI) data structures that are required by different intelligent transport system (ITS) services for exchanging information between ITS stations (ITS-S). A general, extensible data structure is specified, which is split into structures called containers to accommodate current-day information. Transmitted information includes IVI such as contextual speed, road works warnings, vehicle restrictions, lane restrictions, road hazard warnings, location-based services and re-routing. The information in the containers is organized in sub-structures called data frames and data elements, which are described in terms of their content and syntax. The data structures are specified as communications-agnostic. This document does not provide the communication protocols. This document provides scenarios for usage of the data structure, e.g. in case of real time, short-range communications.

Skaityti, komentuoti projektą Peržiūrėti metaduomenis

prEN 545 Viešoji apklausa

Komentavimo iki data 2026-09-17

Stipriojo ketaus vandentiekio vamzdžiai, jungiamosios detalės, pagalbiniai reikmenys ir jų jungtys. Reikalavimai ir bandymo metodai

This document specifies the requirements and associated test methods applicable to ductile iron pipes, fittings, accessories and their joints for the construction of pipelines outside buildings: — to convey different types of water (e.g. raw water, treated water, re-used water) for all types of applications (e.g. water intended for human consumption, for fire protection, for snow making, for irrigation, for hydro-electricity etc.); — with or without pressure; — to be installed below or above ground. This document is applicable to pipes, fittings and accessories which are: — manufactured with socketed, flanged or spigot ends; — supplied externally and internally coated; — suitable for fluid temperatures between 0 °C and 50 °C, excluding frost; — not intended for use in areas subject to reaction to fire regulations. This does not preclude special arrangements for the products to be used at higher temperatures. This document covers pipes and fittings cast by any type of foundry process or manufactured by fabrication of cast components, as well as corresponding joints and accessories, in a size range extending from DN 40 to DN 2 000, inclusive. This document specifies requirements for materials, dimensions and tolerances, mechanical properties and standard coatings of ductile iron pipes and fittings. It also gives performance requirements for all components including joints. Joint design and gasket shapes are outside the scope of this document. In addition, reference is made to the minimum performance requirements of couplings, flange adaptors and saddles manufactured for use with ductile iron pipes and fittings. NOTE In this document, all pressures are relative pressures, expressed in bars (100 kPa = 1 bar).

Skaityti, komentuoti projektą Peržiūrėti metaduomenis

prEN 481 Viešoji apklausa

Komentavimo iki data 2026-09-17

Darbo vietos oras. Frakcijų granuliometrinės sudėties apbrėžimai ore esančioms dalelėms matuoti

This document specifies sampling conventions for airborne particle size fractions to assess health-related exposure resulting from the inhalation of particles in workplace atmospheres. Conventions are defined for the inhalable, thoracic and respirable fractions. The sampling conventions only describe the inhalation of particles and their penetration in the respiratory tract as governed by inertia (impaction). Exhaled particles and deposition in the respiratory tract by other mechanisms, e.g. diffusion, are not considered in this document. The sampling conventions defined in this document apply to both indoor and outdoor workplaces. The conventions assume particles penetration and only oral breathing as a worst-case scenario. Nevertheless, the conventions are applicable to both oral and nasal breathing. The conventions are defined based on assumptions given in Clause 6. The choice of convention for a specific application depends on the region of the respiratory tract affected by the health impact of the particle component of interest (see Clause 5). The conventions can be applied to various metrics, including particle number, length, surface area, volume, or mass, depending on the type of particle analysis performed on the sampled aerosol fraction. The health-related fraction concentrations defined in this document are often expressed as the mass of sampled particles per volume of sampled air to allow comparison with mass-based occupational exposure limit values. The conventions primarily apply to the aforementioned metrics, however, they are not applicable to situations involving limit values expressed in a different metric, such as fibre limit values defined by length, diameter, and aspect ratio, unless a measurement procedure explicitly specifies sampling a particular health-related size fraction [11]. The primary objective of this document is to establish standardized conventions for health-related particle size fractions. Sampling is generally carried out using dedicated samplers, for which there is no need to measure the aerodynamic size distribution of the airborne particles to be sampled. Samplers separating airborne particles into one or more relevant fractions are currently available. In general, no assumptions or pre-knowledge are needed on the number of modes, modal diameter(s) or width of the particle aerodynamic size distribution of the airborne particles to be sampled. The conventions in this document are intended to be used for the determination of the exposure of an average worker based on average penetration curves. This document is not intended to determine the deposited dose of an individual worker. The conventions are primarily intended for assessing workers’ exposure to airborne particles by sampling the airborne particles. This document does not apply to large particles emitted at high speed that travel due to their initial momentum, instead of being carried by the air (airborne) and aspirated into humans’ respiratory tract and aerosol samplers by suction (see Annex B). All wind speeds referenced throughout this document are based on the relative speed between the worker and the surrounding air.

Skaityti, komentuoti projektą Peržiūrėti metaduomenis

prEN IEC 63270-2:2026 Viešoji apklausa