Standartų projektų sąrašas

Paieškos frazė

Išplėstinė paieška

Žymuo

Direktyvos

Organizacija

ICS

Technikos komitetas

Užsienio komitetas

Darbo grupė

Etapas

Būsena

Komentavimo data

iki

Rezultatai

prEN 10219-1 Viešoji apklausa

Komentavimo iki data 2026-05-28

Nelegiruotojo ir smulkiagrūdžio plieno šaltai formuoti suvirintieji tuščiaviduriai statybiniai profiliuočiai. 1 dalis. Techninės tiekimo sąlygos

This document specifies the technical delivery conditions for electric welded and submerged arc welded cold formed structural steel hollow sections of circular, square, rectangular or elliptical forms and applies to structural hollow sections formed cold without subsequent heat treatment other than the heat treatment of the weld line. NOTE 1 The requirements for tolerances, dimensions and sectional properties in EN 10219-2. NOTE 2 The provisions that apply under the Construction Products Regulations (CPR) are specified in EN 10380. NOTE 3 The attention of users is drawn to the fact that whilst cold formed grades in this document can have equivalent mechanical properties to hot-finished grades in EN 10210-1 the sectional properties of square and rectangular hollow sections in EN 10219-2 and EN 10210-2 are not equivalent. NOTE 4 A range of steel grades is specified in this document and the user should select the grade most appropriate to the intended use and service conditions. The grades and mechanical properties, but not the final supply condition of cold formed hollow sections are generally comparable with those in EN 10025-2, EN 10025-3, EN 10025-4, EN 10025-5, EN 10025-6, EN 10149-2 and EN 10149-3.

Skaityti, komentuoti projektą Peržiūrėti metaduomenis

prEN 10210-1 Viešoji apklausa

Komentavimo iki data 2026-05-28

Karštuoju būdu apdoroti nelegiruotojo ir smulkiagrūdžio plieno tuščiaviduriai statybiniai profiliuočiai. 1 dalis. Techninės tiekimo sąlygos

This document specifies technical delivery conditions for hot-finished seamless, electric welded and submerged arc welded steel structural hollow sections of circular, square, rectangular or elliptical forms. It applies to hollow sections formed hot, with or without subsequent heat treatment, or formed cold with subsequent heat treatment above 580 °C to obtain equivalent mechanical properties to those obtained in the hot formed product. NOTE 1 The requirements for tolerances, dimensions and sectional properties are specified in EN 10210-2. NOTE 2 The provisions that apply under the Construction Products Regulations (CPR) are specified in EN 10380. NOTE 3 The attention of users is drawn to the fact that whilst cold formed grades in EN 10219-1 can have equivalent mechanical properties to hot-finished grades in this document the sectional properties of square and rectangular hollow sections in EN 10210-2 and EN 10219-2 are not equivalent. NOTE 4 A range of material grades is specified in this standard and the user should select the grade most appropriate to the intended use and service conditions. The grades and mechanical properties of the finished hollow sections are generally comparable with those in EN 10025-2, EN 10025-3, EN 10025-4, EN 10025-5 and EN 10025-6. NOTE 5 The requirements for seamless and welded steel structural hollow sections for use in offshore structures are covered in EN 10225. NOTE 6 Spiral welded hollow sections must be used with caution in applications involving dynamic behaviour (fatigue stress) as, up to now, there is insufficient data regarding their performance.

Skaityti, komentuoti projektą Peržiūrėti metaduomenis

Būtini slapukai

Statistikos slapukai

El. pašto prenumerata

Išplėstinė paieška

Rezultatai

Greitieji filtrai

Organizacija

Technikos komitetas

ICS