Standartų projektų sąrašas

Paieškos frazė

Išplėstinė paieška

Žymuo

Direktyvos

Organizacija

ICS

Technikos komitetas

Užsienio komitetas

Darbo grupė

Etapas

Būsena

Komentavimo data

iki

Rezultatai

prEN 12939 Viešoji apklausa

Komentavimo iki data 2025-12-18

Šiluminės statybinių medžiagų ir gaminių savybės. Šiluminės varžos nustatymas apsaugotos karštosios plokštės ir šilumos srauto matuoklio metodais. Stori didelės ir vidutinės šiluminės varžos gaminiai

This document specifies procedures to determine the thermal resistance of products whose thicknesses exceed the maximum thickness for guarded hot plate or heat flow meter apparatus. Most of the procedures described in this standard require apparatus that allows tests on specimens up to 100 mm thick . This document gives guidelines to assess the relevance of the thickness effect, i.e. to establish whether the thermal resistance of a thick product can or cannot be calculated as the sum of the thermal resistances of slices cut from the product, these guidelines complement the indications given in ISO 8302:1991[1] on the guarded hot plate apparatus. This document describes testing conditions which prevent the onset of convection which could take place in some products under the considered temperature differences and thicknesses.

Skaityti, komentuoti projektą Peržiūrėti metaduomenis

prEN 12667 Viešoji apklausa

Komentavimo iki data 2025-12-18

Šiluminės statybinių medžiagų ir gaminių savybės. Šiluminės varžos nustatymas apsaugotos karštosios plokštės ir šilumos srauto matuoklio metodais. Didelės ir vidutinės šiluminės varžos gaminiai

This document specifies principles and testing procedures for determining, by means of the guarded hot plate or heat flow meter methods, the thermal resistance of dry test specimens having a thermal resistance of not less than 0,5 m2·K/W. NOTE 1 The above limit is due to the effect of contact thermal resistances. An upper limit for measurable thermal resistance depends upon a number of factors described in this document, but a unique figure cannot be assigned. It applies in principle to any mean test temperature, but the equipment design in Annex D is essentially intended to operate between a minimum cooling unit temperature of -100 °C and maximum heating unit temperature of +100 °C. NOTE 2 Limits to the mean test temperature are only imposed by the materials used in the apparatus construction and by ancillary equipment. This document does not supply general guidance and background information (e.g. the heat transfer property to be reported, product-dependent specimen preparations, procedures requiring multiple measurements, such as those to assess the effect of specimen non-homogeneities, those to test specimens whose thickness exceeds the apparatus capabilities, and those to assess the relevance of the thickness effect). This document does not apply to cover measurements on moist products of any thermal resistance or measurements on thick products of high and medium thermal resistance.

Skaityti, komentuoti projektą Peržiūrėti metaduomenis

prEN 12664 Viešoji apklausa

Komentavimo iki data 2025-12-18

Šiluminės statybinių medžiagų ir gaminių charakteristikos. Šiluminės varžos nustatymas apsaugotos karštosios plokštės ir šilumos srauto matuoklio metodais. Vidutinės ir mažos šiluminės varžos sausi ir drėgni gaminiai

This document specifies principles and testing procedures for determining, by means of the guarded hot plate or heat flow meter methods, the thermal resistance of test specimens either in the dry state or conditioned to equilibrium with moist air, having a thermal resistance of not less than 0,1 m2·K/W and a (hygro)thermal transmissivity or thermal conductivity up to 2,0 W/(m·K). NOTE The lower limit for measurable thermal resistance is due to the effect of contact thermal resistances, which require special testing techniques described in this document. Although this document can be used for testing dry specimens of high and medium thermal resistance, i.e. on products having a thermal resistance, that is, on products with a thermal resistance of at least 0.5 m².K/W, the simpler procedures of EN 12667[3] are available for such specimen. This document does not cover methods to assess the hygrothermal transmissivity of materials in the over-hygroscopic range (i.e. when free liquid water occurs in the material in general above 95% of moisture). It applies in principle to any mean test temperature, but the equipment design in Annex D is essentially intended to operate between a minimum cooling unit temperature of -100 °C and maximum heating unit temperature of +100 °C. This document does not supply general guidance and background information (e.g. the heat transfer property to be reported, product-dependent specimen preparations, suggested materials for vapour-tight envelopes when testing moist specimens, procedures requiring multiple measurements, such as those to assess the effect of specimen non-homogeneities, those to test specimens whose thickness exceeds the apparatus capabilities, and those to assess the relevance of the thickness effect).

Skaityti, komentuoti projektą Peržiūrėti metaduomenis

prEN 18233 Viešoji apklausa

Komentavimo iki data 2025-11-04

ETICS rinkinyje esančių plokštelinių inkarų charakteristinio atsparumo apkrovoms ir charakteristinio plokštelių standžio nustatymas

This document covers the determination of the characteristic load resistance Fp and the characteristic plate stiffness kp of plate anchors.

Skaityti, komentuoti projektą Peržiūrėti metaduomenis

Būtini slapukai

Statistikos slapukai

El. pašto prenumerata

Išplėstinė paieška

Rezultatai

Greitieji filtrai

Organizacija

Technikos komitetas

ICS