List of drafts

prEN ISO 19980 Public enquiry

Comment end date 2026-10-15

Ophthalmic instruments - Corneal topographers (ISO/DIS 19980:2026)

This document specifies minimum requirements for instruments and systems that fall into the class of corneal topographers (CTs). It also specifies tests and procedures to verify that a system or instrument complies with this document and thus qualifies as a CT according to this document. It also specifies tests and procedures that allow the verification of capabilities of systems that are beyond the minimum requirements for CTs. This document defines terms that are specific to the characterization of the corneal shape so that they may be standardized throughout the field of vision care. This document is applicable to instruments, systems and methods that are intended to measure the surface shape of the cornea of the human eye. NOTE The measurements can be of the curvature of the surface in local areas, three-dimensional topographical measurements of the surface or other more global parameters used to characterize the surface. This document is not applicable to ophthalmic instruments classified as ophthalmometers.

Read draft and comment View

prEN IEC 62688:2026 Public enquiry

Comment end date 2026-09-09

Concentrator photovoltaic (CPV) modules and assemblies - Safety qualification

Read draft and comment View

prEN 50174-3:2026 Public enquiry

Comment end date 2026-09-04

Information technology - Cabling installation - Part 3: Installation planning and practices outside buildings

This document specifies requirements and provides recommendations for the following aspects of information technology cabling: a) planning; b) installation practice. This document is applicable to all types of information technology cabling outside buildings including generic cabling systems designed in accordance with EN 50173 series. The requirements and recommendations of this document can be applied to cabling that is defined as part of the building. The requirements and recommendations of Clauses 5, 6 and 7 of this document are subject to any site-specific requirements and recommendations of Clause 8. The planning of the pathway systems, spaces and structures within the core and access network cabling as described in Figure 2 that are owned by access providers is excluded except for requirements and recommendations that provide basic safety, function and environmental objectives for mechanical, ingress and climatic characteristics (i.e. excluding pathway dimensions, distribution of spaces and similar constraints based on specific transmission methods). The installation practices applicable to all cabling installation methods are included by the provision of the necessary planning requirements and recommendations associated with each one with the exception of information technology cabling installed: – around or within aerial power supply or associated earth conductors; – on infrastructures carrying power supplies in excess of AC/DC 25 kV. This document: 1) details the considerations for satisfactory installation and operation of information technology cabling; 2) excludes specific requirements applicable to other cabling systems (e.g. power supply cabling); however, it takes account of the effects other cabling systems may have on the installation of information technology cabling (and vice versa) and gives general advice; 3) excludes those aspects of installation associated with the transmission of signals in free space between transmitters, receivers or their associated antenna systems (e.g. wireless, radio, microwave or satellite). This document is applicable to certain hazardous environments. It does not exclude additional requirements which are applicable in particular circumstances, defined by e.g. electricity supply and electrified railways. The requirements within this document cover any additional requirements for the information technology cables installed in hazardous or stressful environments e.g. electricity supply and electric railway locations (see Clause 8). Safety (electrical safety and protection, optical power, fire protection, etc.) and electromagnetic compatibility (EMC) requirements are outside the scope of this document and are covered by other standards and regulations. However, information given in this document can be of assistance in meeting these standards and regulations. Examples of areas covered by this document are shown in Figure 2.

Read draft and comment View

prEN 12457-2 Public enquiry

Comment end date 2026-09-15

Granular waste materials, sludges, soil, soil-like materials and sediments - Leaching - Compliance test for leaching - Part 2: One-stage batch test at a liquid-to-solid ratio of 10L/kg for materials with particle size below 4 mm (with or without size reduction)

This document in the series specifies a compliance test providing information on leaching of granular waste materials, sludges, soil, soil-like materials and sediments under the experimental conditions specified hereafter, and particularly a liquid to solid ratio of 10 L/kg dry matter. It applies to materials which have a particle size below 4 mm without or with size reduction. This document has been developed to investigate the leaching of inorganic and non-volatile organic substances from granular waste materials, sludges, soil, soil-like materials and sediments. It does not take into account the consequences of microbiological processes in organic degradable materials. The test procedure specified in this document produces an eluate which is subsequently characterized physically and chemically according to appropriate standard methods. This document includes two different procedures for eluate preparation prior to analysis, one procedure for non-volatile organic substances, inorganic substances and DOC and one for inorganic substances and DOC. When assessing only the leaching of inorganic substances and DOC, certain precautions are needed when assessing the leaching of organic substances can in some cases be omitted. This procedure cannot be applied to materials with a water content or such a water affinity that a good mixing of the solid with the predetermined quantity of liquid is not achievable. This procedure does not apply to materials reacting with the leachant, leading, for example, to excessive gas emission, a solidifying effect or an excessive heat release. In that case, the material can be wetted prior to carrying out the leaching test. This test cannot be used alone to determine the leaching behaviour of granular waste materials, sludges, soil, soil-like materials and sediments, as specified in EN 12920. This document does not address issues related to health and safety.

Read draft and comment View

prEN 16723 Public enquiry

Comment end date 2026-10-01

Biomethane and other renewable and low-carbon methane rich gases - Specifications for injection in the natural gas network and for mixtures with natural gas as automotive fuel

This document specifies for - renewable and low-carbon methane rich gases for injection in the gas network - natural gas, renewable and low-carbon methane rich gases and mixtures thereof as fuel for engines This documents also specifies necessary related methods for sampling, analysis, and testing. This document applies to the previously mentioned gases irrespective of the storage state (compressed or liquefied). To check compliance with some requirements set by the standard, LNG or liquefied biomethane should be re-gasified prior to testing.

Read draft and comment View

EN 1991-1-4:2026/prA1 Public enquiry

Comment end date 2026-10-15

Eurocode 1 - Actions on structures - Part 1-4: Wind actions

1.1 Scope of EN 1991-1-4 (1) This document gives rules for the determination of natural wind actions for the structural design of building and civil engineering works for each of the loaded areas under consideration. This includes actions applied to the whole structure or parts of it, as well as wind-exposed elements attached to the structure. (2) This document is applicable to: - buildings and other civil engineering works with heights up to 200 m; - guyed masts, other open lattice structures and chimneys with heights up to 300 m; - bridges having no span greater than 200 m. (3) The rules contained in this document allow the evaluation of characteristic wind actions on land-based structures. (4) This document is applicable to offshore coastal structures. NOTE Additional or amended provisions can be necessary. (5) This document does not give guidance on non-synoptic winds (e.g. thunderstorms, downbursts, microbursts, tornadoes, etc.), mixed wind climates, nor does it give guidance on how to account for local effects (e.g. thermal effects, funnelling, strong arctic thermal surface inversion, etc.). (6) This document addresses simplified procedures for dynamic effects, mostly based on the assumption of a dominant single-mode response (see Annex E, Annex F and Annex G). General criteria for performing a full dynamic analysis under aerodynamic excitation are not treated in this document. (7) Wind pressure effects of passing vehicles are outside the scope of this document. NOTE See EN 1991 2 for wind effects from passing trains. 8) This document also provides guidance on wind tunnel testing and numerical modelling which can be needed or desirable when the shape or structural behaviour are unusual or do not strictly fall within the rules of the document, or in cases of unusual orography or other surroundings. 1.2 Assumptions (1) The assumptions given in EN 1990-1:2023+A1:2026, 1.2 apply.

Read draft and comment View

prEN ISO 45001 Archived

Comment end date 2026-08-25

Occupational health and safety management systems - Requirements with guidance for use (ISO/DIS 45001:2026)

This document specifies requirements for an occupational health and safety (OH&S) management system, to enable organizations to provide safe and healthy workplaces by preventing work-related injury, and ill health, as well as by proactively improving its OH&S performance. This document is applicable to any organization that wishes to establish, implement and maintain an OH&S management system to improve OH&S, eliminate hazards, minimize OH&S risks, take advantage of OH&S opportunities, and address OH&S management system nonconformities associated with its activities and promote work-related well-being. This document helps an organization to achieve the intended results of its OH&S management system which include: a) continual improvement of OH&S performance; b) fulfilment of legal requirements and other requirements; c) achievement of OH&S objectives. This document is applicable to any organization regardless of its size, type and activities. It is applicable to the OH&S risks under the organization’s control, and OH&S opportunities, taking into account factors such as the context in which the organization operates and the needs and expectations of its workers and other interested parties. This document does not state specific criteria for OH&S performance, nor is it prescriptive about the design of an OH&S management system. This document does not address issues such as product safety, property damage or environmental impacts, beyond the OH&S risks to workers and other relevant interested parties. This document can be used in whole or in part to systematically improve occupational health and safety management. However, claims of conformity to this document are not acceptable unless all its requirements are incorporated into an organization’s OH&S management system and fulfilled without exclusion.

View

prEN ISO 3675 Public enquiry

Comment end date 2026-09-03

Crude petroleum and liquid petroleum products - Laboratory determination of density - Hydrometer method (ISO/DIS 3675:2026)

Read draft and comment View

prEN 301 443 V2.2.0 (2026-07) Public enquiry

Comment end date 2026-09-28

Satellite Earth Stations and Systems (SES); Very Small Aperture Terminal (VSAT); Transmit-only, transmit-and-receive, receive-only satellite earth stations operating in the 4 GHz and 6 GHz frequency bands; Harmonised Standard for access to radio spectrum

Read draft and comment View

EN 1991-1-6:2026/prA1 Public enquiry

Comment end date 2026-09-24

Eurocode 1 - Actions on structures - Part 1-6: Actions during execution

1.1 Scope of prEN 1991-1-6 (1) prEN 1991-1-6 provides guidance and general rules on the determination of actions relevant for the design of buildings and civil engineering works, including geotechnical structures, for their execution stage. NOTE Actions for design during execution include those that only arise from execution activities and act during execution, termed construction actions (for example personnel and hand tools, auxiliary structures, equipment and elements used during execution), and others that are present during the service life of the completed structure (for example self-weight, wind, etc.) but which can act differently and/or have different values during execution. (2) prEN 1991-1-6 provides guidance and general rules for the determination of actions for the design of auxiliary structures, elements and equipment used during execution in case they are designed to the Eurocodes and not to other European Standards. NOTE Other European Standards (e.g. EN 12810, EN 12811, EN 12812) provide specific rules for certain types of auxiliary structures, equipment and elements used during execution. (3) prEN 1991-1-6 gives rules for buildings and bridges during execution to supplement the provisions in EN 1990. NOTE For combination rules for execution, see EN 1990. 1.2 Assumptions (1) The general assumptions given in EN 1990 apply. (2) The application of this document follows the limit state principle and is based on the partial factor method, unless explicitly prescribed differently. (3) The verification of buildings and civil engineering structures in transient design situations is undertaken in accordance with the Eurocodes, accounting for the interaction with any auxiliary structures, elements and/or equipment. (4) When using European product standards covering auxiliary structures, equipment and elements used during execution, it is assumed that the design basis, design requirements and, if provided, the safety and operational design limits specified in these product standards are taken into account. (5) Adequate planning, documentation, communication, control and supervision are provided during execution, involving all relevant parties. NOTE Execution of a structure can involve interaction between several parties from diverse engineering fields, responsible for the design, fabrication, transportation and execution of different subsystems used during the execution of a structure.

Read draft and comment View

prEN 15376 Public enquiry

Comment end date 2026-10-22

Automotive fuels - Ethanol as a blending component for petrol - Requirements and test methods

This document specifies requirements and test methods for marketed and delivered ethanol to be used as an extender for automotive fuel for petrol engine vehicles in accordance with the requirements of EN 228 [5]. It is applicable to ethanol used for blending at all levels up to and including 85 % (V/V). NOTE For the purposes of this document, the term “% (m/m)” and “% (V/V)” are used to represent respectively the mass fraction, µ, and the volume fraction, φ.

Read draft and comment View

prEN IEC 62149-13:2026 Archived

Comment end date 2026-08-26

Fibre optic active components and devices - Performance standards - Part 13: Performance specification template for pump laser diode modules

View

prEN ISO/IEC 27007 Public enquiry

Comment end date 2026-09-01

Information security, cybersecurity and privacy protection - Guidelines for information security management systems auditing (ISO/IEC DIS 27007:2026)

This document provides guidance on managing an information security management system (ISMS) audit programme, on conducting audits, and on the competence of ISMS auditors, in addition to the guidance contained in ISO 19011. This document is applicable to those needing to understand or conduct internal or external audits of an ISMS or to manage an ISMS audit programme.

Read draft and comment View

prEN ISO 17516 Public enquiry

Comment end date 2026-09-19

Cosmetics - Microbiology - Microbiological limits (ISO/DIS 17516:2026)

ISO 17516:2014 is applicable for all cosmetics and assists interested parties in the assessment of the microbiological quality of the products. Microbiological testing does not need to be performed on those products considered to be microbiologically low risk.

Read draft and comment View

prEN IEC 60216-4:2026 Public enquiry

Comment end date 2026-10-02

Electrical insulating materials - Thermal endurance properties - Part 4: Ageing ovens

Read draft and comment View

prEN 304 623 V0.1.3 (2026-06) New

Comment end date 2026-08-31

Cyber Security (CYBER); CRA; Cybersecurity requirements for boot managers

Read draft and comment View

prEN ISO/IEC 27018 Public enquiry

Comment end date 2026-09-04

Information security, cybersecurity and privacy protection - Guidelines for protection of personally identifiable information (PII) in public clouds acting as PII processors (ISO/IEC 27018:2025)

This document establishes commonly accepted control objectives, controls and guidelines for implementing measures to protect personally identifiable information (PII) in line with the privacy principles in ISO/IEC 29100 for the public cloud computing environment. In particular, this document specifies guidelines based on ISO/IEC 27002:2022, taking into consideration the regulatory requirements for the protection of PII which can be applicable within the context of the information security risk environment(s) of a provider of public cloud services. This document is applicable to all types and sizes of organizations, including public and private companies, government entities and not-for-profit organizations, which provide information processing services as PII processors via cloud computing under contract to other organizations. The guidelines in this document can also be relevant to organizations acting as PII controllers.

View

prEN ISO/IEEE 11073-10419 Public enquiry

Comment end date 2026-09-21

Health informatics - Personal health device communication - Part 10419: Device specialization - Insulin pump (ISO/IEEE FDIS 11073-10419:2026)

This standard establishes a normative definition of communication between personal telehealth insulin pump devices (agents) and managers (e.g., cell phones, personal computers, personal health appliances, set top boxes) in a manner that enables plug-and-play interoperability. It leverages work done in other ISO/IEEE 11073 standards including existing terminology, information profiles, application profile standards, and transport standards. It specifies the use of specific term codes, formats, and behaviors in telehealth environments, restricting optionality in base frameworks in favor of interoperability. This standard defines a common core functionality of personal telehealth insulin pump devices. In the context of personal health devices (PHDs), an insulin pump is a medical device used for the administration of insulin in the treatment of diabetes mellitus, also known as continuous subcutaneous insulin infusion (CSII) therapy. This standard provides the data modeling according to ISO/IEEE 11073-20601 and does not specify the measurement method.

Read draft and comment View

EN ISO 12855:2025/prA1 Public enquiry

Comment end date 2026-10-03

Electronic fee collection - Information exchange between service provision and toll charging - Amendment 1 (ISO 12855:2025/DAM 1:2026)

Read draft and comment View

prEN IEC 61000-4-4:2026 Public enquiry

Comment end date 2026-09-02

Electromagnetic compatibility (EMC) - Part 4-4: Testing and measurement techniques - Electrical fast transient/burst immunity test

Read draft and comment View

prEN 3155-065 Public enquiry

Comment end date 2026-09-08

Aerospace series - Electrical contacts used in elements of connection - Part 065: Contacts, electrical, male, type A, crimp, class S, size 8 Product standard

This document specifies the required characteristics, tests and tooling applicable to male electrical contacts, type A, crimp, class S, size 8, used in elements of connection in accordance with EN 3155-002 (this contact can be fitted in connectors EN 3645 series and EN 4165 series). It can be used together with EN 3155-001. The associated female contacts are specified in EN 3155-083.

Read draft and comment View

prEN IEC 62087-8:2026 Public enquiry

Comment end date 2026-09-27

Audio, video, and related equipment - Determination of power consumption - Part 8: Small network equipment

Read draft and comment View

prEN ISO/IEC 42006 Public enquiry

Comment end date 2026-10-10

Information technology - Artificial intelligence - Requirements for bodies providing audit and certification of artificial intelligence management systems (ISO/IEC 42006:2025)

This document specifies additional requirements to ISO/IEC 17021-1. The requirements contained in this document, when implemented, support the demonstration of competence, consistency and reliability by the bodies performing auditing and certification of an artificial intelligence management system (AIMS) according to ISO/IEC 42001 for organizations that provide, develop or use AI systems. Certification of AIMS is a third-party conformity assessment activity (as described in ISO/IEC 17000:2020, 4.5), and bodies performing this activity are third-party conformity assessment bodies. This document also provides the necessary information and confidence to customers about the way certification has been granted. NOTE This document can be used as a criteria document for accreditation or peer assessment.

Read draft and comment View

prEN IEC 62282-2-400:2026 Public enquiry

Comment end date 2026-10-04

Fuel cell technologies - Part 2-400: Fuel cell modules - Calculation of rated power and power density of a PEM stack and PEM module

Read draft and comment View

prEN ISO 13297-1 Public enquiry

Comment end date 2026-09-08

Small craft - Alternating and direct current installations of electrical systems - Part 1: Single-phase AC, Craft low voltage DC (ISO/DIS 13297-1:2026)

This document specifies the requirements for the design, construction and installation of the following types of DC and AC electrical systems, installed on small craft either individually or in combination: a) extra-low-voltage direct current (DC) electrical systems that operate at nominal potentials of 50 V DC or less; b) single-phase alternating current (AC) systems that operate at a nominal voltage not exceeding AC 250 V. This document does not cover the following: — electrical propulsion systems of direct current less than 1 500 V DC, single-phase alternating current up to 1 000 V AC, and three-phase alternating current up to 1 000 V AC, which are addressed by ISO 16315; — any conductor that is part of an outboard engine assembly and that does not extend beyond the outboard engine manufacturers supplied cowling; — three-phase AC installations that operate at a nominal voltage not exceeding 500 V AC, which are addressed by IEC 60092-507.

Read draft and comment View

Extended search

Results

Quick filters

Organisation

Technical Committee

ICS

Mandatory cookies

Statistics cookies

Newsletter subscription

List of drafts

Extended search

Results

Quick filters

Organisation

Technical Committee

ICS