Standartų projektų sąrašas

prEN IEC 60793-1-51:2026 Viešoji apklausa

Komentavimo iki data 2026-04-10

Optinės skaidulos. 1-51 dalis. Matavimo metodai ir bandymo procedūros. Sausosios šilumos (nuostovioji būsena) bandymai

Skaityti, komentuoti projektą Peržiūrėti metaduomenis

prEN IEC 60793-1-52:2026 Viešoji apklausa

Komentavimo iki data 2026-04-10

Optinės skaidulos. 1-52 dalis. Matavimo metodai ir bandymo procedūros. Temperatūros kitimo bandymai

Skaityti, komentuoti projektą Peržiūrėti metaduomenis

prEN IEC 61225:2026 Viešoji apklausa

Komentavimo iki data 2026-04-10

Branduolinės elektrinės. Matavimo aparatūros, valdymo ir elektros tiekimo sistemos. Reikalavimai, keliami statinėms nenutrūkstamo nuolatinės ir kintamosios srovės tiekimo sistemoms

See the scope of IEC 61225:2025. Adoption is to be implemented without modification.

Skaityti, komentuoti projektą Peržiūrėti metaduomenis

EN 50440:2015/prA2:2026 Viešoji apklausa

Komentavimo iki data 2026-04-10

Buitinių elektrinių kaupiamųjų vandens šildytuvų našumas ir bandymo metodai

This European Standard specifies methods for measuring the performance of electric storage water heaters for the production of sanitary hot water for household and similar use. The object is to state and define the principal performance characteristics of electric storage water heaters and to describe the test methods for measuring these characteristics. NOTE 1 This standard does not apply to; − storage water heaters that use electricity as a secondary source of heating the water; − storage water heaters that do not use a tank to store hot water; − electric storage water heaters that do not meet the minimum (or maximum) output performance of the smallest (or biggest) load profile, as defined in Table 4. NOTE 2 This standard does not specify performance or safety requirements. For safety requirements see EN 60335-1:2020 in conjunction with EN 60335-2-21:2023

Skaityti, komentuoti projektą Peržiūrėti metaduomenis

prEN 50583-1:2026 Viešoji apklausa

Komentavimo iki data 2026-04-10

Fotovoltinė įranga pastatuose. 1 dalis. Į pastatus integruojami fotovoltiniai moduliai

This document applies to photovoltaic modules that contain at least one glass pane and which are used as construction products. It focuses on the properties of these photovoltaic modules relevant to essential building requirements as specified in the European Construction Product Regulation CPR 305/2011, and the applicable electro-technical requirements as stated in the Low Voltage Directive 2014/35/EU / or CENELEC standards. The CE mark of building integrated photovoltaic (BIPV) modules will thus state properties based on both documents as they are both equally applicable. This document references international standards, technical reports and guidelines. For some mounting categories, in addition, national standards (or regulations) for building products may apply in individual countries, which are not explicitly referenced here and for which harmonized European Standards are not yet available. The document is addressed to manufacturers, planners, system designers, installers, testing institutes and building authorities. This document does not address concentrating or building-attached photovoltaic modules (BAPV). This document addresses requirements on the PV modules in the specific ways they are intended to be mounted. Separable mounting structures are within the scope of EN 50583 2. NOTE For the definition of building-attached photovoltaic modules (BAPV) refer to Clause 3.

Skaityti, komentuoti projektą Peržiūrėti metaduomenis

prEN IEC 61009-2-1:2026/prAA:2026 Viešoji apklausa

Komentavimo iki data 2026-04-08

Buitiniai ir panašios paskirties liekamąja srove valdomi jungtuvai su integruota apsauga nuo viršsrovių. 2-1 dalis. Liekamąja srove valdomi jungtuvai su integruota apsauga nuo viršsrovių pagal 4.1.1 klasifikaciją

IEC 61009-1:2024, Clause 1 is applicable except for the first paragraph and the last paragraph, which are replaced by the following, respectively: This document applies to residual current operated circuit-breakers with integral overcurrent protection for household and similar uses (hereafter referred to as RCBOs), classified according to IEC 61009-1:2024, 4.1.1. RCBOs according to this document are intended for voltages not exceeding 440 V AC with frequencies of 50 Hz, 60 Hz or 50/60 Hz and currents not exceeding 125 A and rated short-circuit capacities not exceeding 25 000 A for operation at 50 Hz or 60 Hz. This document applies in conjunction with IEC 61009-1:2024. It specifies requirements, tests and test sequences to verify compliance and is used for certification purposes.

Skaityti, komentuoti projektą Peržiūrėti metaduomenis

prEN IEC 61008-2-1:2026/prAA:2026 Viešoji apklausa

Komentavimo iki data 2026-04-08

Buitiniai ir panašios paskirties liekamąja srove valdomi jungtuvai be integruotos apsaugos nuo viršsrovių. 2-1 dalis. Liekamąja srove valdomi jungtuvai be integruotos apsaugos nuo viršsrovių pagal 4.1.1 klasifikaciją

IEC 61008-1:2024, Clause 1 is applicable except for the first paragraph, which is replaced by the first paragraph below, and the last paragraph, which is replaced by the second paragraph below: This part of IEC 61008 applies to residual current operated circuit-breakers, without integral overcurrent protection, for household and similar uses (hereafter referred to as RCCBs), classified according to IEC 61008-1:2024, 4.1.1. RCCBs according to this document are intended for voltages not exceeding 440 V AC with frequencies of 50 Hz, 60 Hz or 50/60 Hz and currents not exceeding 125 A, intended principally for protection against shock hazard. This document applies in conjunction with IEC 61008-1:2024. It specifies requirements, tests and test sequences to verify compliance and is used for certification purposes.

Skaityti, komentuoti projektą Peržiūrėti metaduomenis

prEN IEC 61009-2-1:2026 Viešoji apklausa

Komentavimo iki data 2026-04-08

Buitiniai ir panašios paskirties liekamąja srove valdomi jungtuvai su integruota apsauga nuo viršsrovių. 2-1 dalis. Liekamąja srove valdomi jungtuvai su integruota apsauga nuo viršsrovių pagal 4.1.1 klasifikaciją

IEC 61009-1:2024, Clause 1 is applicable except for the first paragraph and the last paragraph, which are replaced by the following, respectively: This document applies to residual current operated circuit-breakers with integral overcurrent protection for household and similar uses (hereafter referred to as RCBOs), classified according to IEC 61009-1:2024, 4.1.1. RCBOs according to this document are intended for voltages not exceeding 440 V AC with frequencies of 50 Hz, 60 Hz or 50/60 Hz and currents not exceeding 125 A and rated short-circuit capacities not exceeding 25 000 A for operation at 50 Hz or 60 Hz. This document applies in conjunction with IEC 61009-1:2024. It specifies requirements, tests and test sequences to verify compliance and is used for certification purposes.

Skaityti, komentuoti projektą Peržiūrėti metaduomenis

prEN IEC 61008-2-1:2026 Viešoji apklausa

Komentavimo iki data 2026-04-08

Buitiniai ir panašios paskirties liekamąja srove valdomi jungtuvai be integruotos apsaugos nuo viršsrovių. 2-1 dalis. Liekamąja srove valdomi jungtuvai be integruotos apsaugos nuo viršsrovių pagal 4.1.1 klasifikaciją

IEC 61008-1:2024, Clause 1 is applicable except for the first paragraph, which is replaced by the first paragraph below, and the last paragraph, which is replaced by the second paragraph below: This part of IEC 61008 applies to residual current operated circuit-breakers, without integral overcurrent protection, for household and similar uses (hereafter referred to as RCCBs), classified according to IEC 61008-1:2024, 4.1.1. RCCBs according to this document are intended for voltages not exceeding 440 V AC with frequencies of 50 Hz, 60 Hz or 50/60 Hz and currents not exceeding 125 A, intended principally for protection against shock hazard. This document applies in conjunction with IEC 61008-1:2024. It specifies requirements, tests and test sequences to verify compliance and is used for certification purposes.

Skaityti, komentuoti projektą Peržiūrėti metaduomenis

prEN IEC 61009-1:2026/prAA:2026 Viešoji apklausa

Komentavimo iki data 2026-04-08

Buitiniai ir panašios paskirties liekamąja srove valdomi jungtuvai su integruota apsauga nuo viršsrovių. 1 dalis. Bendrosios taisyklės

This document gives general requirements and tests for residual current operated circuit-breakers with integral overcurrent protection for household and similar uses (hereafter referred to as RCBOs), for rated operational voltages not exceeding 440 V AC, with rated frequencies of 50 Hz, 60 Hz or 50/60 Hz and rated currents not exceeding 125 A and rated short-circuit capacities not exceeding 25 000 A. RCBOs are intended to provide fault protection (previously referred to as protection against indirect contact), the exposed conductive parts of the installation being connected to an appropriate earth electrode. These devices are also intended to protect against overcurrents in the wiring installations of buildings and similar applications. They are also intended to be used to provide protection against fire hazards due to a persistent earth fault current. RCBOs having a rated residual operating current not exceeding 30 mA are used for fault protection and additional protection in the case of failure of the protective provisions against electric shock. This document applies to RCBOs performing simultaneously the functions of detection of the residual current, of comparison of the value of this current with the residual operating value and of opening of the protected circuit when the residual current exceeds this value. These devices also perform the function of making, carrying and breaking overcurrents under specified conditions. RCBOs are intended to be operated by ordinary or uninstructed persons and designed not to require maintenance. The requirements of this document apply for standard conditions (see 7.1). Additional requirements can be necessary for RCBOs used in locations which have severe environmental conditions. RCBOs within the scope of this document are intended for use in an environment with pollution degree 2 (see 7.3). RCBOs are suitable for isolation. Special precautions (e.g. surge protective devices) can be necessary when excessive overvoltages are likely to occur on the supply side (for example in the case of supply through overhead lines, see IEC 60364-4-44 and IEC 60364-5-53). RCBOs, with the exception of those with an uninterrupted neutral, are suitable for use in IT systems. RCBOs of the general type are resistant to current surges, including the case where surge voltages (as a result of switching transients or induced by lightning) cause loading currents in the installation without occurrence of flashover. RCBOs of type S are considered to be sufficiently resistant against unwanted tripping even if the surge voltage causes a flashover and a follow-on current occurs. This document also applies to RCBOs obtained by the assembly of an adaptable residual current device with a circuit-breaker. The mechanical assembly is intended to be effected in the factory by the manufacturer, or on site, in which case the requirements of Annex G apply. It also applies to RCBOs having more than one rated current, provided that the means for changing from one discrete rating to another is not accessible in normal service and that the rating cannot be changed without the use of a tool. Particular requirements are necessary for RCBOs intended to be used at frequencies other than 50 Hz or 60 Hz. For RCBOs incorporated in, or intended for association with socket-outlets only, the requirements of this document can be used, as far as applicable, in conjunction with the requirements of IEC 60884-1 or the national requirements of the country where the product is placed on the market. This document does not apply to: ....

Skaityti, komentuoti projektą Peržiūrėti metaduomenis

prEN IEC 61008-1:2026/prAA:2026 Viešoji apklausa

Komentavimo iki data 2026-04-08

Buitiniai ir panašios paskirties liekamąja srove valdomi jungtuvai be integruotos apsaugos nuo viršsrovių. 1 dalis. Bendrosios taisyklės

This document gives general requirements and tests for residual current operated circuit-breakers without integral overcurrent protection for household and similar uses (hereafter referred to as RCCBs), for rated operational voltages not exceeding 440 V AC, with rated frequencies of 50 Hz, 60 Hz or 50/60 Hz and rated currents not exceeding 125 A, intended principally for protection against shock hazard. RCCBs are intended to provide fault protection (previously referred to as protection against indirect contact), the exposed conductive parts of the installation being connected to an appropriate earth electrode. They are also intended to be used to provide protection against fire hazards due to a persistent earth fault current. RCCBs having a rated residual operating current not exceeding 30 mA are used for fault protection and additional protection in the case of failure of the protective provisions against electric shock. This document applies to RCCBs performing simultaneously the functions of detection of the residual current, of comparison of the value of this current with the residual operating value and of opening of the protected circuit when the residual current exceeds this value. RCCBs are intended to be operated by ordinary or uninstructed persons and designed not to require maintenance. The requirements of this document apply for standard conditions (see 7.1). Additional requirements can be necessary for RCCBs used in locations which have severe environmental conditions. RCCBs within the scope of this document are intended for use in an environment with pollution degree 2 (see 7.3) and overvoltage category III. RCCBs are suitable for isolation. Special precautions (e.g. surge protective devices) can be necessary when excessive overvoltages are likely to occur on the supply side (for example in the case of supply through overhead lines, see IEC 60364-4-44 and IEC 60364-5-53). RCCBs are suitable for use in IT systems. RCCBs of the general type are resistant to current surges, including the case where surge voltages (as a result of switching transients or induced by lightning) cause loading currents in the installation without occurrence of flashover. RCCBs of type S are considered to be sufficiently resistant against unwanted tripping even if the surge voltage causes a flashover and a follow-on current occurs. Particular requirements are necessary for RCCBs intended to be used at frequencies other than 50 Hz or 60 Hz. For RCCBs incorporated in, or intended for association with socket-outlets only, the requirements of this document can be used, as far as applicable, in conjunction with the requirements of IEC 60884-1 or the national requirements of the country where the product is placed on the market. This document does not apply to: – RCCBs the current setting of which is adjustable without a tool; – RCCBs including batteries. This document is not intended to be used alone; it is intended to be used in conjunction with the relevant product standard, IEC 61008-2-1 or IEC 61008-2-2.

Skaityti, komentuoti projektą Peržiūrėti metaduomenis

prEN IEC 61009-1:2026 Viešoji apklausa

Komentavimo iki data 2026-04-08

Buitiniai ir panašios paskirties liekamąja srove valdomi jungtuvai su integruota apsauga nuo viršsrovių. 1 dalis. Bendrosios taisyklės

This document gives general requirements and tests for residual current operated circuit-breakers with integral overcurrent protection for household and similar uses (hereafter referred to as RCBOs), for rated operational voltages not exceeding 440 V AC, with rated frequencies of 50 Hz, 60 Hz or 50/60 Hz and rated currents not exceeding 125 A and rated short-circuit capacities not exceeding 25 000 A. RCBOs are intended to provide fault protection (previously referred to as protection against indirect contact), the exposed conductive parts of the installation being connected to an appropriate earth electrode. These devices are also intended to protect against overcurrents in the wiring installations of buildings and similar applications. They are also intended to be used to provide protection against fire hazards due to a persistent earth fault current. RCBOs having a rated residual operating current not exceeding 30 mA are used for fault protection and additional protection in the case of failure of the protective provisions against electric shock. This document applies to RCBOs performing simultaneously the functions of detection of the residual current, of comparison of the value of this current with the residual operating value and of opening of the protected circuit when the residual current exceeds this value. These devices also perform the function of making, carrying and breaking overcurrents under specified conditions. RCBOs are intended to be operated by ordinary or uninstructed persons and designed not to require maintenance. The requirements of this document apply for standard conditions (see 7.1). Additional requirements can be necessary for RCBOs used in locations which have severe environmental conditions. RCBOs within the scope of this document are intended for use in an environment with pollution degree 2 (see 7.3). RCBOs are suitable for isolation. Special precautions (e.g. surge protective devices) can be necessary when excessive overvoltages are likely to occur on the supply side (for example in the case of supply through overhead lines, see IEC 60364-4-44 and IEC 60364-5-53). RCBOs, with the exception of those with an uninterrupted neutral, are suitable for use in IT systems. RCBOs of the general type are resistant to current surges, including the case where surge voltages (as a result of switching transients or induced by lightning) cause loading currents in the installation without occurrence of flashover. RCBOs of type S are considered to be sufficiently resistant against unwanted tripping even if the surge voltage causes a flashover and a follow-on current occurs. This document also applies to RCBOs obtained by the assembly of an adaptable residual current device with a circuit-breaker. The mechanical assembly is intended to be effected in the factory by the manufacturer, or on site, in which case the requirements of Annex G apply. It also applies to RCBOs having more than one rated current, provided that the means for changing from one discrete rating to another is not accessible in normal service and that the rating cannot be changed without the use of a tool. Particular requirements are necessary for RCBOs intended to be used at frequencies other than 50 Hz or 60 Hz. For RCBOs incorporated in, or intended for association with socket-outlets only, the requirements of this document can be used, as far as applicable, in conjunction with the requirements of IEC 60884-1 or the national requirements of the country where the product is placed on the market. This document does not apply to: .........

Skaityti, komentuoti projektą Peržiūrėti metaduomenis

prEN IEC 61008-1:2026 Viešoji apklausa

Komentavimo iki data 2026-04-08

Buitiniai ir panašios paskirties liekamąja srove valdomi jungtuvai be integruotos apsaugos nuo viršsrovių. 1 dalis. Bendrosios taisyklės

This document gives general requirements and tests for residual current operated circuit-breakers without integral overcurrent protection for household and similar uses (hereafter referred to as RCCBs), for rated operational voltages not exceeding 440 V AC, with rated frequencies of 50 Hz, 60 Hz or 50/60 Hz and rated currents not exceeding 125 A, intended principally for protection against shock hazard. RCCBs are intended to provide fault protection (previously referred to as protection against indirect contact), the exposed conductive parts of the installation being connected to an appropriate earth electrode. They are also intended to be used to provide protection against fire hazards due to a persistent earth fault current. RCCBs having a rated residual operating current not exceeding 30 mA are used for fault protection and additional protection in the case of failure of the protective provisions against electric shock. This document applies to RCCBs performing simultaneously the functions of detection of the residual current, of comparison of the value of this current with the residual operating value and of opening of the protected circuit when the residual current exceeds this value. RCCBs are intended to be operated by ordinary or uninstructed persons and designed not to require maintenance. The requirements of this document apply for standard conditions (see 7.1). Additional requirements can be necessary for RCCBs used in locations which have severe environmental conditions. RCCBs within the scope of this document are intended for use in an environment with pollution degree 2 (see 7.3). RCCBs are suitable for isolation. Special precautions (e.g. surge protective devices) can be necessary when excessive overvoltages are likely to occur on the supply side (for example in the case of supply through overhead lines, see IEC 60364-4-44 and IEC 60364-5-53). RCCBs, with the exception of those with an uninterrupted neutral, are suitable for use in IT systems. RCCBs of the general type are resistant to current surges, including the case where surge voltages (as a result of switching transients or induced by lightning) cause loading currents in the installation without occurrence of flashover. RCCBs of type S are considered to be sufficiently resistant against unwanted tripping even if the surge voltage causes a flashover and a follow-on current occurs. Particular requirements are necessary for RCCBs intended to be used at frequencies other than 50 Hz or 60 Hz. For RCCBs incorporated in, or intended for association with socket-outlets only, the requirements of this document can be used, as far as applicable, in conjunction with the requirements of IEC 60884-1 or the national requirements of the country where the product is placed on the market. This document does not apply to: – RCCBs the current setting of which is adjustable without a tool; – RCCBs including batteries. This document is not intended to be used alone; it is intended to be used in conjunction with the relevant product standard, IEC 61008-2-1 or IEC 61008-2-2.

Skaityti, komentuoti projektą Peržiūrėti metaduomenis

prEN IEC 60730-2-10:2026 Viešoji apklausa

Komentavimo iki data 2026-04-08

Buitiniai ir panašios paskirties automatiniai elektriniai valdymo įtaisai. 2-10 dalis. Ypatingieji reikalavimai, keliami variklių paleidimo relėms

Skaityti, komentuoti projektą Peržiūrėti metaduomenis

prEN IEC 62364:2026 Viešoji apklausa

Komentavimo iki data 2026-04-08

Hidraulinės mašinos. Hidroabrazyvinės Kaplano, Franciso ir Peltono turbinų erozijos tyrimo gairės

Skaityti, komentuoti projektą Peržiūrėti metaduomenis

prEN 50726-3:2026 Viešoji apklausa

Komentavimo iki data 2026-04-12

Perspėjimo apie ekstremaliąsias situacijas ir pavojų sistemos. 3 dalis. Reagavimo į ekstremaliąsias situacijas ir pavojų sistemos. Rizikos valdymo byla ir taikymo pavyzdžiai

This document specifies the structure, construction, content and sequence of a technical risk management process and the technical risk management file in accordance with EN 50726-1. It also describes application examples for technical risk management according to EN 50726-1. An emergency and danger response system (EDRS) is used to minimize risks to life and limb. Its purpose is to report, verify and manage emergencies and dangers in order to prevent or limit personal injury. As already mentioned in the scope of application of EN 50726-1, the implementation of the Occupational Safety and Health Act and the subsequent regulations is intended in order to take particular account of the protection objective defined therein (physical integrity). However, this not only includes a risk assessment (e.g. prevention of acts of violence) for employees, but also for everyone in the property. The requirements of the Occupational Safety and Health Act are therefore intended to be observed when creating a safety concept and as part of the technical risk management process. Consequently, particular attention is drawn to paragraphs 5, 6 and 9 of the Occupational Safety and Health Act. Risks to life and limb can include emergencies and dangerous situations that can cause psychological or physical harm to people. As soon as the top management (e.g. operators, entrepreneurs, companies, approving authorities, building authorities, administrations) of a property has identified such risks to life and limb as part of risk management or similar risk assessments and/or independently became aware of them, this falls within the scope of EN 50726-1.

Skaityti, komentuoti projektą Peržiūrėti metaduomenis

prEN IEC 60034-18-31:2026 Viešoji apklausa

Komentavimo iki data 2026-04-03

Sukiosios elektros mašinos. 18-31 dalis. Funkcinis izoliacijos sistemų įvertinimas. Forminių apvijų bandymo procedūros. Sukiosiose mašinose naudojamų izoliacijos sistemų šiluminis įvertinimas ir klasifikavimas

Skaityti, komentuoti projektą Peržiūrėti metaduomenis

prEN IEC 63115-2:2026 Viešoji apklausa

Komentavimo iki data 2026-04-03

Antriniai elementai ir baterijos su šarminiais arba kitokiais nerūgštiniais elektrolitais. Sandarintieji įkraunamieji nikelio-metališkojo hidrido elementai ir moduliai, naudojami pramonėje. 2 dalis. Sauga

Skaityti, komentuoti projektą Peržiūrėti metaduomenis

prEN IEC 63115-1:2026 Viešoji apklausa

Komentavimo iki data 2026-04-03

Antriniai elementai ir baterijos su šarminiais arba kitokiais nerūgštiniais elektrolitais. Sandarintieji įkraunamieji nikelio-metališkojo hidrido elementai ir baterijos, naudojami pramonėje. 1 dalis. Eksploatacinės charakteristikos

Skaityti, komentuoti projektą Peržiūrėti metaduomenis

prEN IEC 61951-1:2026 Viešoji apklausa

Komentavimo iki data 2026-04-03

Antriniai elementai ir baterijos su šarminiais ar kitokiais nerūgštiniais elektrolitais. Nešiojamieji sandarieji antriniai elementai ir baterijos. 1 dalis. Nikelio-kadmio elementai

Skaityti, komentuoti projektą Peržiūrėti metaduomenis

prEN IEC 60749-29:2026 Viešoji apklausa

Komentavimo iki data 2026-04-03

Puslaidininkiniai įtaisai. Mechaninių ir klimatinių bandymų metodai. 29 dalis. Užsklendimo bandymas

Skaityti, komentuoti projektą Peržiūrėti metaduomenis

prEN IEC 60947-1:2026/prAA:2026 Viešoji apklausa

Komentavimo iki data 2026-04-01

Žemosios įtampos perjungimo ir valdymo įrenginiai. 1 dalis. Bendrosios taisyklės

Skaityti, komentuoti projektą Peržiūrėti metaduomenis

prEN IEC 60695-11-2:2026 Viešoji apklausa

Komentavimo iki data 2026-04-01

Gaisrinio pavojingumo bandymai. 11-2 dalis. Bandymo liepsnos. 1 kW galios paruošto mišinio liepsna. Aparatūra, patvirtinamojo bandymo tvarka ir nurodymai

Skaityti, komentuoti projektą Peržiūrėti metaduomenis

EN IEC 61442:2024/prA1:2026 Viešoji apklausa

Komentavimo iki data 2026-04-01

Vardinės nuo 6 kV (Um = 7,2 kV) iki 30 kV (Um = 36 kV) įtampos galios kabelių pagalbinių reikmenų bandymo metodai

Skaityti, komentuoti projektą Peržiūrėti metaduomenis

prEN IEC 60947-1:2026 Viešoji apklausa

Komentavimo iki data 2026-04-01

Žemosios įtampos perjungimo ir valdymo įrenginiai. 1 dalis. Bendrosios taisyklės

Skaityti, komentuoti projektą Peržiūrėti metaduomenis

Išplėstinė paieška

Rezultatai

Greitieji filtrai

Organizacija

Technikos komitetas

ICS

Būtini slapukai

Statistikos slapukai

El. pašto prenumerata

Standartų projektų sąrašas

Išplėstinė paieška

Rezultatai

Greitieji filtrai

Organizacija

Technikos komitetas

ICS