List of drafts

prEN IEC 62087-8:2026 Public enquiry

Comment end date 2026-09-27

Audio, video, and related equipment - Determination of power consumption - Part 8: Small network equipment

Read draft and comment View

prEN ISO/IEC 42006 Public enquiry

Comment end date 2026-10-10

Information technology - Artificial intelligence - Requirements for bodies providing audit and certification of artificial intelligence management systems (ISO/IEC 42006:2025)

This document specifies additional requirements to ISO/IEC 17021-1. The requirements contained in this document, when implemented, support the demonstration of competence, consistency and reliability by the bodies performing auditing and certification of an artificial intelligence management system (AIMS) according to ISO/IEC 42001 for organizations that provide, develop or use AI systems. Certification of AIMS is a third-party conformity assessment activity (as described in ISO/IEC 17000:2020, 4.5), and bodies performing this activity are third-party conformity assessment bodies. This document also provides the necessary information and confidence to customers about the way certification has been granted. NOTE This document can be used as a criteria document for accreditation or peer assessment.

Read draft and comment View

prEN IEC 62282-2-400:2026 Public enquiry

Comment end date 2026-10-04

Fuel cell technologies - Part 2-400: Fuel cell modules - Calculation of rated power and power density of a PEM stack and PEM module

Read draft and comment View

prEN IEC 55014-1 [fra4]:2026 Public enquiry

Comment end date 2026-09-02

Electromagnetic compatibility - Requirements for household appliances, electric tools and similar apparatus - Part 1: Emission

Read draft and comment View

prEN IEC 60601-2-36:2026 Public enquiry

Comment end date 2026-09-16

Medical electrical equipment - Part 2-36: Particular requirements for the basic safety and essential performance of equipment for extracorporeally induced lithotripsy

View

EN 1794-2:2024/prA1 Public enquiry

Comment end date 2026-10-01

Road traffic noise reducing devices - Non-acoustic performance - Part 2: Methods of determination of the general safety and environmental characteristics

This document specifies methods and criteria for assessing the general safety and environmental performance of road traffic noise reducing devices under typical roadside conditions. Appropriate test methods are provided where these are necessary. The treatment of each topic is covered separately in Annexes A to F.

Read draft and comment View

prEN 196-17 Public enquiry

Comment end date 2026-10-13

Method of testing cement - Part 17: Determination glass content of granulated blast furnace slag as constituent for common cement

This document describes two equivalent test methods for determining the glass content in Granulated blast furnace Slag (GBS) as constituent for common cement as defined on EN 197-1. Method A - Method of determining the glass content of GBS by X-ray diffraction. Method B - Method of determining the glass content of GBS by polarized optical microscopy. The glass content (or glassy/amorphous phase) in GBS is the fraction of the material that lacks a crystalline structure, having solidified rapidly from the melt in the form of amorphous glass. It is usually expressed as a percentage (wt%) of the total slag. In the absence of a product standard or a specification in the product standard, the constituent is tested at the fineness of the intended use. Furthermore, these test methods are used in manufacturing control of cement constituents for assessing their conformity to the limit indicated in EN 197-1.

Read draft and comment View

prEN 12697-14 Public enquiry

Comment end date 2026-10-08

Bituminous mixtures - Test methods - Part 14: Water content

This document describes a test method for the determination of the water content of samples of bituminous mixtures. The test method is suitable for checking conformity to a product specification, where required. Exposure levels are related to both handling procedures and ventilation provision and it is emphasized that adequate training should be given to staff employed in the usage of these substances.

Read draft and comment View

prEN IEC 60335-2-48:2026/prAA:2026 Public enquiry

Comment end date 2026-09-02

Household and similar electrical appliances - Safety - Part 2-48: Particular requirements for commercial electric grillers and toasters

This European Standard deals with the safety of electrically operated commercial grillers and toasters not intended for household use. The rated voltage being not more than 250 V for single-phase appliances connected between one phase and neutral, and 480 V for other appliances. Rotary or continuous grillers and toasters and similar appliances intended for grilling by radiant heat such as rotisseries, salamanders, etc. are within the scope of this standard. Appliances within the scope of this standard are typically used in restaurants, canteens, hospitals and commercial enterprises such as bakeries, butcheries, etc.

Read draft and comment View

prEN ISO 25177 Public enquiry

Comment end date 2026-09-08

Soil quality — Field soil description

This document provides guidance on the description of soil in the field and its environmental context. It is applicable to natural, near-natural, urban and industrial sites. The soil observations and measurements can be made on a project site level, on a plot level, on layer or horizon level and on specific soil constituents. It also provides guidance on how to describe layers of anthropogenic (artificial) material or layers that were not modified by pedogenic processes in the strict sense and how to describe coarse material of natural or artificial origin. This document can be used in combination with other publications that provide guidance or requirements regarding specific aspects of soil observations and measurements. NOTE 1 It might not be possible or necessary to record data under all the headings listed in Clauses 4 to 11. NOTE 2 Overall guidance for presentation of information from soil surveys is given in ISO 15903. NOTE 3 The guidance provided assumes that sampling will be done in accordance with ISO 18400.

Read draft and comment View

prEN 10048 Public enquiry

Comment end date 2026-09-24

Hot-rolled narrow steel strip - Tolerances on dimensions and shape

This document specifies tolerances on dimensions and shape for hot rolled uncoated narrow strip and cut lengths of non-alloy and alloy steel grades in accordance with Table 1. It is usually produced in thickness of 0,8 mm up to and including 16 mm and generally has a rolled width less than 600 mm but is also produced in rolled widths up to and including 720 mm. Hot-rolled narrow strip has a symmetrical thickness profile with tight crown tolerances and therefore cannot be compared to slit wide strip. This document also applies to hot-rolled strip for cold rolling. Table 1 — Field of application [...table not represented...] This document can also be used for other steels, e.g.: steels from standards not mentioned in Table 1. This document does not apply to: — continuously hot-rolled wide strip and plate/sheet cut from wide strip of non-alloy and alloy steels and narrow strip obtained by slitting wide strip (EN 10051); — hot-rolled patterned steel strip and plate/sheet cut from wide strip (see EN 10363); — uncoated or electrolytically coated cold rolled sheet and strip (see EN 10131); — hot-dip coated steel sheet and strip (EN 10143).

Read draft and comment View

prEN ISO 19980 Public enquiry

Comment end date 2026-10-15

Ophthalmic instruments - Corneal topographers (ISO/DIS 19980:2026)

This document specifies minimum requirements for instruments and systems that fall into the class of corneal topographers (CTs). It also specifies tests and procedures to verify that a system or instrument complies with this document and thus qualifies as a CT according to this document. It also specifies tests and procedures that allow the verification of capabilities of systems that are beyond the minimum requirements for CTs. This document defines terms that are specific to the characterization of the corneal shape so that they may be standardized throughout the field of vision care. This document is applicable to instruments, systems and methods that are intended to measure the surface shape of the cornea of the human eye. NOTE The measurements can be of the curvature of the surface in local areas, three-dimensional topographical measurements of the surface or other more global parameters used to characterize the surface. This document is not applicable to ophthalmic instruments classified as ophthalmometers.

Read draft and comment View

prEN IEC 62688:2026 Public enquiry

Comment end date 2026-09-09

Concentrator photovoltaic (CPV) modules and assemblies - Safety qualification

Read draft and comment View

prEN 50174-3:2026 Public enquiry

Comment end date 2026-09-04

Information technology - Cabling installation - Part 3: Installation planning and practices outside buildings

This document specifies requirements and provides recommendations for the following aspects of information technology cabling: a) planning; b) installation practice. This document is applicable to all types of information technology cabling outside buildings including generic cabling systems designed in accordance with EN 50173 series. The requirements and recommendations of this document can be applied to cabling that is defined as part of the building. The requirements and recommendations of Clauses 5, 6 and 7 of this document are subject to any site-specific requirements and recommendations of Clause 8. The planning of the pathway systems, spaces and structures within the core and access network cabling as described in Figure 2 that are owned by access providers is excluded except for requirements and recommendations that provide basic safety, function and environmental objectives for mechanical, ingress and climatic characteristics (i.e. excluding pathway dimensions, distribution of spaces and similar constraints based on specific transmission methods). The installation practices applicable to all cabling installation methods are included by the provision of the necessary planning requirements and recommendations associated with each one with the exception of information technology cabling installed: – around or within aerial power supply or associated earth conductors; – on infrastructures carrying power supplies in excess of AC/DC 25 kV. This document: 1) details the considerations for satisfactory installation and operation of information technology cabling; 2) excludes specific requirements applicable to other cabling systems (e.g. power supply cabling); however, it takes account of the effects other cabling systems may have on the installation of information technology cabling (and vice versa) and gives general advice; 3) excludes those aspects of installation associated with the transmission of signals in free space between transmitters, receivers or their associated antenna systems (e.g. wireless, radio, microwave or satellite). This document is applicable to certain hazardous environments. It does not exclude additional requirements which are applicable in particular circumstances, defined by e.g. electricity supply and electrified railways. The requirements within this document cover any additional requirements for the information technology cables installed in hazardous or stressful environments e.g. electricity supply and electric railway locations (see Clause 8). Safety (electrical safety and protection, optical power, fire protection, etc.) and electromagnetic compatibility (EMC) requirements are outside the scope of this document and are covered by other standards and regulations. However, information given in this document can be of assistance in meeting these standards and regulations. Examples of areas covered by this document are shown in Figure 2.

Read draft and comment View

prEN 12457-2 Public enquiry

Comment end date 2026-09-15

Granular waste materials, sludges, soil, soil-like materials and sediments - Leaching - Compliance test for leaching - Part 2: One-stage batch test at a liquid-to-solid ratio of 10L/kg for materials with particle size below 4 mm (with or without size reduction)

This document in the series specifies a compliance test providing information on leaching of granular waste materials, sludges, soil, soil-like materials and sediments under the experimental conditions specified hereafter, and particularly a liquid to solid ratio of 10 L/kg dry matter. It applies to materials which have a particle size below 4 mm without or with size reduction. This document has been developed to investigate the leaching of inorganic and non-volatile organic substances from granular waste materials, sludges, soil, soil-like materials and sediments. It does not take into account the consequences of microbiological processes in organic degradable materials. The test procedure specified in this document produces an eluate which is subsequently characterized physically and chemically according to appropriate standard methods. This document includes two different procedures for eluate preparation prior to analysis, one procedure for non-volatile organic substances, inorganic substances and DOC and one for inorganic substances and DOC. When assessing only the leaching of inorganic substances and DOC, certain precautions are needed when assessing the leaching of organic substances can in some cases be omitted. This procedure cannot be applied to materials with a water content or such a water affinity that a good mixing of the solid with the predetermined quantity of liquid is not achievable. This procedure does not apply to materials reacting with the leachant, leading, for example, to excessive gas emission, a solidifying effect or an excessive heat release. In that case, the material can be wetted prior to carrying out the leaching test. This test cannot be used alone to determine the leaching behaviour of granular waste materials, sludges, soil, soil-like materials and sediments, as specified in EN 12920. This document does not address issues related to health and safety.

Read draft and comment View

prEN 16723 Public enquiry

Comment end date 2026-10-01

Biomethane and other renewable and low-carbon methane rich gases - Specifications for injection in the natural gas network and for mixtures with natural gas as automotive fuel

This document specifies for - renewable and low-carbon methane rich gases for injection in the gas network - natural gas, renewable and low-carbon methane rich gases and mixtures thereof as fuel for engines This documents also specifies necessary related methods for sampling, analysis, and testing. This document applies to the previously mentioned gases irrespective of the storage state (compressed or liquefied). To check compliance with some requirements set by the standard, LNG or liquefied biomethane should be re-gasified prior to testing.

Read draft and comment View

EN 1991-1-4:2026/prA1 Public enquiry

Comment end date 2026-10-15

Eurocode 1 - Actions on structures - Part 1-4: Wind actions

1.1 Scope of EN 1991-1-4 (1) This document gives rules for the determination of natural wind actions for the structural design of building and civil engineering works for each of the loaded areas under consideration. This includes actions applied to the whole structure or parts of it, as well as wind-exposed elements attached to the structure. (2) This document is applicable to: - buildings and other civil engineering works with heights up to 200 m; - guyed masts, other open lattice structures and chimneys with heights up to 300 m; - bridges having no span greater than 200 m. (3) The rules contained in this document allow the evaluation of characteristic wind actions on land-based structures. (4) This document is applicable to offshore coastal structures. NOTE Additional or amended provisions can be necessary. (5) This document does not give guidance on non-synoptic winds (e.g. thunderstorms, downbursts, microbursts, tornadoes, etc.), mixed wind climates, nor does it give guidance on how to account for local effects (e.g. thermal effects, funnelling, strong arctic thermal surface inversion, etc.). (6) This document addresses simplified procedures for dynamic effects, mostly based on the assumption of a dominant single-mode response (see Annex E, Annex F and Annex G). General criteria for performing a full dynamic analysis under aerodynamic excitation are not treated in this document. (7) Wind pressure effects of passing vehicles are outside the scope of this document. NOTE See EN 1991 2 for wind effects from passing trains. 8) This document also provides guidance on wind tunnel testing and numerical modelling which can be needed or desirable when the shape or structural behaviour are unusual or do not strictly fall within the rules of the document, or in cases of unusual orography or other surroundings. 1.2 Assumptions (1) The assumptions given in EN 1990-1:2023+A1:2026, 1.2 apply.

Read draft and comment View

prEN ISO 19085-11 Public enquiry

Comment end date 2026-09-10

Woodworking machines - Safety - Part 11: Combined machines (ISO/DIS 19085‑11:2026)

This document specifies the safety requirements and measures for combined woodworking machines (defined in 3.1), capable of continuous production use, with manual loading and unloading of the workpiece and hereinafter referred to also as “machines”. The machines are designed to cut solid wood and material with similar physical characteristics to wood (see ISO 19085-1:2021, 3.2). This document deals with all significant hazards, hazardous situations and events, listed in Annex A, relevant to the machines, when operated, adjusted and maintained as intended and under the conditions foreseen by the manufacturer; reasonably foreseeable misuse has been considered too. Transport, assembly, dismantling, disabling and scrapping phases have also been taken into account. This document applies to machines also equipped with the devices or additional working units listed in the Scopes of ISO 19085-5:2024, ISO 19085-6:2024, ISO 19085-7:2024 and ISO 19085-9:2024. This document does not apply to: a) machines incorporating a planing unit and a mortising device only; NOTE Machines incorporating a planing unit and a mortising device only are dealt with in ISO 19085-7:2024. b) combined machines incorporating a band saw unit; c) machines with a mortising unit with a separate drive other than the planing unit drive; d) machines intended for use in potentially explosive atmosphere; e) machines manufactured before the publication of this document.

Read draft and comment View

prEN IEC 62841-4-14:2026 Public enquiry

Comment end date 2026-09-16

Electric motor-operated hand-held tools, transportable tools and lawn and garden machinery - Safety - Part 4-14: Particular requirements for pruning saws

Read draft and comment View

prEN 10111 Public enquiry

Comment end date 2026-10-11

Continuously hot rolled low carbon steel sheet and strip for cold forming - Technical delivery conditions

This European Standard specifies the grades of continuously hot rolled low carbon steel sheet and strip (in coils) for cold forming. Depending on its actual width, strip is classified as: - hot rolled wide strip if its width is greater than or equal to 600 mm; - hot rolled slit wide strip if its width is less than 600 mm. For each grade, it specifies the chemical composition and the mechanical properties. This European Standard is applicable to products of thickness not less than 1,0 mm and not exceeding 11 mm. This European Standard is not applicable to products covered by other standards, such as: - hot rolled products of non-alloy structural steels for general use (see EN 10025 all parts); - steel sheet for pressure purposes (see EN 10028 all parts); - steel sheet for welded gas cylinders (see EN 10120); - quenched and tempered steels (see EN 10083-1 and EN 10083-2).

Read draft and comment View

EN 10338:2025/prA1 Public enquiry

Comment end date 2026-10-18

Hot rolled and cold rolled non-coated products of multiphase steels for cold forming - Technical delivery conditions

This document applies to hot rolled and cold rolled non-coated steel flat products made of multiphase steels for cold forming. It covers cold rolled products of thicknesses t < 3 mm and hot rolled products of thicknesses t ≤ 6,5 mm. These products are delivered in sheet, hot rolled strip, slit hot rolled strip, cold strip, slit cold rolled strip or cut lengths obtained from slit wide strip. Flat products of multiphase steels for cold forming can be delivered with an electrolytic zinc coating according to EN 10152.

Read draft and comment View

prEN ISO 19085-6 Public enquiry

Comment end date 2026-09-10

Woodworking machines - Safety - Part 6: Single spindle vertical moulding machines (toupie) (ISO/DIS 19085-6:2026)

This document specifies the safety requirements and measures for single spindle vertical moulding machines (defined in 3.1), capable of continuous production use and hereinafter referred to also as “machines”. The machines are designed to cut solid wood and material with similar physical characteristics to wood. This document deals with all significant hazards, hazardous situations and events as listed in Annex A, relevant to the machines when they are operated, adjusted and maintained as intended and under the conditions foreseen by the manufacturer including reasonably foreseeable misuse. Transport, assembly, dismantling, disabling and scrapping phases have also been taken into account. This document is also applicable to machines fitted with one or more of the following devices/additional working units, whose hazards have been dealt with: a) device to adjust the arbor vertically; b) device to tilt the arbor; c) device to fit a manually operated tenoning sliding table; d) glass bead saw unit; e) adjustable table insert; f) device for changing the direction of rotation of the spindle; g) device for fixing shank mounted tools on the arbor; h) interchangeable arbor; i) quick tool/arbor change system; j) demountable power feed unit; k) support for the demountable power feed unit with power-driven adjustments. This document does not apply to — machines equipped with outboard bearings, — machines equipped with powered movements of a front extension table and/or a tenoning sliding table. This document is not applicable to machines intended for use in potentially explosive atmospheres or to machines manufactured prior to the date of its publication.

Read draft and comment View

prEN 304 627 V1.0.1 (2026-07) Public enquiry

Comment end date 2026-09-20

Cyber Security (CYBER); CRA; Cybersecurity requirements for routers, modems intended for the connection to the internet, and switches

Read draft and comment View

prEN 304 634 V1.0.0 (2026-07) Public enquiry

Comment end date 2026-10-11

Cyber Security (CYBER); CRA; Cybersecurity requirements for personal wearable

Read draft and comment View

prEN 304 624 V1.0.0 (2026-08) Public enquiry

Comment end date 2026-10-18

Cyber Security (CYBER); CRA; Cybersecurity requirements for Public key infrastructure and digital certificate issuance software

Read draft and comment View

Extended search

Results

Quick filters

Organisation

Technical Committee

ICS

Mandatory cookies

Statistics cookies

Newsletter subscription

List of drafts

Extended search

Results

Quick filters

Organisation

Technical Committee

ICS