Standartų projektų sąrašas

Paieškos frazė

Išplėstinė paieška

Žymuo

Direktyvos

Organizacija

ICS

Technikos komitetas

Užsienio komitetas

Darbo grupė

Etapas

Būsena

Komentavimo data

iki

Rezultatai

prEN ISO 19629 Viešoji apklausa

Komentavimo iki data 2026-08-27

Techninė keramika (modernioji keramika, modernioji techninė keramika). Termofizikinės keraminių kompozitų savybės. Vienmačio temperatūrinio laidžio nustatymas blyksnio metodu (ISO/DIS 19629:2026)

This document describes the flash method for the determination of thermal diffusivity of ceramic matrix composites with continuous fibre reinforcement. In order to conform with the unidimensional heat transfer hypothesis, the experimental conditions are defined such that the material behaves in a homogeneous manner. This involves performing tests in one symmetry axis of the composite. The method is applicable to materials which are physically and chemically stable during the measurement, and covers the range of temperature from 100 K to 2 800 K. It is suitable for the measurement of thermal diffusivity values in the range 10−4 m2∙s−1 to 10−7 m2∙s−1.

Skaityti, komentuoti projektą Peržiūrėti metaduomenis

prEN 843-3 Viešoji apklausa

Komentavimo iki data 2026-08-13

Modernioji techninė keramika. Monolitinės keramikos mechaninės savybės kambario temperatūroje. 3 dalis. Subkritinio pleišėjimo parametrų nustatymas lenkiamojo stiprio bandymais, išlaikant pastovią tempimo spartą

This document specifies a method for the determination of subcritical crack growth parameters of advanced monolithic technical ceramics in the temperature range 15 °C to 30 °C by measuring the dependence of mean flexural strength on the rate of loading. The method is based on strength test procedures described in EN 843 1. The applicability of this method is limited by specific requirements for a low scatter of the initial strength of the test pieces and an upper limit of the stress load rate for the data points considered. This document is not applicable to test pieces with artificially introduced flaws or cracks.

Skaityti, komentuoti projektą Peržiūrėti metaduomenis

prEN 843-9 Viešoji apklausa

Komentavimo iki data 2026-07-30

Modernioji techninė keramika. Monolitinės keramikos mechaninės savybės kambario temperatūroje. 9 dalis. Bandymo metodas nustatyti atsparumą kraštų atsilupimui

This document specifies two test methods for the determination of the resistance of the edges of brittle ceramic materials to be damaged by chipping. This document is applicable to homogeneous monolithic ceramics with flat surfaces and straight sharp or chamfered edges.

Skaityti, komentuoti projektą Peržiūrėti metaduomenis

prEN 820-5 Viešoji apklausa

Komentavimo iki data 2026-07-23

Modernioji techninė keramika. Monolitinės keramikos termomechaninės savybės. 5 dalis. Tampros modulių nustatymas aukštoje temperatūroje

This part of EN 820 describes methods for determining the elastic moduli, specifically Young's modulus, shear modulus and Poisson's ratio, of advanced monolithic technical ceramics at temperatures above room temperature. The standard prescribes three alternative methods for determining some or all of these three parameters: A the determination of Young's modulus by static flexure of a thin beam in three- or four-point bending. B the determination of Young's modulus by forced longitudinal resonance, or Young's modulus, shear modulus and Poisson's ratio by forced flexural and torsional resonance, of a thin beam. C the determination of Young's modulus from the fundamental natural frequency of a struck bar (impulse excitation method). This part of EN 820 extends the above-defined room-temperature methods described in EN 843-2 to elevated temperatures. All the test methods assume the use of homogeneous test pieces of linear elastic materials. The test assumes that the test piece has isotropic elastic properties. At high porosity levels all of the methods can become inappropriate. The maximum grain size (see EN 623-3), excluding deliberately added whiskers, should be less than 10 % of the minimum dimension of the test piece. NOTE 1 Method C in EN 843-2 based on ultrasonic time of flight measurement has not been incorporated into this part of EN 820. Although the method is feasible to apply, it is specialised, and outside the capabilities of most laboratories. There are also severe restrictions on test piece geometries and methods of achieving pulse transmission. For these reasons this method has not been included in EN 820-5. NOTE 2 The upper temperature limit for this test depends on the properties of the test pieces, and can be limited by softening within the timescale of the test. In addition, for method A there can be limits defined by the choice of test jig construction materials.

Skaityti, komentuoti projektą Peržiūrėti metaduomenis

prEN 843-2 Viešoji apklausa

Komentavimo iki data 2026-07-23

Modernioji techninė keramika. Monolitinės keramikos mechaninės savybės kambario temperatūroje. 2 dalis. Jungo modulio, šlyties modulio ir Puasono koeficiento nustatymas

This part of EN 843 specifies methods for determining the elastic moduli, specifically Young’s modulus, shear modulus and Poisson’s ratio, of advanced monolithic technical ceramics at room temperature. This European Standard prescribes four alternative methods for determining some or all of these three parameters: A The determination of Young’s modulus by static flexure of a thin beam in three- or four-point flexure. B The determination of Young’s modulus by forced longitudinal resonance, or Young’s modulus, shear modulus and Poisson’s ratio by forced flexural and torsional resonance, of a thin beam. C The determination of Young’s modulus, shear modulus and Poisson’s ratio from the time-of-flight of an ultrasonic pulse. D The determination of Young’s modulus from the fundamental natural frequency of a struck bar (impulse excitation method). All the test methods assume the use of homogeneous test pieces of linear elastic materials. NOTE 1 Not all ceramic materials are equally and linearly elastic in tension and compression, such as some porous materials and some piezoelectric materials. With the exception of Method C, the test assumes that the test piece has isotropic elastic properties. Method C may be used to determine the degree of anisotropy by testing in different orientations. NOTE 2 An ultrasonic method for dealing with anisotropic materials (ceramic matrix composites) can be found in ENV 14186 (see Bibliography). An alternative to Method D for isotropic materials using disc test pieces is given in Annex A. NOTE 3 At high porosity levels all of the methods except Method C can become inappropriate. The methods are only suitable for a maximum grain size (see EN 623-3), excluding deliberately added whiskers, of less than 10 % of the minimum dimension of the test piece. NOTE 4 The different methods given in this European Standard can produce slightly different results on the same material owing to differences between quasi-isothermal quasi-static an

Skaityti, komentuoti projektą Peržiūrėti metaduomenis

Būtini slapukai

Statistikos slapukai

El. pašto prenumerata

Išplėstinė paieška

Rezultatai

Greitieji filtrai

Organizacija

Technikos komitetas

ICS