Standartų projektų sąrašas

Paieškos frazė

Išplėstinė paieška

Žymuo

Direktyvos

Organizacija

ICS

Technikos komitetas

Užsienio komitetas

Darbo grupė

Etapas

Būsena

Komentavimo data

iki

Rezultatai

prEN ISO 19085-15 Viešoji apklausa

Komentavimo iki data 2026-10-04

Medienos apdirbimo mašinos. Sauga. 15 dalis. Presai (ISO/DIS 19085-15:2026)

1.1 This document specifies the safety requirements and measures for — cold presses, — hot presses, — bending presses, — edge/face gluing presses, — membrane presses, and — embossing presses, where the pressing force is applied by hydraulic, pneumatic or electrical actuators pushing two flat or shaped surfaces against each other, capable of continuous production use, altogether referred to as “machines”. This document deals with all significant hazards, hazardous situations and events as listed in Annex A, relevant to machines, when operated, adjusted and maintained as intended and under the conditions foreseen by the manufacturer, including reasonably foreseeable misuse. Also, transport, assembly, dismantling, disabling and scrapping phases are taken into account. 1.2 This document is applicable to machines fitted with one or more of the following devices or additional working units, whose hazards have been dealt with: a) a device for hot gluing; b) a device for high-frequency gluing in the frequency range from 1 MHz to 400 MHz; c) a device for high-frequency shaping in the frequency range from 1 MHz to 400 MHz; d) an automatic workpiece loading and unloading system; e) an intermediate additional platen; f) a workpiece extractor; g) a horizontal pressing system; h) split moveable platens. 1.3 The machines are designed to process workpieces consisting of: a) solid wood; b) materials with similar characteristics to wood (see ISO 19085-1:2021, 3.2), except those with light alloy laminates/edges/profiles for high-frequency presses; c) wood-based material such as chipboard, fibreboard and plywood composed/laminated with steel sheets/edges/profiles, except for high-frequency presses; d) honeycomb board; e) composite boards made from the materials listed above. 1.4 This document does not deal with any hazards related to: — specific devices that differ from the list above; — hot fluid heating systems internal to the machine other than electrical; — any hot fluid heating systems external to the machine; — operation of taking intermediate platens out and in again; — the combination of a single machine being used with any other machine (as part of a line). 1.5 This document is not applicable to: — frame presses; — membrane presses where the pressing force is applied by vacuum only; — presses for producing chipboard, fibreboard, OSB; — machines intended for use in potentially explosive atmosphere; — machines manufactured before the date of publication of this document.

Skaityti, komentuoti projektą Peržiūrėti metaduomenis

prEN ISO 19085-12 Viešoji apklausa

Komentavimo iki data 2026-08-25

Medienos apdirbimo mašinos. Sauga. 12 dalis. Dygiapjovės ir (arba) profiliavimo staklės (ISO/DIS 19085-12:2026)

This document specifies the safety requirements and measures for manually loaded and unloaded — single-end tenoning machines with a manual feed sliding table, — single-end tenoning machines with a mechanical feed sliding table, — single-end tenoning-profiling machines with mechanical feed, — double-end tenoning-profiling machines with mechanical feed, also designed to be automatically either loaded or unloaded, or both, and — angular systems for tenoning and profiling with mechanical feed with maximum workpiece height capacity of 200 mm for single-end machines and 500 mm for double-end machines, capable of continuous production use, altogether referred to as “machines”. This document deals with all significant hazards, hazardous situations and events as listed in Annex A, relevant to machines, when operated, adjusted and maintained as intended and under the conditions foreseen by the manufacturer including reasonably foreseeable misuse. Also, transport, assembly, dismantling, disabling and scrapping phases have been taken into account. The machines are designed to process in one pass one end or two sides, either opposite or perpendicular to each other, of workpieces made of a) solid wood, and b) materials with similar physical characteristics to wood (see ISO 19085-1:2021, 3.2); and c) only the machines with mechanical feed, made of d) fibre-cement, e) rock wool and glass wool, f) gypsum, g) plasterboard, h) matrix engineered mineral boards, silicate boards and sulfate boards, i) composite materials with core consisting of polyurethane or mineral material laminated with light alloy, j) polymer-matrix composite materials and reinforced thermoplastic, thermoset and elastomeric materials, k) aluminium light alloy profiles, and l) composite boards made from the materials listed above. This document is also applicable to machines fitted with one or more of the following devices or additional working units, whose hazards have been dealt with: — sanding units; — fixed or movable workpiece support; — automatic tool changing; — automatic workpiece returner; — glass bead saw unit; — hinge recessing unit; — boring unit; — dynamic processing unit; — sawing unit installed out of the integral enclosure, between machine halves in double-end machines; — foiling unit; — coating unit; — grooving unit with a milling tool installed out of the integral enclosure, between machine halves; — brushing unit; — gluing unit; — sealing unit; — dowels inserting unit; — tongues inserting unit; — inkjet marking unit; — laser marking unit; — labelling unit; — workpiece back-up device (device that is either anti-chipping or anti-splintering, or both); — quick tool changing system; — post-formed edge pre-cutting unit; — additional workpiece support (at either infeed or outfeed, or both); — parallel infeed device on single-end machines; — transversal infeed device on single-end machines; — intermediate workpiece support on double-end machines; — automatic infeed device; — feed chain with dogs. This document does not deal with any hazards related to: a) systems for automatic loading and unloading of the workpiece to a single machine other than automatic workpiece returner; b) single machine being used in combination with any other machine (as

Skaityti, komentuoti projektą Peržiūrėti metaduomenis

Būtini slapukai

Statistikos slapukai

El. pašto prenumerata

Išplėstinė paieška

Rezultatai

Greitieji filtrai

Organizacija

Technikos komitetas

ICS