Standartų projektų sąrašas | Standartų projektų portalas

GPDR

Privatumo politika

EN

Paieškos frazė

Išplėstinė paieška

Žymuo

Direktyvos

Organizacija

ICS

Technikos komitetas

Užsienio komitetas

Darbo grupė

Etapas

Būsena

Komentavimo data

iki

Rezultatai

prEN 1487 Viešoji apklausa

Komentavimo iki data 2026-11-23

Pastatų armatūra. Hidraulinės saugos įtaisai. Bandymai ir reikalavimai

This document specifies dimensions, materials and performance requirements, including methods of test, for hydraulic safety groups, of nominal sizes from DN 15 to DN 25, having working pressures from 0,1 MPa (1 bar) to 1,0 MPa (10 bar). Hydraulic safety groups are intended for fitting to the potable water supply of storage water heaters, having a maximum storage temperature of 95 °C. Hydraulic safety groups limit the pressure in hot water heaters, prevent the backflow of water into the main circuit and prevent the discharged water to get into contact with the water in the water heater. Hydraulic safety groups do not control the temperature. They ensure the hydraulic safety of water heaters if the mechanical resistance of the water heater remains at least equal to the rating pressure. NOTE The use of the device specified in this document does not override the need to use controls (e.g. thermostats and cut-outs) which act directly on the power sources of water heaters (for more information see Annex A).

Skaityti, komentuoti projektą Peržiūrėti metaduomenis

prEN 1213 Viešoji apklausa

Komentavimo iki data 2026-11-22

Pastatų armatūra. Metaliniai pastatų geriamojo vandens vandentiekio uždarymo čiaupai. Bandymai ir reikalavimai

This document is applicable to metallic stop valves for use with water intended for human consumption. This document specifies: — requirements for the design of stop valves; — mechanical, hydraulic and acoustic requirements; — test methods; — marking requirements. This document is applicable to metallic stop valves, dimensions DN 10 to DN 100, for potable water installation in buildings for PN10 or PN16 and a distribution temperature of 65 °C. This document is applicable to stop valves in combination with accessories in the same body. This document is not applicable to regulating or servicing valves, designed specially to isolate sanitary tapware or other sanitary appliances.

Skaityti, komentuoti projektą Peržiūrėti metaduomenis

prEN 17821 Viešoji apklausa

Komentavimo iki data 2026-11-22

Pastatų armatūra. Šalčiui atsparūs lauke naudojami čiaupai. Bendroji techninė specifikacija

This document specifies application, general construction, performance and material requirements for frost resistant taps for outdoor use (FRT), PN 10. This document is applicable to potable water installations with a static pressure of maximum 1,0 MPa (10 bar) and a distribution temperature of maximum 25 °C (PWC). NOTE See Annex A for a general overview of this document’s organization and test sequence.

Skaityti, komentuoti projektą Peržiūrėti metaduomenis

prEN 1488 Viešoji apklausa

Komentavimo iki data 2026-11-22

Pastatų armatūra. Plėtimosi saugos įtaisai. Bandymai ir reikalavimai

This document specifies, dimensions, materials and performance requirements (including methods of test) for expansion groups, of nominal sizes from DN 15 to DN 25, having working pressures from 0,1 MPa (1 bar) to 1,0 MPa (10 bar). Expansion groups are fitted to the cold potable water supply only for expansion purposes, e.g. of storage water heaters, having a maximum distribution temperature of 95 °C. Expansion groups limit pressure in the water heater to which they are fitted, that is produced by thermal expansion of the water, prevent the backflow of water into the supply pipe and prevent the discharged water to get into contact with the water in the water heater. Expansion groups do not control temperature and alone do not constitute the protection required for storage water heaters. NOTE The use of the device specified in this document does not override the need to use controls (e.g. thermostats and thermal cut-outs) which act directly on the power sources of water heaters (for more information see Annex A).

Skaityti, komentuoti projektą Peržiūrėti metaduomenis

prEN 1491 Viešoji apklausa

Komentavimo iki data 2026-11-22

Pastatų armatūra. Plėtimosi saugos vožtuvai. Bandymai ir reikalavimai

This document specifies dimensions, materials and performance requirements (including methods of test) for expansion valves, of nominal sizes from DN 15 to DN 50, having working pressures ) from 0,1 MPa (1 bar) to 1,0 MPa (10 bar). Expansion valves are intended for fitting to the cold potable water supply of storage water heaters, having a maximum distribution temperature of 95 °C, for all energy sources. Expansion valves do not control the temperature and alone do not constitute the protection required for storage water heaters. Expansion valves limit pressure, in the water heaters to what they are fitted, that is produced by thermal expansion of the water. NOTE The use of the device specified in this document does not override the need to use controls (e.g. thermostats and cut-outs) which act directly on the power sources of water heaters (for more information see Annex A).

Skaityti, komentuoti projektą Peržiūrėti metaduomenis

prEN 1489 Viešoji apklausa

Komentavimo iki data 2026-11-22

Pastatų armatūra. Slėgio saugos vožtuvai. Bandymai ir reikalavimai

This document specifies dimensions, materials and performance requirements, including methods of test, for pressure safety valves, of nominal sizes from DN 15 to DN 40, having working pressures from 0,1 MPa (1 bar) to 1,0 MPa (10 bar). Pressure safety valves are intended for fitting to the potable water supply of storage water heaters, having a maximum storage temperature of 95 °C. Pressure safety valves limit the pressure in hot water heaters. Pressure safety valves do not control the temperature and alone do not constitute the protection required for storage water heaters. They are not intended to act as expansion valves under normal conditions. NOTE The use of the device specified in this document does not override the need to use controls (e.g. thermostats and cut-outs) which act directly on the power sources of water heaters (for more information see Annex A).

Skaityti, komentuoti projektą Peržiūrėti metaduomenis

prEN 18380 Viešoji apklausa

Komentavimo iki data 2026-11-01

Vandens ruošimo įranga, įrengiama pastatų viduje. Įtaisai su UV šviesos diodais. Eksploataciniai, saugos ir bandymų reikalavimai

This document specifies definitions, principles of construction, requirements and methods for testing the performance of UV devices (240 nm to 290 nm nominal) for potable water installations according to EN 806-2 which are permanently connected to the building’s supply. Devices described by this document can be installed at the point of entry (POE), within the water distribution system inside the building or at the point of use (POU). Additionally, the devices described in this document can be used in mobile or temporary potable water installations, where the system is not permanently connected to a water supply. UV devices in the sense of this document are UV bactericidal treatment devices or UV disinfection devices for one of three specified water qualities, determined by the observed UV transmittance. Devices can be standalone, integrated into a larger appliance or part of multi-staged treatment process. The document relates solely to the performance of the UV reactor.

Skaityti, komentuoti projektą Peržiūrėti metaduomenis