Standartų projektų sąrašas

prEN IEC 61010-2-033:2026 Viešoji apklausa

Komentavimo iki data 2026-11-22

Saugos reikalavimai, keliami elektrinei matavimo, valdymo ir laboratorinei įrangai. 2-033 dalis. Ypatingieji reikalavimai, keliami buitinės ir profesinės paskirties rankiniams multimetrams ir kitokiems tinklo įtampos matuokliams

Skaityti, komentuoti projektą Peržiūrėti metaduomenis

prEN IEC 61010-2-032:2026 Viešoji apklausa

Komentavimo iki data 2026-11-22

Saugos reikalavimai, keliami elektrinei matavimo, valdymo ir laboratorinei įrangai. 2-032 dalis. Ypatingieji reikalavimai, keliami elektriniams bandymams ir matavimams naudojamiems rankiniams ir ranka valdomiems srovės jutikliams

Skaityti, komentuoti projektą Peržiūrėti metaduomenis

prEN IEC 61010-2-030:2026 Viešoji apklausa

Komentavimo iki data 2026-11-22

Saugos reikalavimai, keliami elektrinei matavimo, valdymo ir laboratorinei įrangai. 2-030 dalis. Ypatingieji reikalavimai, keliami bandymo ar matavimo grandines turinčiai įrangai

Skaityti, komentuoti projektą Peržiūrėti metaduomenis

prEN IEC 61851-24:2026 Viešoji apklausa

Komentavimo iki data 2026-11-22

Elektrinių transporto priemonių laidžiojo galios ir energijos perdavimo sistemos. 24 dalis. Skaitmeninis ryšys tarp elektrinių transporto priemonių įkrovimo nuolatine srove įrangos ir elektrinės transporto priemonės įkrovimui nuolatine srove kontroliuoti

Skaityti, komentuoti projektą Peržiūrėti metaduomenis

prEN IEC 60269-100:2026 Viešoji apklausa

Komentavimo iki data 2026-11-22

Žemosios įtampos saugikliai. 100 dalis. Bendrieji reikalavimai ir bandymai

Skaityti, komentuoti projektą Peržiūrėti metaduomenis

prEN IEC 60598-2-4:2026 Viešoji apklausa

Komentavimo iki data 2026-11-22

Šviestuvai. 2-4 dalis. Ypatingieji reikalavimai. Nešiojamieji bendrosios paskirties šviestuvai

Skaityti, komentuoti projektą Peržiūrėti metaduomenis

prEN IEC 60335-2-65:2026/prAA:2026 Viešoji apklausa

Komentavimo iki data 2026-11-22

Buitiniai ir panašios paskirties elektriniai prietaisai. Sauga. 2-65 dalis. Ypatingieji reikalavimai, keliami oro valytuvams

This European Standard deals with the safety of electric air-cleaning appliances, their rated voltage being not more than 250 V for single phase and 480 V for other appliances, for household purposes. Also includes appliances intended to be used by laymen in shops, in light industry and on farms..

Skaityti, komentuoti projektą Peržiūrėti metaduomenis

prEN IEC 60335-2-65:2026 Viešoji apklausa

Komentavimo iki data 2026-11-22

Buitiniai ir panašios paskirties elektriniai prietaisai. Sauga. 2-65 dalis. Ypatingieji reikalavimai, keliami oro valytuvams

This European Standard deals with the safety of electric air-cleaning appliances, their rated voltage being not more than 250 V for single phase and 480 V for other appliances, for household purposes. Also includes appliances intended to be used by laymen in shops, in light industry and on farms..

Skaityti, komentuoti projektą Peržiūrėti metaduomenis

prEN IEC 60335-2-109:2026/prAA:2026 Viešoji apklausa

Komentavimo iki data 2026-11-22

Buitiniai ir panašios paskirties elektriniai prietaisai. Sauga. 2-109 dalis. Ypatingieji reikalavimai, keliami vandens apdorojimo ultravioletine spinduliuote prietaisams

This European Standard deals with the safety of UV radiation water treatment appliances for household and similar use, their rated voltage being not more than 250 V for single-phase appliances and 480 V for other appliances including direct current (DC) supplied appliances and battery-operated appliances

Skaityti, komentuoti projektą Peržiūrėti metaduomenis

prEN IEC 60335-2-109:2026 Viešoji apklausa

Komentavimo iki data 2026-11-22

Buitiniai ir panašios paskirties elektriniai prietaisai. Sauga. 2-109 dalis. Ypatingieji reikalavimai, keliami vandens apdorojimo ultravioletine spinduliuote prietaisams

This European Standard deals with the safety of UV radiation water treatment appliances for household and similar use, their rated voltage being not more than 250 V for single-phase appliances and 480 V for other appliances including direct current (DC) supplied appliances and battery-operated appliances

Skaityti, komentuoti projektą Peržiūrėti metaduomenis

prEN IEC 63514:2026 Viešoji apklausa

Komentavimo iki data 2026-11-22

Jūrų navigacinė ir radijo ryšio įranga bei sistemos. Labai aukštų dažnių juostoje veikiančios duomenų mainų sistemos. Laivų mobiliųjų stočių reikalavimai ir bandymo metodai

Skaityti, komentuoti projektą Peržiūrėti metaduomenis

prEN IEC 60825-18:2026 Viešoji apklausa

Komentavimo iki data 2026-11-22

Lazerinių gaminių sauga. 18 dalis. Nukreipiamosios lazerio pluošto sistemos

Skaityti, komentuoti projektą Peržiūrėti metaduomenis

ISO/IEC DIS 9798-5 Viešoji apklausa

Komentavimo iki data 2026-11-21

Informacijos saugumas. Objekto tapatumo nustatymas. 5 dalis. Informacijos neatskleidžiantys mechanizmai

Skaityti, komentuoti projektą Peržiūrėti metaduomenis

prEN ISO/IEEE 11073-10441 Viešoji apklausa

Komentavimo iki data 2026-11-21

Sveikatos informatika. Įtaisų funkcinis suderinamumas. 10441 dalis. Įtaiso specializavimas. Širdies ir kraujagyslių sistemos pajėgumo ir veiklos monitorius (ISO/IEEE FDIS 11073-10441:2026)

Within the context of the ISO/IEEE 11073 family of standards for device communication, a normative definition of communication between personal telehealth cardiovascular fitness and activity monitor devices and managers (e.g., cell phones, personal computers, personal health appliances, and set top boxes) is established in this standard in a manner that enables plug-and-play interoperability. Appropriate portions of existing standards are leveraged including ISO/IEEE 11073 terminology, information models, application profile standards, and transport standards. The use of specific term codes, formats, and behaviors in telehealth environments restricting optionality in base frameworks in favor of interoperability is specified. A common core of communication functionality for personal telehealth cardiovascular fitness and activity monitor devices is defined in this standard.

Skaityti, komentuoti projektą Peržiūrėti metaduomenis

prEN ISO 17078-1 Viešoji apklausa

Komentavimo iki data 2026-11-21

Naftos ir dujų pramonė, įskaitant mažesnio anglies dioksido pėdsako energijos gamybą. Gręžimo, gavybos ir injekavimo įranga. 1 dalis. Šerdys su šonine kišene (ISO/DIS 17078-1:2026)

ISO 17078:2004 provides requirements for side-pocket mandrels used in the petroleum and natural gas industry. This part of ISO 17078 includes specifying, selecting, designing, manufacturing, quality control, testing, and preparation for shipping of side-pocket mandrels. This part of ISO 17078:2004 does not address nor include requirements for end connections between the side-pocket mandrels and the well conduit. The installation and retrieval of side-pocket mandrels is outside the scope of this part of ISO 17078:2004. Additionally, this part of ISO 17078:2004 does not include specifications for centre-set mandrels, or mandrels that employ or support tubing-retrievable flow control devices. This part of ISO 17078:2004 does not include gas-lift or any other flow-control valves or devices, latches, and/or associated wire line equipment that can or cannot be covered in other ISO specifications. The side-pocket mandrels to which this part of ISO 17078:2004 refers are independent devices that can accept installation of flow-control or other devices down-hole.

Skaityti, komentuoti projektą Peržiūrėti metaduomenis

prEN 14359 Viešoji apklausa

Komentavimo iki data 2026-11-21

Hidropneumatiniai hidraulinių pavarų akumuliatoriai

1.1 This document specifies the requirements for materials, design, manufacture, testing inspection, safety equipment configuration and documentation (including instructions for first operation), for commonly-used types of gas-loaded accumulators and pressure vessels used to provide additional gas capacity for fluid power applications (see 1.2). 1.2 This document applies to the following types of components, defined as the pressure-containing envelope of gas-loaded accumulators: - bladder type; - diaphragm type; - piston type; - transfer type; - pressure vessels used to provide additional gas capacity. They consist of one or several parts joined together by a variety of mechanical means and by welding. 1.3 This document applies to gas-loaded accumulators which operate with the following conditions: - subject to an internal gauge pressure greater than 0,5 bar; - working temperature not lower than –50 °C and not higher than +200 °C; - containing all liquids and gases as defined in the European Legislation on Pressure Equipment, see Note. NOTE When the accumulator contains Group 1 liquids or gases, consideration relating to risks other than those required by the European Legislation on Pressure Equipment are not covered by this document and will be assessed separately.

Skaityti, komentuoti projektą Peržiūrėti metaduomenis

prEN IEC 61189-5-501:2026 Viešoji apklausa

Komentavimo iki data 2026-11-20

Elektrinių medžiagų, spausdintinių plokščių ir kitų sujungiamųjų darinių bei sąrankų bandymo metodai. 5-501 dalis. Bendrieji medžiagų ir sąrankų bandymo metodai. Litavimo fliusų paviršinės varžos bandymai

Skaityti, komentuoti projektą Peržiūrėti metaduomenis

EN IEC 60317-25:2020/prA1:2026 Viešoji apklausa

Komentavimo iki data 2026-11-20

Kai kurių tipų apvijinių laidų techniniai reikalavimai. 25 dalis. 200 klasės poliesteriu arba poliesterimidu dengtas ir poliamido imidu emaliuotas apvalusis aliumininis laidas. 1 keitinys

Skaityti, komentuoti projektą Peržiūrėti metaduomenis

EN 1994-1-2:2026/prA1 Viešoji apklausa

Komentavimo iki data 2026-11-19

Eurokodas 4. Kompozitinių plieninių-betoninių konstrukcijų projektavimas. 1-2 dalis. Konstrukcijų elgsenos ugnyje skaičiavimas

(1) EN 1994-1-2 gives rules for the design of steel-concrete composite structures for the accidental design situation of fire exposure. It only identifies differences from, or supplements to, rules for normal temperature design. (2) EN 1994-1-2 only applies to structures, or parts of structures, that are within the scope of EN1994-1-1 and are designed accordingly.

Skaityti, komentuoti projektą Peržiūrėti metaduomenis

EN 1994-2:2026/prA1 Viešoji apklausa

Komentavimo iki data 2026-11-19

Eurokodas 4. Kompozitinių plieninių-betoninių konstrukcijų projektavimas. 2 dalis. Tiltai

EN 1994-2 gives design rules for steel-concrete composite bridges or members of bridges, supplementary to the general rules given in EN 1994-1-1.

Skaityti, komentuoti projektą Peržiūrėti metaduomenis

EN 1994-1-1:2026/prA1 Viešoji apklausa

Komentavimo iki data 2026-11-19

Eurokodas 4. Kompozitinių plieninių-betoninių konstrukcijų projektavimas. 1-1 dalis. Bendrosios ir pastatų taisyklės

1.1 Scope of EN 1994-1-1 (1) EN 1994-1-1 gives general rules for the design of steel and concrete composite structures and supplementary provisions specific for buildings. NOTE Specific rules for bridges are given in EN 1994-2. 1.2 Assumptions (1) The assumptions of EN 1990-1 apply to EN 1994-1-1. (2) In addition to the general assumptions of EN 1990-1, the assumptions given in EN 1992-1-1, EN 1992-1-2, and EN 1993-1-1 apply to this document. (3) EN 1994-1-1 is intended to be used in conjunction with EN 1990-1, EN 1991 (all parts), EN 1992-1-1, EN 1993 (all parts), EN 1997 (all parts), EN 1998 (all parts when steel and concrete composite structures are built in seismic regions), EN 1090-1, EN 1090-2, EN 1090-4, EN 13670 and ENs for construction products relevant to steel and concrete composite structures.

Skaityti, komentuoti projektą Peržiūrėti metaduomenis

EN 1993-6:2026/prA1 Viešoji apklausa

Komentavimo iki data 2026-11-19

Eurokodas 3. Plieninių konstrukcijų projektavimas. 6 dalis. Kranus laikančios konstrukcijos

1.1 Scope of EN 1993-6 (1) EN 1993-6 provides rules for structural design of crane supporting structures. (2) EN 1993-6 is applicable to crane supporting structures, especially to indoor and outdoor overhead crane runway beams, of: a) overhead travelling cranes, either: — top-mounted cranes; — underslung cranes; b) monorail hoist blocks. NOTE The principles of the design rules can be applied to supporting structures of other types of cranes making due allowance for differences in the crane-induced actions, if exist. For example, the design rules for supporting structures of the cranes listed in (2) assume that the horizontal crane loads occur randomly scattered along the runways in general. This assumption does not apply to other cranes such as travelling wall jib cranes. (3) EN 1993-6 does not apply to the tracks and suspensions of light crane systems conforming to EN 16851, see Figure 1.1. NOTE The standardized tracks and suspensions of light crane systems are considered as parts of the crane. [Figure 1.1 — Light crane system] (4) Additional rules are given for ancillary runway items including crane rails, structural end stops, surge connectors and surge girders and for runway supporting structures. (5) EN 1993-6 does not apply to cranes and all other moving parts. NOTE Provisions for cranes are given in EN 13001 (all parts) in general and for bridge and gantry cranes in EN 15011 in particular. 1.2 Assumptions (1) Unless specifically stated, EN 1990-1, EN 1991 (all parts) and EN 1993-1 (all parts) apply. (2) The design methods given in EN 1993-6 are applicable if — the execution quality and tolerances are as specified in EN 1090-2, and; — the construction materials and products used are as specified in the relevant parts of EN 1993, or in the relevant material and product specifications. (3) Following interfaces between hoisting device and its supporting structure are assumed: a) the top of crane rail for top-mounted cranes; b) the top of flange on which the crane or hoist block operates for underslung cranes and monorail hoist blocks; c) the support points as shown in Figure 1.1 for light crane systems.

Skaityti, komentuoti projektą Peržiūrėti metaduomenis

EN 1993-1-6:2025/prA1 Viešoji apklausa

Komentavimo iki data 2026-11-19

Eurokodas 3. Plieninių konstrukcijų projektavimas. 1-6 dalis. Kevalinių konstrukcijų stipris ir stabilumas

1.1 Scope (1) EN 199316 provides rules for the structural design of plated steel structures that have the form of a shell of revolution (axisymmetric shell). (2) This document is applicable to unstiffened fabricated axisymmetric shells formed from isotropic rolled plates using both algebraic and computational procedures, and to stiffened axisymmetric shells with different wall constructions using computational procedures. It also applies to associated circular or annular plates and to beam section rings and stringer stiffeners where they form part of the complete shell structure. The general computational procedures are applicable to all shell forms. (3) This document does not apply to manufactured shells or to shell panels or to elliptical shell forms, except that its computational procedures are applicable to all shell structures. This document does not apply to structures under seismic or other dynamic loading. It does not cover the aspects of leakage of stored liquids or solids. (4) Cylindrical and conical panels are not explicitly covered by this document. However, the provisions of 9.8 can be used provided that appropriate boundary conditions are taken into account. (5) This document defines the characteristic and design values of the resistance of the structure. (6) This document is concerned with the requirements for design against the ultimate limit states of: — plastic failure; — cyclic plasticity; — buckling; — fatigue. (7) Overall equilibrium of the structure (sliding, uplifting, overturning) is not included in this document. Special considerations for specific applications are included in the relevant application parts of EN 1993. (8) Detailed formulae for the simple calculation of unstiffened cylinders, cones and spherical domes are given in the Annexes. (9) Provisions for simple calculations on specific stiffened shell types are given in EN 199341. (10) This document is intended for application to steel shell structures. Where no standard exists for shell structures made of other metals, including high strength steels, the provisions of this document are applicable provided the appropriate material properties of the metal are taken into account. (11) The provisions of this document are intended to be applied within the temperature ranges defined in the relevant EN 1993 application parts. (12) Where no application part defines a different range, this document applies to structures within the following limits: — design metal temperatures lie within the range −50 °C to +100 °C, except when using the special provisions given in 5.1; — radius to thickness ratios (r/t) within the range 50 to 2 000; — manufactured circular hollow sections according to EN 10210 and EN 10219 are outside the scope of this document and are covered by EN 199311. However, if no other provisions are available, the rules of this document are useful for manufactured circular hollow sections. In particular, this document is applicable to the design of manufactured piles (see EN 19935) provided the imperfections and tolerance requirements of EN 19935 are adopted in place of those specified in this document, and where no other standard covers the specific pile geometry. NOTE 1 Experimental and theoretical data relating to manufactured circular hollow sections were not considered when this document was drafted. The application of this document to such structures therefore remains the responsibility of the user. NOTE 2 The stress design rules of this document can be rather conservative if applied to some geometries and loading conditions for relatively thickwalled shells. NOTE 3 Thinner shells than r/t = 2 000 can be treated using these provisions but the provisions have not been verified for such thin shells. NOTE 4 The maximum temperature is restricted so that the influence of creep can be ignored where high temperature creep effects are not covered by the relevant application part. [...]

Skaityti, komentuoti projektą Peržiūrėti metaduomenis

EN 1993-4-1:2026/prA1 Viešoji apklausa

Komentavimo iki data 2026-11-19

Eurokodas 3. Plieninių konstrukcijų projektavimas. 4-1 dalis. Silosai

1.1 Scope of EN 1993 4 1 (1) prEN 1993 4 1 provides rules for the structural design of steel silos of circular or rectangular plan-form, being free-standing (on ground) or supported on a structural framework (elevated). (2) prEN 1993 4 1 is applicable to silos constructed from isotropic rolled plates that are stiffened or unstiffened, from corrugated sheeting that is stiffened or unstiffened and from flat or corrugated plates assembled into box structures of different geometries. It applies to vertical walls, hoppers, roof structures, transition junctions and support structures. (3) prEN 1993 4 1 does not apply to storage vessels for silage and haylage, or to the storage of materials that are not free-flowing (see EN 1991 4). This Part 4-1 also does not cover: - resistance to fire; - cylindrical silos with internal subdivisions; - internal structures within a single silo (except for internal ties, as defined in 12.5); - silos with capacity less than 100 kN (10 tonnes); - hoppers that are supported on a structural framework; - cases where special measures are necessary to limit the consequences of accidents. (4) This document is applicable to silos within the following dimensional limits (see EN 1991-4): - Silo aspect ratio hb/dc < 10 - Silo total height hb < 70 m - Silo equivalent diameter dc < 60 m NOTE These dimensional limitations are more limited than those of EN 1991-4 which also applies to silos constructed from other materials. (5) Where this standard applies to circular planform silos, the geometric form is restricted to axisymmetric structures, but unsymmetrical actions on them and supports that induce forces in the silo structure that are not axisymmetric are included. (6) This part is concerned only with the requirements for resistance and stability of steel silos. For other requirements (such as operational safety, functional performance, fabrication and erection, quality control, details like man-holes, flanges, filling devices, outlet gates and feeders, etc.), see other relevant standards and information. (7) This part is concerned with both isolated silo structures and silos that are connected to others to form a battery of silos, but throughout this document the term silo refers to a single cell within a battery. (8) Provisions relating to special requirements of seismic design are provided in EN 1998 4, which complements or adapts the provisions of Eurocode 3 specifically for this purpose. (9) The structural design of supporting structures for the silo are dealt with in EN 1993 1 1. The supporting structure is deemed to consist of all structural elements beneath the bottom flange of the lowest ring of the silo (see Figure 1.1), though information on some forms of support structure is given in Clause 8 of this document. (10) Foundations in reinforced concrete for steel silos are dealt with in EN 1992 (all parts) and EN 1997 (all parts). 1.2 Assumptions (1) Unless specifically stated, the provisions of EN 1990, EN 1991 (all parts) and EN 1993 1 (all parts) apply. (2) The design methods given in EN 1993 4 1 are applicable if: - the execution quality is as specified in EN 1090 2, and - the construction materials and products used are as specified in the relevant parts of EN 1993 (all parts), or in the relevant material and product specifications. Figure 1.1 - Terminology used in silo structures ...

Skaityti, komentuoti projektą Peržiūrėti metaduomenis

prEN ISO 25379-2 Viešoji apklausa

Komentavimo iki data 2026-11-19

In vitro diagnostikai taikomos naujos kartos sekoskaitos (NGS) veiksmų eiga. 2 dalis. Žmogaus RNR tyrimas

This document specifies requirements and gives recommendations for next generation sequencing (NGS) workflows. This document covers the pre-examination processes, human RNA isolation, sequencing library preparation, sequencing, sequence analysis and reporting of the examination of sequences for diagnostic purposes from isolated RNA from, e.g. formalin-fixed and paraffin embedded tissues, fresh frozen tissues, fine needle aspirates (FNA), whole blood, circulating tumour cells (CTCs), exosomes and other extracellular vesicles, and circulating cell free RNA from plasma. NOTE 1 Typical applications include, but are not limited to, NGS for oncology and clinical genetics, certain single-cell analyses. This document is addressing in vitro diagnostic examinations including laboratory developed tests and is applicable to medical laboratories, molecular pathology laboratories and molecular genetic laboratories, in vitro diagnostic developers and manufacturers, biobanks as well as institutions and organizations performing biomedical research or sequencing services. This document is not applicable for in situ sequencing, forensic sequencing, sequencing of pathogens or microorganisms and microbiome analysis. NOTE 2 International, national or regional regulations or requirements or multiples of them can also apply to specific topics covered in this document.

Skaityti, komentuoti projektą Peržiūrėti metaduomenis

Išplėstinė paieška

Rezultatai

Greitieji filtrai

Organizacija

Technikos komitetas

ICS

Būtini slapukai

Statistikos slapukai

El. pašto prenumerata

Standartų projektų sąrašas

Išplėstinė paieška

Rezultatai

Greitieji filtrai

Organizacija

Technikos komitetas

ICS