Standartų projektų sąrašas

Paieškos frazė

Išplėstinė paieška

Žymuo

Direktyvos

Organizacija

ICS

Technikos komitetas

Užsienio komitetas

Darbo grupė

Etapas

Būsena

Komentavimo data

iki

Rezultatai

EN 1999-1-1:2023/prA1 Viešoji apklausa

Komentavimo iki data 2026-05-28

Eurokodas 9. Aliumininių konstrukcijų projektavimas. 1-1 dalis. Bendrosios taisyklės

EN 1999-1-1 gives basic design rules for structures made of wrought aluminium alloys and limited guidance for cast alloys (see Clause 5 and Annex C). This document does not cover the following, unless otherwise explicitly stated in this document: - members with material thickness less than 0,6 mm; - welded members with material thickness less than 1,5 mm; - connections with: - steel bolts and pins with diameter less than 5 mm; - aluminium bolts and pins with diameter less than 8 mm; - rivets and thread forming screws with diameter less than 3,9 mm.

Skaityti, komentuoti projektą Peržiūrėti metaduomenis

EN 1999-1-4:2023/prA1 Viešoji apklausa

Komentavimo iki data 2026-05-28

Eurokodas 9. Aliumininių konstrukcijų projektavimas. 1-4 dalis. Šaltai formuoti lakštiniai konstrukcijų profiliuočiai

1.1 Scope of EN 1999-1-4 (1) EN 1999-1-4 gives design requirements for cold-formed trapezoidal aluminium sheeting. It applies to cold-formed aluminium products made from hot rolled or cold rolled sheet or strip that have been cold-formed by such processes as cold-rolled forming or press-breaking. NOTE 1 The rules in this part complement the rules in other parts of EN 1999-1. NOTE 2 The execution of aluminium structures made of cold-formed structures for roof, ceiling, floor and wall applications is covered in EN 1090-5. (2) EN 1999-1-4 gives methods for stressed-skin design using aluminium sheeting as a structural diaphragm. (3) EN 1999-1-4 does not apply to cold-formed aluminium profiles like C- and Z- profiles nor cold-formed and welded circular or rectangular hollow sections. (4) EN 1999-1-4 gives methods for design by calculation and for design assisted by testing. The methods for the design by calculation apply only within stated ranges of material properties and geometrical properties for which sufficient experience and test evidence is available. These limitations do not apply to design by testing. (5) EN 1999-1-4 does not cover load arrangement for loads during execution and maintenance. 1.2 Assumptions (1) For the design of new structures, EN 1999 is intended to be used, for direct application, together with EN 1990, EN 1991, EN 1992, EN 1993, EN 1994, EN 1995, EN 1997 and EN 1998. EN 1999 is intended to be used in conjunction with: - European Standards for construction products relevant for aluminium structures; - EN 1090-1, Execution of steel structures and aluminium structures - Part 1: Requirements for conformity assessment of structural components; - EN 1090-5, Execution of steel structures and aluminium structures - Part 5: Technical requirements for cold-formed structural aluminium elements and cold-formed structures for roof, ceiling, floor and wall applications.

Skaityti, komentuoti projektą Peržiūrėti metaduomenis

EN 1999-1-2:2023/prA1 Viešoji apklausa

Komentavimo iki data 2026-05-28

Eurokodas 9. Aliumininių konstrukcijų projektavimas. 1-2 dalis. Konstrukcijų elgsenos ugnyje skaičiavimas

1.1 Scope of EN 1999-1-2 (1) EN 1999-1-2 deals with the design of aluminium structures for the accidental situation of fire exposure and is intended to be used in conjunction with EN 1999-1-1, EN 1999-1-2, EN 1999-1-3, EN 1999-1-4 and EN 1999-1-5. This document only identifies differences from, or supplements to, normal temperature design. (2) EN 1999-1-2 applies to aluminium structures required to fulfil a load bearing function. (3) EN 1999-1-2 gives principles and application rules for the design of structures for specified requirements in respect of the aforementioned function and the levels of performance. (4) EN 1999-1-2 applies to structures, or parts of structures, that are within the scope of EN 1999 1 1 and are designed accordingly. (5) The methods given in EN 1999-1-2 are applicable to the following aluminium alloys: EN AW-3004 - H34 EN AW-5083 - O and H12 EN AW-6063 - T5 and T6 EN AW-5005 - O and H34 EN AW-5454 - O and H34 EN AW-6082 - T4 and T6 EN AW-5052 - H34 EN AW-6061 - T6 (6) The methods given in EN 1999-1-2 are applicable also to other aluminium alloy/tempers of EN 1999 1-1, if reliable material properties at elevated temperatures are available or the simplified assumptions in 5.2.1 are applied. 1.2 Assumptions (1) In addition to the general assumptions of EN 1990, the following assumptions apply: - the choice of the relevant design fire scenario is made by appropriate qualified and experienced personnel, or is given by the relevant national regulation. - any active and passive fire protection systems taken into account in the design will be adequately maintained. (2) EN 1999 is intended to be used in conjunction with: - European Standards for construction products relevant for aluminium structures - EN 1090-1, Execution of steel structures and aluminium structures - Part 1: Requirements for conformity assessment of structural components - EN 1090-3, Execution of steel structures and aluminium structures - Part 3: Technical requirements for aluminium structures

Skaityti, komentuoti projektą Peržiūrėti metaduomenis

Būtini slapukai

Statistikos slapukai

El. pašto prenumerata

Išplėstinė paieška

Rezultatai

Greitieji filtrai

Organizacija

Technikos komitetas

ICS